Fujitsu fi 5750C - Document Scanner User manual

for Fujitsu Scanners
Cleaning and Consumable Replacement Instructions
IManualnstruction
Versitec is a division of Cranel, Inc.
fi-5750C/fi-5650C

1
INSTRUCTION MANUAL FOR
FUJITSU
-5750 C/-5650C SCANNER

27
Cleaning the ADF Components ........................................... 3
Cleaning the Flatbed .......................................................... 5
Cleaning the ADF Components ........................................... 5
Replacing the Brake Rollers ................................................. 6
Replacing the Pick Rollers .................................................... 7
FI -5750CS CANNER
TABLE OF CONTENTS
Install the new brake roller set into the door with the shiny black roller on
the left.
Close the brake roller compartment door. If you encounter any resistance
dellatsnisitesrellorekarbehttahterusekam,roodehtgnisolcni
.ylreporp
Close the ADF and resume scanner operation
To reset the Brake Roller Counter see your scanner manual or consult with
your computer software support department.
Press the two blue buttons to open the ADF
Replacing the Pick Rollers

63
Repeat this until the sheet is noticeably dirty.
Discard the cleaning sheet
REPLACING THE CONSUMABLES
Replacing the Brake Rollers
Press the two blue buttons to open the ADF
Open the brake roller compartment door
Lift the brake roller set from the door. Note the orientation of the shiny
black roller on the left side of the compartment door.
CLEANING AND REPLACING CONSUMABLES
Cleaning the Automatic Document Feeder (ADF) Components
CAUTION
Disconnect the scanner from power outlet
CAUTION
Allow the glass in the ADF to cool for at least three
minutes before cleaning it
Press the two blue buttons to open up the ADF compartment
Use a clean cloth moistened with V1 cleaner to wipe the entire
surface of these components:
a. brake rollers - you may want to open the brake roller
compartment to clean these rollers as they are dicult
to turn
b. pick rollers - turn one roller while wiping the surface of
the other roller down.

45
Clean these components with the cloth moistened with V1 cleaner as well:
a. chute roller
b. pick arm
c. feed rollers
d. sheet guide
e. glass ats
Clean the plastic rollers with F2 cleaner
Gently close the ADF after allowing the ADF components to dry for a few
.setunim
Cleaning the Flatbed
Press on the atbed cover handle and carefully lift up until the
cover stays open so that you can access the glass surface.
Wipe the glass surface with a clean cloth moistened with V1 cleaner
Allow the glass surface to dry for a few minutes
Gently close the atbed cover and resume scanner operation
Using a Cleaning Sheet to Clean the ADF Components
Leave the scanner connected to the power outlet.
Let the glass surface cool a few minutes if the scanner has been in
operation recently
Moisten a cleaning sheet with V1 cleaner and feed it through the scanner .

45
Clean these components with the cloth moistened with V1 cleaner as well:
a. chute roller
b. pick arm
c. feed rollers
d. sheet guide
e. glass ats
Clean the plastic rollers with F2 cleaner
Gently close the ADF after allowing the ADF components to dry for a few
.setunim
Cleaning the Flatbed
Press on the atbed cover handle and carefully lift up until the
cover stays open so that you can access the glass surface.
Wipe the glass surface with a clean cloth moistened with V1 cleaner
Allow the glass surface to dry for a few minutes
Gently close the atbed cover and resume scanner operation
Using a Cleaning Sheet to Clean the ADF Components
Leave the scanner connected to the power outlet.
Let the glass surface cool a few minutes if the scanner has been in
operation recently
Moisten a cleaning sheet with V1 cleaner and feed it through the scanner .

63
Repeat this until the sheet is noticeably dirty.
Discard the cleaning sheet
REPLACING THE CONSUMABLES
Replacing the Brake Rollers
Press the two blue buttons to open the ADF
Open the brake roller compartment door
Lift the brake roller set from the door. Note the orientation of the shiny
black roller on the left side of the compartment door.
CLEANING AND REPLACING CONSUMABLES
Cleaning the Automatic Document Feeder (ADF) Components
CAUTION
Disconnect the scanner from power outlet
CAUTION
Allow the glass in the ADF to cool for at least three
minutes before cleaning it
Press the two blue buttons to open up the ADF compartment
Use a clean cloth moistened with V1 cleaner to wipe the entire
surface of these components:
a. brake rollers - you may want to open the brake roller
compartment to clean these rollers as they are dicult
to turn
b. pick rollers - turn one roller while wiping the surface of
the other roller down.

27
Cleaning the ADF Components ........................................... 3
Cleaning the Flatbed .......................................................... 5
Cleaning the ADF Components ........................................... 5
Replacing the Brake Rollers ................................................. 6
Replacing the Pick Rollers .................................................... 7
FI -5750CS CANNER
TABLE OF CONTENTS
Install the new brake roller set into the door with the shiny black roller on
the left.
Close the brake roller compartment door. If you encounter any resistance
dellatsnisitesrellorekarbehttahterusekam,roodehtgnisolcni
.ylreporp
Close the ADF and resume scanner operation
To reset the Brake Roller Counter see your scanner manual or consult with
your computer software support department.
Press the two blue buttons to open the ADF
Replacing the Pick Rollers

81
Open the Pick Roller compartment door using your thumb
Slide one pair of pick rollers to the right to remove it from the shaft and
replace it with the matching set from your kit. The smoother, smaller, set
of rollers are the rst in the paper path, followed by the larger, treaded
rollers.
Make sure that the notch on the roller set lines up with the screw on the
.ylreporpnrutsrellorehttahtserussasihT.tesrellorhcaefotfahs
Close the Pick Roller compartment door. If the door doesn’t completely
close and lie at, check that the two sets of rollers are installed properly.
Close the ADF and resume scanner operation.
To reset the Pick Roller Counter see your scanner manual or consult with
your computer software support department.
INSTRUCTION MANUAL FOR
FUJITSU
FI-5750CSCANNER