Fujitsu FI-4010CU Manual

fi-4010CU Image Scanner
Operator’s Guide
P3PC-E702-03EN

i
Disclaimers

FCC declaration
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC warning
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE
• The use of a non-shielded interface cable with the referenced device is
prohibited. The length of the parallel interface cable must be 15 meters (50
feet) or less.
• The length of the power cord must be 3 meters (10 feet) or less.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conformme à la norme NMB-003 du
Canada.

ii

Bescheimigung des Herstellers / Importeurs
Hiermit wird bescheinigt, daß der/dieldas
•fi-4010CU in Übereinsstimmung mit den Bestimmungen der
•AmtsblVfg 243/1991 funkentstört ist. Der Deutschen Bundespost wurde das
Inverkehrbringen dieses Gerätes angezeigt und die Berechtigung zur Überprüfung
der Serie auf Einhaltung der Bestimmungen eingeräumt.
•Maschinenlärminformationsverordnung 3. GS GV, 18.01.1991:
Der höchste Schalldruckpegel beträgt 70 dB (A) order weniger gemäß ISO/7779.

Use in Enhanced Safety Applications
This Product is designed, developed and manufactured as contemplated for
general use, including without limitation, general office use, personal use,
household use, and ordinary industrial use, but is not designed, developed and
manufactured as contemplated for use accompanying fatal risks or dangers that,
unless extremely high safety is secured, could lead directly to death, personal
injury, severe physical damage or other loss (hereinafter “High Safety Required
Use), including without limitation, nuclear reaction control in nuclear facility,
aircraft flight control, air traffic control, mass transport control, medical life
support system, missile launch control in weapon system. You shall not use this
Product without securing the sufficient safety required for the High Safety
Required Use. If you wish to use this Product for High Safety Required Use,
please consult with our sales representatives in charge before such use.
The manufacturers accept no claims from customers or third parties in relation to,
and accepts no responsibility for losses incurred as a result of, the use of this
product in enhanced safety applications.

About the use of mercury
Scanner lamp includes mercury.
To avoid unexpected injury, read the followings carefully.
Doing following actions may result in serious personal injuries:
As an ENERGYSTAR ®Partner, Fujitsu Limited has determined that
this scanner meets ENERGYSTAR ®guidelines for energy efficiency.
ENERGYSTAR ®is a U. S. registered mark.

iii
 Put the substance in the lamp into mouth as it contains mercury.
 Vaporize, crumb, condense the scanner.
 Aspirate the chemical liquid contained in scanner parts.
Dispose of the scanner should be conducted as required by local ordinances or
regulations.

Copying
Copying of paper money, coins, securities and passports issued by government
authorities, licenses and permits issued by public authorities and private
organizations, official documents, and private documents etc. is illegal and is
subject to punishment.

Copyright
Copyright had items such as books, paintings, prints, maps, drawings, and
photographs may be copied only for private or home use, or for similar
applications.
Copying for other applications without the consent of the holder of the copyright
is illegal.

Trademarks and Registered Trademarks
Microsoft®, Windows® and Windows® NT are registered trademarks of the
Microsoft Corporation in the United States of America and in other countries.
ISIS® is the registered trademark of Pixel Translations, a division of Actionpoint
Inc.
Adobe and the Adobe logo as well as Acrobat and the Acrobat Logo are
trademarks of Adobe Systems Incorporated.
Names of other goods and products occurring in this manual are the registered
trademarks or trademarks of the relevant companies.
The contents of this manual may be revised without prior notice.
All Rights Reserved, Copyright © 2001-2002 PFU LIMITED.
No part of this manual may be reproduced in any form without permission.

iv
Fujitsu Group Offices
Please send your comments on this manual or on Fujitsu products to the
following addresses:
FUJITSU COMPUTER PRODUCTS
OF AMERICA, INC.
2904 Orchard Parkway, San Jose,
CA 95134-2009, U.S.A.
Phone: [phone];
(1-408)432-6333
Technical Assistance Center:
(1-800)626-4686
Fax: [phone]
Website: http://www.fcpa.com/
E-mail: [email protected]
FUJITSU EUROPE LTD.
Hayes Park Central, Hayes End
Road, Hayes Middlesex UB4 8FE,
UK
Phone: [phone]
Fax: [phone]
Website:
http://www.fujitsu-europe.com/
E-mail:
[email protected]
FUJITSU ITALIA S.p.A.
Via Nazario Sauro, 38
20099 Sesto San Giovanni (Milan),
Italy
Phone: [phone]
Fax: [phone]
Website:
http://www.fujitsu-europe.com/
FUJITSU AUSTRALIA LTD
Fujitsu House 2 Julius Avenue
North Ryde, N.S.W 2113 Australia
Phone: [phone]
Fax: [phone]
Website: http://au.fujitsu.com/
FUJITSU CANADA, INC.
2800 Matheson Boulevard East,
Mississauga, Ontario L4W
4X5, Canada
Phone: [phone]
Fax: [phone]
Website: http://www.fujitsu.ca/
E-mail: [email protected]
(For Sales Questions)
[email protected]
(For technical questions)
FUJITSU DEUTSCHLAND GMBH.
Frankfurter Ring 211,
80807 München 40, Germany
Phone: [phone]
Fax: [phone]
Website: http:// de.fujitsu.com/
E-mail: [email protected]
FUJITSU ICL ESPANA, S.A.
Camino Cerro de los Gamos,
1 28224,Pozuelo de Alarcon, Madrid,
Spain
Phone: [phone]
Fax: [phone]
Website:
http://www.fujitsu-europe.com/
E-mail: [email protected]
FUJITSU TAIWAN LTD.
19th Fl., No39, Sec.1 Chung-Hwa
Rd.,Taipei, Taiwan R.O.C.
Phone: [phone]
Fax: [phone]
Website: http://fw.fujitsu.com/

v
FUJITSU SYSTEMS BUSINESS
(THAILAND) LTD.
12th Fl., Olympia Thai Tower, 444
Rachadapisek Road, Samsennok,
Huay kwang, Bangkok 10320,
Thailand
Phone: [phone]
Fax: [phone]
Website: http://th.fujitsu.com/
FUJITSU MALAYSIA SDN, BHD.
7th Fl., Wisma Damansara,
Jalan Semantan 50490 Kuala
Lumpur, MALAYSIA
Phone: [phone]
Fax: [phone]
Website: http://my.fujitsu.com/
FUJITSU PHILIPPINES, INC
2nd Fl., United Life Building, Pasay
Road, Legaspi Village Makati,
Metro Manila, Philippines
Phone: [phone]
Fax: [phone]
Imaging Products Division,
PFU LIMITED
Solid Square East Tower,
580 Horikawa-cho, Saiwai-ku,
Kawasaki-shi, Kanagawa
212-8563, Japan
Phone: [phone]
Fax: [phone]
Website:
http://imagescanner.fujitsu.com/
E-mail: [email protected]
FUJITSU ASIA PTE.LTD.
20 Science Park Road, #03-01,
Tele Teck Park Singapore Science
Park II,
Singapore 117674
Phone: [phone]
Fax: [phone]
Website: http://sg.fujitsu.com/
E-mail: [email protected]
FUJITSU HONG KONG LTD.
10/F., Lincoln House, 979 King's
Road, Taikoo Place, Island East,
Hong Kong
Phone: [phone]
Fax: [phone]
Website: http://hk.fujitsu.com/
E-mail: [email protected]
FUJITSU KOREA LTD.
5-11 Fl., Coryo Finance Center
Building,
Youido-Dong 23-6, Young
DungPo-gu,
Seoul, Korea, 150-010
Phone: [phone]
Fax: [phone]
Website: http://kr.fujitsu.com/
E-mail: [email protected]
PFU LIMITED
(Corporate headquarters)
Nu 98-2 Unoke, Unoke-machi,
kahoku-gun, Ishikawa 929-1192,
Japan
Phone: [phone]
Fax: [phone]

vi
Note, Liability
READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
IF NOT USED CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO
USERS OR BYSTANDERS.
While all efforts have been made to ensure the accuracy of all information in this
manual, PFU assumes no liability to any party for any damage caused by errors
or omissions or by statements of any kind in this manual, its updates or
supplements, whether such errors are omissions or statements resulting from
negligence, accidents, or any other cause.
PFU further assumes no liability arising from the application or use of any
product or system described herein; nor any liability for incidental or
consequential damages arising from the use of this manual.
PFU disclaims all warranties regarding the information contained herein, whether
expressed, implied, or statutory.
PFU reserves the right to make changes to any products herein, to improve
reliability, function, or design, without further notice and without obligation.

vii
Preface
This manual explains how to use the fi-4010CU image scanner.
This manual contains chapters on the following topics:
COMPONENTS
INSTALLATION AND CONNECTIONS
OPERATING INSTRUCTIONS
MAINTENANCE
TROUBLESHOOTING
INSTALLATION SPECIFICATIONS
It also contains a Glossary of Terms and an Index.

viii
Conventions
Important information that requires special attention is indicated as follows:
WARNING
WARNING indicates that serious personal injury may result if you do not follow a
procedure correctly.
CAUTION
CAUTION indicates that minor personal injury, loss of data, or damage to the
scanner may result if you do not follow a procedure correctly.
NOTE
A NOTICE provides “how to” tips or suggestions to help you perform a
procedure correctly.
A TRIANGLE symbol indicates that special care and attention is required.
The drawing inside the triangle shows the specific caution.
A CIRCLE with a diagonal line inside shows action that users are not
allowed to do.The drawing inside or under the circle shows the specific
action that is not allowed.
Outline characters on a colored background show instructions users
should follow. It may include the drawing that shows the specific
instruction.
R

ix
Screen Examples In This Manual
The screen examples in this manual are subject to change without notice in the
interest of product improvement.
If the actual displayed screen differs from the screen examples in this manual,
operate by following the actual displayed screen referring to the User's Manual
of the scanner application you are using.
Furthermore, the screenshots in this manual are for the FUJITSU TWAIN32
scanner driver and the Image Capturing Software Utilities "ScandAll 21" for
Microsoft® Windows®.

x
Precautions
This section describes precautions to follow when installing the scanner.
To ensure the longevity and proper functioning of your scanner, do not install the
scanner in the places and environments described below.

Warning
Important warnings employed in this manual are as follows.
Do not damage the power cable.
Damage to the power cable may result in fire or electric shock.
Do not place heavy objects on, pull, tightly bend, twist, heat, or
modify the power cable.
Do not use the power cable or socket if it is damaged, or if the plug
is loose in the socket.
Use only the specified power cable or extension cable.
Use only the specified power cable or extension cable. Use of other
cables may result in electric shock or malfunction.
Use only at the specified voltage. Ensure that too many cables are not
connected to the same socket.
Use at other than the specified voltage may result in fire or electric
shock.
Ensure that too many cables are not connected to the same socket.
Wipe all dust from plug on the power supply cable.
Using a dry cloth, remove all dust on the metal components of the
plug, and on all surfaces to which the metal components are
attached.
Presence of dust may result in fire or electric shock.

xi
Do not use the equipment in areas with high levels of oil smoke, steam,
humidity, or dust.
Installation in areas with high levels of oil smoke, steam, humidity, or
dust may result in fire or electric shock.
Do not use the equipment if an abnormal smell or noise is apparent.
If the equipment overheats, emits smoke or abnormal smells, or
makes abnormal noises, switch power OFF immediately and
remove the power plug from the socket.
Check that smoke is no longer emitted, and calls your dealer or
maintenance service center. Do not attempt to repair the equipment
yourself under any circumstances.
Ensure that water or foreign matter does not enter the equipment.
Do not insert or drop metal objects or combustible objects into
openings (e.g. ventilation openings).
Ensure that liquids (e.g. coffee) and metal objects (e.g. paper clips)
do not enter the equipment.
Do not spill or leak water onto the equipment.
If foreign matter (e.g. water, other liquids, metal objects) enters the
equipment, switch power OFF immediately and remove the power
plug from the socket, and call your dealer or maintenance service
center. Particular care is required if children are in the vicinity.
Do not open the equipment without good reason.
The equipment contains high-voltage components, and should not
be dismantled or modified.

xii
Always remove the plug from the socket before fitting or removing optional
equipment.
Switch the equipment power supply OFF, and remove the plug from
the socket, before fitting or removing optional equipment in
accordance with the specified procedure.
Grip the plug to remove the power cable from the socket.
Switch power OFF if the equipment is damaged.
If the equipment is dropped, or covers etc. have been damaged,
switch power supply OFF, remove the plug from the socket, and call
your dealer or maintenance service center.
Do not place in wet areas.
Do not place the scanner where liquid spills may occur.

Caution
Important cautions employed in this manual are as follows.
Do not touch the power cable with wet hands.
Do not remove or insert the plug with wet hands. Wet hands may
result in electric shock.
Do not look at the light source directly.
Do not look at the light source of the equipment directly as this May
result in injury.

xiii
Always ensure that the equipment is installed in a stable location.
Ensure that no part of the scanner is liable to fall from the desk, and
that the base of the equipment is level.
Ensure that the equipment is installed in a stable location. The
equipment should be installed in a location that is level and subject
to minimal vibration.
Insert the power plug fully into the socket.
Ensure that the power plug is inserted as far as possible into the
socket.
Do not block the ventilation openings.
If the ventilation openings are blocked the interior of the equipment
will overheat, and may result in fire or malfunction.
Do not place heavy objects on, and do not stand on, the equipment.
Placing heavy objects on the equipment, or standing on the
equipment while working, may result in injury.
Remove the power plug from the socket before moving the equipment.
Moving the equipment with the cable connected may result in
damage to the cable, fire or electric shock, or injury. Always remove
the power plug from the socket, and disconnect extension cables,
before moving the equipment.
Always clear the floor before beginning work.
Avoid static electricity.
Ensure that the equipment is installed away from strong magnetic
fields, sources of electrical noise and airflow.
If the scanner is used near an air conditioner, copying machine, or
TV set, the scanner may operate incorrectly.
Avoid static electricity. Static electricity may be a cause of
mis-operation of the equipment. Ensure that the floor and desk on
which the equipment is installed is of a material that does not
generate static electricity.

xiv
Ensure that clothing, ties, and hair do not become caught in gears and
rollers.
Clothing, ties, and hair becoming caught in moving components
such as gears and rollers may result in injury.
Remove the power plug from the socket if the equipment is to be out of use
for a considerable length of time.
For safety reasons, the power plug should be removed from the
socket if the equipment is to be out of use for a significant time.
Remove the power cable from the socket immediately thunder is heard.
Remove the power cable from the socket if thunder is heard nearby.
The equipment may be damaged if it remains connected during an
electrical storm.
Do not leave the equipment in direct sunlight.
Leaving the equipment in direct sunlight or in the vicinity of air
conditioning equipment will result in the internal temperature of the
equipment increasing, and may result in fire or malfunction.
Ensure that the equipment is installed in a well ventilated area.
Do not use aerosol spray near the scanner.
Do not use aerosol sprays, for example, to clean the scanner.
Air sprayed from aerosol sprays cause dirt and dust to enter the
scanner, resulting scanner failure and malfunction.
April, 2002 Rev.03

xv
CONTENTS
Chapter 1. COMPONENTS ___________________________________ 1
1.1 Overview ___________________________________________________________ 1
1.1.1 Features of fi-4010CU image scanner_________________________________ 1
1.2 Checking the Components _____________________________________________ 2
Chapter 2. INSTALLATION AND CONNECTIONS ____ 5
2.1 Unlock the Shipping lock ______________________________________________ 5
2.2 Installation of the ADF paper chute A, ADF paper chute B and Document stopper
_______________________________________________________________________ 6
2.3 Connecting the interface cables _________________________________________ 7
2.3.1 Connecting USB cable _____________________________________________ 7
2.3.2 Connecting ADF cable_____________________________________________ 7
2.3.3 Connecting Power cable____________________________________________ 7
2.3.4 Installation of scanner driver and software_____________________________ 8
Chapter 3. OPERATING INSTRUCTIONS _______________ 9
3.1 Loading Documents on the Flatbed ______________________________________ 9
3.1.1 Check the document condition ______________________________________ 9
3.1.2 Reading a Page from a Thick Book__________________________________ 10
3.2 Scanning document with ADF _________________________________________ 11
3.2.1 Confirming document condition ____________________________________ 11
3.2.2 Setting documents _______________________________________________ 13
3.3 Scanning documents _________________________________________________ 15
Chapter 4. MAINTENANCE__________________________________ 16
4.1 How to solve paper jams______________________________________________ 16
4.2 Daily maintenance ___________________________________________________ 17
4.3 Cleaning ___________________________________________________________ 17

xvi
4.3.1 Cleaning materials _______________________________________________ 17
4.3.2 Cleaning the Flatbed unit ___________________________________________ 18
4.3.3 Cleaning the ADF unit ____________________________________________ 19
4.4 Consumables _______________________________________________________ 22
4.4.1 Part number and Replacement cycle _________________________________ 22
4.4.2 Replacing Pad ASY ______________________________________________ 23
Chapter 5. TROBLESHOOTING ___________________________ 26
A. Installation Specifications ______________________________ 28
Dimensions __________________________________________________________ 28
GLOSSARY OF TERMS ______________________________________ 29
INDEX ______________________________________________________________ 32
Declaration of Conformity __________________________________ 34

1
Chapter 1. COMPONENTS
This section describes checking the components, Units, and Assemblies of the scanner,
and operator panel arrangement, and the function of parts.
1.1 Overview
This section describes overview and features of fi-4010CU.
1.1.1 Features of fi-4010CU image scanner
fi-4010CU image scanner (this equipment) can scan high-quality image.
The scanner can perform the following functions when used in conjunction with
software applications.
- Save images in several formats such as TIFF and Bitmap
- Output data to a printer when connected to a personal computer.
Features
- High quality ADF (Automatic document feeder)
It meets business purpose
- Compact and lightweight
Easytoinstall
- Color scanning at 600x600dpi

2
1.2 Checking the Components
These high precision components must be handled carefully.
Confirm that all the components shown in the following figure have been received.
If any component is missing, please contact your sales agent.
Quick Installation Guide
Scanne
r
driver
(
CD-ROM
)
Document
sto
pp
e
r
USB cable
A
C ada
p
to
r
A
DF paper chute A
Power cable
PAD AS
Y
Operator’s Guide
(this book) User Manual
(
CD-ROM
)
A
dobeAcrobat5.0
(CD-ROM)
A
DF paper chute B

3
1.3 Units and Assemblies
This section shows the exterior view and assemblies of the scanner.
This section also provides the name of each part and describes its functions.
 Units
Front side
Part Function
ADF paper chute A and
ADF paper chute B
Holds the documents to be fed by the automatic
document feeder (ADF).
Side guide Holds the documents straight.
Document stopper Needs to be adjusted dependent upon paper size
being fed into the ADF.
Document cover ADF: Stacks the read documents.
Flatbed: Closes over and keeps in place the document
toberead.
Automatic document feeder
(ADF)
Automatically feeds documents to the reading
position.
Automatic document
feeder (ADF)
ADF cover
Side guide
ADF paper chute B
Ready lamp
Power lamp
Check lamp
Document cover
Document
sto
pp
e
r
ADF paper chute A
Flatbed