Fujitsu FTP-627 Series User manual

1
NOT FOR NEW
DESIGN
FTP-627 Series
■OVERVIEW
The FTP-627 MCL Series consists of 24V drive ultra compact
printers with 2 inch paper widths (58mm), which can print at
high speed. Paper can be easily set by an unique platen
release mechanism.
The FTP-627 MCL series can be used for a variety of
applications, such as portable terminals, POS, ticket issuing
terminals, label printers, and measurement and medical
equipment.
■HIGHLIGHTS
• Ultra compact
Height 15.5 mm, width 69.6 mm, depth 34.3 mm (MCL002)
• High speed printing
It can print at 60 mm/s (480 dotlines/s) maximum by using
Fujitsu's unique head drive control.
• With Auto Cutter
Two types of compact cutters, a full cut and a partial cut, are
in series.
• High resolution printing / Kanji supported
8 dots/mm of resolution printing is possible.
• Easy paper setting
Our unique platen release mechanism allows a
wide paper route even if the printer is ultra-compact, so
paper can be easily inserted. Auto loading is also available
on MCL001, MCL003 and MCL303 models.
• Two types of paper routes
Front and bottom paper feed.
• Easy mounting
Head,motor,sensorandothercomponentwiringareunified
to one flexible cable, and the mechanism can be secured by
one hook and two screws at two locations, making mounting
easy.
24V, 2" HIGH SPEED THERMAL PRINTER

2
FTP-627MCL Series
NOT FOR NEW
DESIGN
■PART NUMBERS
■SPECIFICATIONS
Part number FTP-627MCL001/002/003/004/303#01/303#02
Printing method Thermal-line dot method
Dot structure 384 dots/line
Dot pitch (Horizontal) 0.125 mm (8 dots/mm)—Dot density
Dot pitch (Vertical) 0.125 mm (8 dots/mm)—Line feed pitch
Effective printing area 48 mm
Number of columns ANK 32 columns/line (maximum 12x 24 dot font)
Paper width 58 mm +0
Paper thickness 60 to 80 µm (some paper in this range may not be used because of
paper characteristics)
Printing Speed Maximum 60mm/sec. (480 dot line/sec.)
Alphanumeric, katakana: 159 types
International and special characters: 195 types
JIS Kanji level 1, level 2, non-Kanji
(supported only by FTP-627DSL112, DCL111): about 6800 types
12 ×24 dots, (1.5 ×3.0 mm), 32 columns: alphanumeric, katakana
24 ×24 dots, (3.0 ×3.0 mm), 16 columns: alphanumeric, katakana, Kanji
8 ×16 dots, (1.0 ×2.0 mm), 48 columns: alphanumeric, katakana
16 ×16 dots, (2.0 ×2.0 mm), 24 columns: alphanumeric, katakana, Kanji
SpecificationsItem
Character types
Character, dimensions (H×W), number of
columns
metIrebmuNtraP
msinahcemretnirP
hctiwsnoitcetednepodaehtuohtiwnoitresnirepaptnorf(100LCM726-PTF hctiwsnoitcetednepodaehtuohtiwnoitresnirepapmottob(200LCM726-PTF )bonkdnahctiwsnoitcetednepodaehhtiwnoitresnirepaptnorf(300LCM726-PTF )hctiwsnoitcetednepodaehhtiwnoitresnirepapmottob(400LCM726-PTF
rettuchtiwmsinahceM rettuctucllufhtiw300LCM10#303LCM726-PTF
rettuctuclaitraphtiw300LCM20#303LCM726-PTF
gnivirdrofISL101UC726-PTF
ecafretnI
draoB
ylnoKNA )lairesC232SR(110LSD726-PTF
)scinortneC(110LCD726-PTF
ijnaK
detroppus ,)hsalfhtiwlairesC232SR(211LSD726-PTF )scinortneC(111LCD726-PTF
-1

3
FTP-627MCL Series
NOT FOR NEW
DESIGN
■SPECIFICATIONS
metInoitacificepS
ecafretnI scinortneC/C232SRotsmrofnoC
rewoP
ylppus
daehtnirproF ,C˚52(A1.1.xorppatnerruc,tnerrucegareva%5±CDV42
)stod46,NOylsuoenatlumis,V42)0051=vaR
retnirpforotomroFmumixamA1,%5±CDV42
rettucforotomroFmumixamA1,%5±CDV42
cigolroFmumixamA2.0,%5±CDV5
snoisnemiD
msinahcemretnirP )dedulcxerevel(300LCM,)HxDxW(mm5.51x7.53x5.38
rettuchtiwmsinahceM )dedulcxeeraselbacdnaswercs(,)HxDxW(mm4.62x0.34x5.38
draobecafretnImm42x98x131
thgieW
tuohtiwmsinahcemretnirP
rettuc g55yletamixorppA
htiwmsinahcemretnirP
rettuc g021yletamixorppA
efiL
daeH dradnatsruorednu(tod/seslupnoillim001:ecnatsiseresluP mk05ecnatsidgnilevartrepap:ecnatsisernoisarbA.)snoitidnoc
)sselro%52:oitartnirp(
rettuCmuminim000,003
gnitarepO
tnemnorivne
erutarepmetgnitarepO sinoitarepo,egnarecnarussaytisnedgnitnirp(C˚04+otC˚5+
)C˚04+otC˚0taelbissop
ytidimuhgnitarepO)noitasnednocon(HR%58ot02
erutarepmetegarotS)dedulcnitonrepap(C˚06+otC˚02-
ytidimuhegarotS)noitasnednocon(HR%59-5
noitceteD
noitcnuf
noitcetederutarepmetdaeHrotsimrehtybdetceteD
noitcetedkram/tuorepaPretpurretni-otohpybdetceteD
noitcetedpudaeH )ylno2#303/1#303/400/300(hctiws-edilsybdetceteD
repapevitisneslamrehtdednemmoceR
:repapevitisneshgiH)repaPnoppiN(4E-SK05FT
:repapdradnatS)repaPnoppiN(E-SK06F
)mm85(4010P020-PTF,100UP020-PTF
)repaPijO(R051DP
)mm85(1070P020-PTF
egarotsefilmuideM
:repap )repaPnoppiN(1F-SK06FT )mm85(2010P-PTF
)repaPijO(R071DP
)repaPihsibustiM(1-BBV022P
:repapegarotsefilgnoL
)repaPijO(N-R06DP
)repaPihsibustiM(532-PFA
)repaPnoppiN(R-JK05PT
)repaPihsibustiM(AA022AH

4
FTP-627MCL Series
NOT FOR NEW
DESIGN
■FUNCTION
■DIMENSIONS
1. Printer mechanism
Unit: mm
metImetI
.1noitcnuftnirptseT.8noitcetedytilamronbarettuC
.2noitcetedtuorepaP.9noitcnufgnivasrewoprotoM
.3noitceteddneraenrepaP.01noitcnufnoitcetedkraM
.4noitcetedpudaeH.11noitcetedytilamronbanoitarepoUCM
.5 ytilamronbaerutarepmetdaehlamrehT
noitceted .21noitcetorpecneuqesFFO/NOrewoP
.6noitcetedesuftuo-wolB.31noitcetorptnerruc-revorotoM
.7noitcetedytilamronbaegatlovdaeH.41remiterawdraH

5
FTP-627MCL Series
NOT FOR NEW
DESIGN
2. Interface board
Unit: mm
130.8
83.8
55.9
6.4
5.1
88.9
78.7
39.4
5.1 30.591.4
120.75.1
39.4
4 - ø 3.6±0.1
CN10
CN11*
CN5**CN2
CN8
CN1
Part mounting side
Part solder side
* CN11 used
** CN5 used for paper near end detection

6
FTP-627MCL Series
NOT FOR NEW
DESIGN
■PRINTER CONNECTOR (CN8) (FLEXIBLE PT BOARD) PIN ARRAYS
Control circuit side connector: 52030-3010 Molex or equivalent product
No. Signal I/O Contents No. Signal I/O Contents
1 PHK — Photo interrupter (cathode) 2 VSEN I Power supply for paper sensor
3 PHE O Photo interrupter (emitter) 4VH I Head driving power supply
5VH I Head driving power supply 6 GNC — Ground for head
7 GND — Ground for head 8 DIN I Data input
9 LAT I Data latch 10 CLK I Clock
11 STB6 I Enable 6 12 STB5 I Enable 5
13 STB4 I Enable 4 14 VDD I Logic Power supply
15 STB3 I Enable 3 16 STB 2 I Enable 2
17 STB1 I Enable 1 18 TH O Thermistor
19 TH O Thermistor 20 GND — Ground for head
21 GND — Ground for head 22 VH I Head driving power supply
23 VH I Head driving power supply 24 N.C. — Open terminal
25 SW1 I Head open switch* 26 SW2 O Head open switch*
27 MT/B I Stepping motor coil 28 MT/B I Stepping motor coil
excitation signal B excitation signal B
29 MT/A I Stepping motor coil 30 MT/A I Stepping motor coil
excitation signal A excitation signal A
* on MCL003 / MCL004/ MCL303#01 and MCL303#02 models

7
FTP-627MCL Series
NOT FOR NEW
DESIGN
No. Signal I/O Contents No. Signal I/O Contents
1 PRSTB I Data strobe 2 PRSTB-RET — Connected to logic GND
3 PRDT0 I Data 0 4 PRDT0-RET — Connected to logic GND
5 PRDT1 I Data 1 6 PRDT1-RET — Connected to logic GND
7 PRDT2 I Data 2 8 PRDT2-RET — Connected to logic GND
9 PRDT3 I Data 3 10 PRDT3-RET — Connected to logic GND
11 PRDT4 I Data 4 12 PRDT4-RET — Connected to logic GND
13 PRDT5 I Data 5 14 PRDT5-RET — Connected to logic GND
15 PRDT6 I Data 6 16 PRDT6-RET — Connected to logic GND
17 PRDT7 I Data 7 18 PRDT7-RET — Connected to logic GND
19 ACKNLG O Data input acknowledge 20 ACKNLG-RET — Connected to logic GND
21 BUSY O Busy 22 BUSY-RET — Connected to logic GND
23 RINF2 O Printer status 2 24 INPRM-RET — Connected to logic GND
25 SLCTIN I Printer select 26 INPRM I Reset
27 RINF1 O Printer status 1 28 RINF3 O Printer status 3
29 ATF I Paper feed request 30 GND — Logic GND
Notes:
• Symbol “——” means a negative logic signal.
• “–RET” signal is a return signal of the twisted pair cable.
• “I” or “O” means a signal direction from the interface board side.
(3) Connector pin number (4) Data input signal timing
FCN-605Q030-G/S(Fujitsu Components)
(2) Connector pin assignment
■INTERFACE
1. Centronics interface
(1) Connector (CN1)
Connector part number : FCN-605Q030-G/S (Fujitsu Components) or equivalent
Mating connector part number : FCN-607B030-G/D (Fujitsu Components) or equivalent
PRDT0~7
PRSTB
BUSY
ACKNLG
t1 t3
t2
t4
t5
Data set time
PRSTB pulse width
Data hold time
PRSTB to BUSY= “H”
ACKNLG pulse time
:t1≥0.5 µsec
:t2≥0.5 µsec
:t3≥0.5 µsec
:t4≤0.5 µsec
:t5≈5.0 µsec

8
FTP-627MCL Series
NOT FOR NEW
DESIGN
2. RS-232C
(1) Connector (CN2)
Connector part number : B6B-XH-A (J.S.T.) or equivalent
Mating connector part number : XHP-6 (J.S.T.) or equivalent
(2) Connector pin assignment
Notes:
• Symbol “——” means a negative logic signal.
• “I” or “O” means a signal direction from the interface board side.
(5) Printer status signals
sutatsrorrE1FNIR2FNIR3FNIR
.1tuorepaPwoLhgiHwoL
.2dneraenrepaPhgiHhgiHwoL
.3pudaeHhgiHwoLwoL
.4ytilamronbaerutarepmetdaeHhgiHwoLhgiH
.5ytilamronbaegatlovdaeHwoLhgiHhgiH
.6ytilamronbaerawdraHhgiHhgiHhgiH
.7ytilamronbanoitcetedkraMwoLwoLwoL
.8lamroNwoLwoLhgiH
Cutter (CN11)
.oNlangiSO/I.oNstnetnoC.oNlangiSO/I.oNstnetnoC
1GF- dnuorgemarF2DRI atadevieceR
3DTO atadnoissimsnarT4RTDO ydaerlanimretataD
5DNG- dnuorglangiS6RSDI ydaertesataD
7NITCLSI tcelesretnirP8MRPNIIteseR
9FTAI tseuqerdeefrepaP01DWPI noitallecnacnwodrewoP
langis

9
FTP-627MCL Series
NOT FOR NEW
DESIGN
■CONNECTOR PIN ASSIGNMENT
1. Connector for power supply (CN10)
Part number : B6B-VH White (J.S.T) or equivalent (board side)
Mating connector part number: VHR-6 (J.S.T.) or equivalent
2. Connector for printer mechanism connection (CN8)
Part number : 52030-3010 (made by Molex) or equivalent (board side)
No. Signal I/O Contents No. Signal I/O Contents
1 PHK — Photo interrupter (cathode) 2 VSEN O Power supply for paper senor
3 PHE I Photo interrupter (emitter) 4VH O Head driving power supply
5VH O Head driving power supply 6 GNC — Ground for head
7 GND — Ground for head 8 DIN O Data input
9 LAT O Data latch 10 CLK O Clock
11 STB6 O Enable 6 12 STB5 O Enable 5
13 STB4 O Enable 4 14 VDD O Logic Power supply
15 STB3 O Enable 3 16 STB 2 O Enable 2
17 STB1 O Enable 1 18 TH I Thermistor
19 TH I Thermistor 20 GND — Ground for head
21 GND — Ground for head 22 VH O Head driving power supply
23 VH O Head driving power supply 24 N.C. — Open terminal
25 SW1 O Head open switch* 26 SW2 I Head open switch*
27 MT/B O Stepping motor coil 28 MT/B O Stepping motor coil
excitation signal B excitation signal B
29 MT/A O Stepping motor coil 30 MT/A O Stepping motor coil
excitation signal A excitation signal A
* on MCL003 / MCL004/ MCL303#01 and MCL303#02 models

10
FTP-627MCL Series
NOT FOR NEW
DESIGN
■OPTIONS
emaNrebmuNtraP)mm(htgneL
elbaCecafretnI
dnadraobneewteb(
)tnempiuqe
)1NC(scinortneCroF102Y226-PTF005
)2NC(C232SRroF103Y226-PTF003
)01NC(elbacylppusrewoP104Y226-PTF003
deriuqerfi)5NC(rosnesrepapdneraeN-PTF