Fujitsu M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf Manual

M4097D Image Scanner
Operator’s Guide
C150-E146-03EN

M4097D
Image Scanner
Operator's Guide

i
Revisions, Disclaimers
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential instal-
lation. This equipment generates, uses, and can radiate radio frequency energy
and,ifnotinstalledandusedinaccordancewiththeinstructionmanual,maycause
harmfulinterferencetoradiocommunications.However,thereisnoguaranteethat
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equip-
ment.
NOTICE
• The use of a non-shielded interface cable with the referenced device is
prohibited. The length of the parallel interface cable must be 3 meters (10 feet)
orless.Thelengthoftheserialinterfacecablemustbe15meters(50feet)orless.
• The length of the power cord must be 3 meters (10 feet) or less.
noitidE dehsilbupetaD stnetnocdesiveR
100002,yraurbeFnoitidetsriF
200002,yraurbeFnoitidednoceS
300002,yaMnoitidedrihT
NE30-641E-051C.oNnoitacificepS

ii
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conformme àla norme NMB-003 du
Canada.
As an ENERGYSTAR ®Partner, Fujitsu Limited has determined that this scanner
meets ENERGYSTAR ®guidelines for energy efficiency. ENERGYSTAR ®is a
U. S. registered mark.
The contents of this manual may be revised without prior notice.
All Rights Reserved, Copyright © 2000 FUJITSU LIMITED.
Printed in Japan.
No part of this manual may be reproduced in any form without permission.

iii
Fujitsu Offices
PleasesendyourcommentsonthismanualoronFujitsuproductstothefollowing
addresses:
FUJITSU COMPUTER PRODUCTS OF
AMERICA,INC.
2904 Orchard Parkway,San Jose.
California 95134-2022,U.S.A.
TEL:[phone]
FAX:[phone]
http://www.fcpa.com/
FUJITSU AUSTRALIA LIMITED
Fujitsu Hause 2 Julius Avenue North Ryde
N.S.W 2113 AUSTRALIA
TEL:[phone]
FAX:[phone]
http://www.fujitsu.com.au/
FUJITSU CANADA,INC.
2800 Matheson Blvd.East,Mississauga.
Ontario L4W 4X5,CANADA
TEL:[phone]
FAX:[phone]
http://www.fujitsu.ca/
FUJITSU DEUTSCHLAND GmbH.
Frankfurter Ring 211,
8000 München 40,F.R,GERMANY
TEL:[phone]
FAX:[phone]
http://www.fujitsu.de/
FUJITSU ESPAÑA,S.A
Edificio torre Europa 5a
Paseo de la Castellana 95
Madrid 28046,SPAIN
TEL:[phone]
FAX:[phone]
http://www.fujitsu-europe.com/home/
FUJITSU EUROPE LTD.
2,Longwalk Road,Stockey Park,Uxbridge
Middlesex,UB11 1AB,U.K
TEL:[phone]
FAX:[phone]
http://www.fujitsu-europe.com/home
FUJITSU FRANCE S.A.
I, Place des Etats-Unis, SILIC 310,
94588 Rungis cedex, FRANCE
TEL:[phone]
FAX:[phone]
http://www.fujitsu-europe.com/home/
FUJITSU COMPUTERS (SINGAPORE) PTE, LTD.
20 Science Park Road #03-01, Tele Teck Park
Singapore Science Park II, Singapore 117674
Republic of Singapore
TEL:[phone]
FAX:[phone]
http://www.fujitsu-computers.com.sg/
FUJITSU HONG KONG Limited
10/F, Lincoln House, Taikoo Place,
979 King’s Road, Island East, Hong Kong
TEL:[phone]
FAX:[phone]
TLX:62667
http://www.fujitsu.com.hk/
FUJITSU ITALIA S.p.A.
Via Nazario Sauro, 38
20099 Sestos, Giovanni (MI), ITALY
TEL:[phone]
FAX:[phone]
http://www.fujitsu-europe.com/home
FUJITSU NORDIC AB
Kung Hans väg,S-192 68 Sollentuna, SWEDEN
TEL:[phone]
FAX:[phone]
http://www.fujitsu-europe.com/home
FUJITSU LIMITED
International Operations
Marunouchi 1-6-1, Chiyoda-ku,
Tokyo 100 JAPAN
TEL:[phone]
FAX:[phone]
TLX:J2283
Cable:”FUJITSU LIMITED TOKYO”
http://www.fujitsu.co.jp/

iv
Note, Liability
READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
IF NOT USED CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO
USERS OR BYSTANDERS.
While all efforts have been made to ensure the accuracy of all information in this
manual, FUJITSU assumes no liability to any party for any damage caused by
errors or omissions or by statements of any kind in this manual, its updates or
supplements, whether such errors are omissions or statements resulting from
negligence, accidents, or any other cause. FUJITSU further assumes no liability
arising from the application or use of any product or system described herein; nor
any liability for incidental or consequential damages arising from the use of this
manual. FUJITSU disclaims all warranties regarding the information contained
herein, whether expressed, implied, or statutory.
FUJITSU reserves the right to make changes to any products herein, to improve
reliability, function, or design, without further notice and without obligation.

v
Preface
This manual explains how to use the M4097D image scanner.
This manual contains chapters on the following topics:
COMPONENTS
INSTALLATION AND CONNECTIONS
OPERATING INSTRUCTIONS
ADF DOCUMENT SPECIFICATIONS
SCANNER SPECFICATIONS
SETUP MODE
It also contains a Glossary of Terms and an Index.
Refer to Cleaning and Maintenance Guide for information about the routine
operation of the M4097D.
The Reference Guide contains chapters on OPERATING INSTRUCTIONS,
CLEANING,REPLACEMENTOFPARTS,ADJUSTMENTandTROUBLESHOOT-
ING.
The M4097D is a very fast and highly functional image scanner developed for
volume filing, using charge-coupled device (CCD) image sensors. This scanner
features duplex scanning and high quality image processing with an automatic
document feeder (ADF).

vi
Conventions
Important information that requires special attention is indicated as follows:
WARNING
WARNING indicates that personal injury like pinching of fingers or hands may
result if you do not follow a procedure correctly.
CAUTION
CAUTION indicates that damage to the scanner may result if you do not follow a
procedure correctly.
Official Fujitsu part names are indicated with an initial capital letter, as in the part
name “Pick roller”.
NOTICE
A NOTICE provides “how-to”tips or suggestions to help you perform a procedure
correctly.

viivii
CONTENTS
❑❑❑❑❑CHAPTER 1 COMPONENTS
Checking the Components ............................................. 1-1
Units and Assemblies ..................................................... 1-2
Operator Panel ............................................................... 1-5
❑❑
❑❑
❑CHAPTER 2 INSTALLATION AND CONNECTIONS
Precautions..................................................................... 2-1
Inspection ....................................................................... 2-2
Repositioning the Shipping Lock.....................................2-4
Cable Connections ......................................................... 2-5
Mounting the Stacker......................................................2-7
Setting the SCSI ID and the SCSI Terminator ............... 2-8
❑❑
❑❑
❑CHAPTER 3 OPERATING INSTRUCTION
Turning the Power On .................................................... 3-1
Waking up the Scanner from the Low Power Mode ....... 3-2
Manual Feed Mode Setting ............................................ 3-3
Loading Documents on the ADF .................................... 3-4
Loading Documents on the Flatbed................................ 3-9
Loading Documents Larger than the Document Bed.... 3-10
Reading a Page from a Thick Book.............................. 3-11
❑❑
❑❑
❑CHAPTER 4 ADF DOCUMENT SPECIFICATION
Document Size ............................................................... 4-1
Document Quality ........................................................... 4-2
ADF Document Feeder Capacity.................................... 4-4
Areas not to be Perforated ............................................. 4-5
Grounding Color Areas ................................................... 4-6
Double Feed Detection Condition................................... 4-7
Job Separation Sheet ..................................................... 4-8
❑❑
❑❑
❑CHAPTER 5 SCANNER SPECIFICATIONS
Basic Product Specification ............................................ 5-1
Installation Specification ................................................. 5-2
Dimensions..................................................................... 5-3
❑❑
❑❑
❑CHAPTER 6 CONSUMABLES AND OPTIONS
Consumables.................................................................. 6-1
Options ........................................................................... 6-2
VIDEO Interface Option.................................................. 6-3
IPC-4D Option ................................................................ 6-8

viii
❑❑
❑❑
❑CHAPTER 7 SETUP MODE
Activating the Setup Mode.............................................7-1
Contents of the Setup Mode........................................... 7-2
❑❑
❑❑
❑GLOSSARY OF TERMS ...................................................................... GL-1
❑❑
❑❑
❑INDEX ..................................................................................... IN-1
❑❑
❑❑
❑Declarations of Conformity................................................................ DE-1