Fujitsu fi-4110CU Series Configuration guide

1
fi-4110CU/M3091/M3092SERIES CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
fi-4110CU/M3091/M3092 SERIES CONSUMABLE REPLACEMENT
AND CLEANING INSTRUCTIONS
CG00002-003401Revision A

fi-4110CU/M3091/M3092SERIES CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
2
KIT CONTENTS
Cotton
Swabs
Qty 1 100/pack
F1 Cleaner
Isopropyl Alcohol
Qty1
Cleaning Paper
Qty 1 10/pack
Lint Free
Cleaning Cloths
Qty 2 20/pack
PadAssembly
Qty 3
GuideAssembly
Qty 1

3
fi-4110CU/M3091/M3092SERIES CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
CONSUMABLES LIST
Description Qty Life Fujitsu P/N
GuideAssembly 1 50,000 PA03209-F014
Pad Assembly 1 12,000 PA03209-F010
Note:
Replacement Cycles are estimated guidelines established by testing
with A4/Letter sized woodfree and wood based 17 lb paper. NCR or
Carbonless paper has chemical composition which damages the
Pad, and the Pick Roller. Cleaning of the consumables will be
required more frequently to avoid feed problems. Consumable life
will be reduced if NCR or Carbonless paper is scanned.
PadAssemblyGuideAssy
CONSUMABLES PAGE COUNT
Goto the Control Panel and Select“Scanners and Cameras Properties”.
Select the device driver and and click the Properties button.

fi-4110CU/M3091/M3092SERIES CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
4
CONSUMABLES PAGE COUNT (CONTINUED)
• Yourcomputer willdisplay the Properties for thescanner you have.
This will show the Pad and Pick Roller page counts on the Device Set
tab.
• TheTargetValue toChange Supplies is a roughestimate of when
suppliesshould be changed with new ones. This amount can vary
dependingonpaper type, frequency of use, print onpages,cleaning
andotherfactors.
• To order new consumables contact the Fujistsu Dealer in your area or
call our TechnicalAssistance Center at the number in your
documentation.
• Clicking the Reset will set the count for each consumable to 0. This
shouldbedone when ever you changeto a new consumable inthe
scanner.

5
fi-4110CU/M3091/M3092SERIES CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
REPLACING THE PAD ASSEMBLY
Adefective or improperly installed PadAssembly can cause misspicks,
skew, or double fed documents. To replace the Pad Assembly perform
the following steps.
• Removealldocuments
fromtheADFPaper
Chute. Open theADF
by pulling theADF
buttonup.
• Removethe Pad
Assembly by pressing
Down on the pick arm
then pull out the pad
assembly to remove it.
• Attach the new Pad
Assembly while
pressingdownonthe
pick arm so it is out of
the way. Be sure to
seat the pad
completelytoavoid
jammingofpaper
beingfed.
Note:
After replacement of any consumable reset the counter for that
consumablebyfollowingthe “Consumables Page Count” Section at
the front of these instructions to reset paper counts.
OpenADF
to Front
ADF button
PadAssy.
PadAssy.
Push down on
pick arm to
remove pad.

fi-4110CU/M3091/M3092SERIES CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
6
REPLACING THE GUIDE ASSEMBLY
• Removealldocuments from
theADFPaper Chute and
removetheADFpaperchute
fromthescanner.Open the
ADFtowards the front of the
scannerwhileholdingupthe
coveropenlever.
• Push the Claw on the Guide
Assemblyinwardswhile lifting
onthehandletoremovethe
GuideAssembly from the
scanner’s feedpath.
Remove Pick
Roller Guide Handle
Claw
Note:
If the GuideAssembly is not fully seated paper jams and miss-feeds
are likely to occur. Don’t forget to reset the counter for the Pick Roller
by right-clicking on the ScanSnap Monitor in the TaskTray.
ADF Paper Chute
ADF
Cover Open
Lever

7
fi-4110CU/M3091/M3092SERIES CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
• Attach theADF paper chute.
Push in the center of theADF
to close, press until you hear
a click which indicates the
ADF is fully closed. The
scannershouldnowbeready
tofeeddocuments.
• SeetheConsumablesPage
CountSectionof these
instructions to reset paper
counts. This should be done
wheneverthe consumables
arechangedoutwithnew
consumables.
REPLACING THE GUIDE ASSEMBLY (CONT.)
Push in Center to
close ADF
ADF Paper
Chute

fi-4110CU/M3091/M3092SERIES CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
8
CLEANING LOCATIONS AND FREQUENCIES
Note:
The scanner will need to be cleaned every day (or possibly more than
once a day) if the following paper is scanned.
• Paper with special coating such as carbonless paper.
• Paper with large amount of printing. (Heavy toner or ink)
• Documents with toner that is not fused properly.
CLEANING MATERIALS
Location Tools Frequency
Cleaning Sheets Every 1,000 Sheets
Cloth & Isopropyl Alcohol Every 5,000 Sheets
Plastic Feed Rollers Cloth & Isopropyl Alcohol Every 5,000 Sheets
Sheet Guides Cloth & Isopropyl Alcohol Every 5,000 Sheets
Eject Rollers Cloth & Isopropyl Alcohol Every 5,000 Sheets
Feed Rollers Cloth & Isopropyl Alcohol Every 5,000 Sheets
Glass Surfaces Cloth & Isopropyl Alcohol Every 5,000 Sheets
Pick Roller and Pad
Cotton
Swabs
F1 Cleaner
Isopropyl Alcohol
Cleaning Paper
Lint Free
Cleaning Cloths

9
fi-4110CU/M3091/M3092SERIES CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
CLEANING THE ROLLERS WITH THE CLEANING PAPER
• Set the Hopper Guides to
the widest width possible.
Thecleaningpapersare designed to remove only loose paper dustandink
from the rollers. Use the cleaning paper approximatelyevery 1,000 sheets
scanned. They are to be used in between the thorough cleanings of the
scanner. Using the cleaning paper does not take the place of the
more complete cleanings described later in this section
• Spray the Cleaning Paper lightlywithF1 Cleaner and place the Cleaning
paperagainst the right edgeof the Hopper Guide.Press the SCAN button
on the front of the scanner to scan the cleaning paper. Do Not Save
These Images. This operation is used only to pass the cleaning paper
through the paper feed path. Check the path to see if it needs further
cleaning, if you find debris in the paper path perform this cleaning or the
(CLEANING THE ADF WITH LINT-FREE CLOTHS) inthefollowingsteps.
• PlacetheCleaningPaperagainstthe Left Hopper Guide and perform the
previousstep.
Hopper Guides
Open
LintFree
Cloth
F1Cleaneror
neutraldetergent
NoPaint Thinner

fi-4110CU/M3091/M3092SERIES CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
10
• Turn Scanner power off.
• OpentheADFcover by
pressing the ADF button.
Disconnect the AC power
plug. Let the scanner cool
for at least 15 minutes after
operation. This is to prevent
burns to your skin as the
lamps will heat the surface
of the glass in the feed path.
• Use F1 Cleaner (90% or
higher Isopropyl Alcohol) on
a lint free cloth and clean the
areas shown in the drawing
to the right. (See following
steps to clean properly)
• Clean the Pad Assembly
usingadownward stroke in
the direction shown to the
right with the lint free cloth
moistened lightly with F1
Cleaner(90% or higher
IsopropylAlcohol).
CLEANING THE ADF WITH LINT-FREE CLOTHS
Note:
Theglasssurfaceinsidethefi-4110EOX2ADFbecomes hot during
scanneroperation. Beforeperformingthiscleaningturn off the scanner
and disconnect theAC adapter from the power outlet, wait at least 15
minutes for the scanner to cool.
CLEANING THE PAD ASSEMBLY.
ADF
button
Front of
Scanner
ADF
SheetGuide(white
partalso on ADF
side).
Pad
Assy
Plastic
Rollers (4)
Feed Rollers (2) PickRoller
EjectRollers
(2)
ADFGlass
PickArm
Pick
spring
Clean the Rubber Portion
in Direction of Arrows
Pick
Arm
Pick
Spring
Pad
Assy.