Fujitsu PRIMERGY CX420 S1 User guide

PRIMERGY CX420 S1 / CX272 S1
System configurator and order-information guide
Contents
Instructions
Configuration diagram
Configurator
0 System software
I CX420 S1 Basic unit
II CX272 S1Basic unit
III Processor
IV Graphics
V Memory
VI Shared drive bay
VII OS boot drive bay
VIII Onboard SW RAID 0/1, additional HDD access option
IX Communication/Network
X System Management Products (RemoteView)
XI Miscellaneous
Change report
PRIMERGY Server
January 2014

System configurator and order-information guide
PRIMERGY CX420 S1 / CX272 S1 Status 2013-12-30
Instructions
This document contains basic product and configuration information that will enable you to configure your system via
PC-/System-Architect.
Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete
PRIMERGY Rack system.
You can configure your individual PRIMERGY server in order to adjust your specific requirements.
The System configurator is divided into several chapters that are identical to the current price list and PC-/SystemArchitect.
Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through
the configurator by following the lines from the top to the bottom.
Section
III Memory, example
There are X memory slots which can be equipped with XXX MB.
It is permissible to make up to X passes through the memory upgrade options
S26361-XXX-XXX S26361-XXX-XXX
Memory XXX MB
Memory XXX MB
X times
max. X times per system max. X times per system
In one chapter you can only select as many components (here 4x) as the arrow indicates. 4x
Please note that there are information symbols which indicate necessary information.
For further information see:
http://ts.fujitsu.com/products/standard_servers/index.html
(internet)
https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/current/Pages/default.aspx
(extranet)
Fujitsu Technology Solutions x86 PRIMERGY Serve 2 of 21

System configurator and order-information guide
PRIMERGY CX420 S1 / CX272 S1 Status 2013-12-30
Configuration diagram PRIMERGY CX420 S1
System unit ( I )
with up to 12x 3.5" or 2.5" for shared HDDs plus up to 2x internal HDD per node for OS boot HDDs
CX400 S1 3,5" HDD cage standard (S26361-K1461-V135)
Key:
Included in basic unit Option
Note: each CX420 S1 should install 2x CX272 S1 always
Each nodes are hot plugable and must be identical configuration
CX272 S1 half wide two U server node
PSU 1
PSU 2
Tray 1
Tray 2
Fujitsu Technology Solutions x86 PRIMERGY Serve 3 of 21

System configurator and order-information guide
PRIMERGY CX420 S1 / CX272 S1 Status 2013-12-30
Configuration diagram PRIMERGY CX272 S1
System unit ( I )
with up to 12x 3.5" or 2.5" HDDs for shared HDDs plus 2x internal HDDs for OS boot HDDs
Motherboard
CX400 Chassis parts
Memory CPU1
Rear side on each node
( Channel A + B + C + D )
2 USB
Bank 1 (2 Modules)
Xeon DP
1 VGA
Bank 2 (2 Modules)
2x LAN & Service LAN
Bank 3 (2 Modules) Rear side
Bank 4 (2 Modules)
Memory CPU2
1. PSU 2. PSU
( Channel E + F + G + H)
Bank 1 (2 Modules)
Xeon DP
Bank 2 (2 Modules) Hotplug power supply
Bank 3 (2 Modules)
Bank 4 (2 Modules)
Memory (III ) Processor ( II ) Inside
Fan 1 - Fan 4
PSAS CP200i (SAS HBA)
For up to 12x SAS/BC SAS/SAS SSD Non-Hotplug
LSI SW Raid, Raid 0 / 1
included in Chassis
Onboard for up to internal 2x SATA/SATA SSD
Front
Hard disk drives ( VI )
2.5"or3.5" SAS (shared HDD)
Slot 1 PCIe-3 x8, 390mm for PSAS CP200i Up to shared 12x SAS HDDs/SSD
can be installed
in CX420 S1 chassis
Slot 2 PCIe-3 x8, 390mm
2.5" SAS or dummy
2.5" SAS or dummy
Slot 3 PCIe-3 x8 for 10GbE card
2.5" SAS or dummy
2.5" SAS or dummy
2.5" SAS or dummy
2.5" SAS or dummy
2.5" SAS or dummy
2.5" SAS or dummy
2.5" SAS or dummy
2.5" SAS or dummy
2.5" SAS or dummy
2.5" SAS or dummy
Hard disk drives ( VI )
2.5" SATA (OS boot)
Up to 2 SATA HDDs/SSD
can be installed
in CX272 S1 node
2.5" SATA
2.5" SATA
Key:
Included in basic unit Option
The population order for the CPU is: CPU1 first, then CPU2
Fujitsu Technology Solutions x86 PRIMERGY Serve 4 of 21

PRIMERGY-Software Configurators and Release Lists
Start PRIMERGY CX250 S1 / CX270 S1
PRIMERGY CX420 S1 / CX272 S1 Status 2013-12-30
Section
O SW Configurator 64 bit (EM64T / IA64)
with OEM-Software without OEM-Software
for PRIMERGY Server for PRIMERGY Server
OEM- SW is bound to HW and
For all SW products please refer to the corresponding
is not allowed to be ordered
software configurator accessible via the Extranet under separately.
"Configuration & Tools, -All configurations, -Software, Exceptions: VMware SW,
URL see below. Citrix XenServer
Microsoft Hyper-V Server and System Center
- Microsoft Hyper-V Server 2012
Microsoft - Windows Server 2012
Microsoft - Windows Storage Server 2012
- Windows Server 2012 Datacenter
- Windows Server 2012 Standard
**) Pay attention to release and order information in PRINCE -> Operating System
https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
***) Supply over distribution or procurement from FSC VP BC Software
You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:
for internal users: http://sp.ts.fujitsu.com/dmsp/docs/osrel.xlsx
for partners:
https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
Continue with PRIMERGY
HW configurator
Fujitsu Technology Solutions x86 PRIMERGY Server

System configurator and order-information guide
Start PRIMERGY CX400 S1
PRIMERGY CX420 S1 / CX272 S1 Status 2013-12-30
Section
IBasic unit
System unit consisting of:
* 2U Housing with power supply modules, Rack Rails and HDD cages
* Basic units with:
- 2 Hot-Plug Power Supply rated 1,200W
- 4 non-hot plug Fans (redundancy)
* Dual port SAS Backplane for 12x 3.5"or 2.5" HD
* Drives/Bays
- 12 bays 1" for hot plug 3.5"/2.5" HD
- SAS I/F HDD or SSD supported
- HDD configuration per Server node
- empty bays will be covered with dummy frames
* Server nodes
- each CX420 S1 can support 2x CX272 S1
- position of CX server nodes fixed
Software:
* ServerView Suite Software
* Documentation engl. (multilingual on CD)
A
Fujitsu Technology Solutions x86 PRIMERGY Serve 6 of 21

System configurator and order-information guide
APRIMERGY CX420 S1 / CX272 S1 Status 2013-12-30
Rack version for 19'' racks with
PSU included in Base Unit
Basic unit with
12x 3,5" HDD cage S26361-K1461-V135
2x 1200W PSU module One 1200W power supply module hot plug No loose delivery
100-240V wide range no power cable included!!!
94% efficiency (Platinum) 200-240V environment: Full AC redundancy is available.
100V environment: System performance adjusted, when only one
PSU is in operation
Please order appropriate power cord additionally:
Powercord for rack, 4m, grey, IEC320 C13->C14 connector
T26139-Y1968-L10
Power Cord USA / Canada, 1.8m, grey
T26139-Y1742-L10
B
Fujitsu Technology Solutions x86 PRIMERGY Serve 7 of 21

System configurator and order-information guide
B
PRIMERGY CX420 S1 / CX272 S1 Status 2013-12-30
PRIMECENTER Rack
Sliding rail
1-hand-mounting
RMK - 1 pair consisting of
-
carrier length variable S26361-F4530-L12
toolless mounting possible
Adapter angle PC/DC-Rack, till 50Kg
necessary for mounting RMKs in
asymmetrical racks
included in base unit
S26361-F4530-E12
S26361-F4530-E10
Mounting 2U server in Mounting in
asymmetrical racks symmetrical & 3rd party racks
with 2U support bracket (no support bracket needed)
SNP:SY-F1647E301-P
Installation ex works for one
server or subsystem.
Hereby the rack will be delivered "Rack-mounting ex factory"
completely pre-mounted and
This service is to be ordered once
all wired connections are tested.
per installable server/storage
With PCR S2 12U, 24U, 38U and subsystem, in order to get the
PRC M1 16U, 24U, 42U: server/storage subsystem
Systems and components mounted into the racks.
will be delivered installed in the rack In case of the 46 U PCR S2
With PCR S2 racks 46U: this service has to be ordered,
Systems and components to get the mounting kits and the
will be delivered separately cables installed.
To be ordered only together with
a PRIMECENTER rack
PCR S2 e.g. S26361-K826-V10x
new PCR M1 e.g. S26361-K827-Vxxx
refer PCR S2 or M1 rack configurator
max. 1x per System PRIMERGY Classic 19" rack is not supported
S26361-F1452-E100
S26361-F1452-E110
REGION KIT EMEA AP REGION KIT JP
For Shipments to EMEA / Asia and For Shipments to Japan regions
Pacific regions
1x per system
1x per system
Power cord has to be ordered separately
Power cord options (1x per PSU)
T26139-Y1968-E100 Powercord for rack, 4m, grey,
IEC 320 C14 connector
2x
T26139-Y1742-E10
USA, Canada, 1.8m, grey
T26139-Y3850-E10
Option "no powercord", for Countries without
specific cable orderable like e.g. China
C
Fujitsu Technology Solutions x86 PRIMERGY Serve 8 of 21

System configurator and order-information guide
Start PRIMERGY CX272 S1
PRIMERGY CX420 S1 / CX272 S1 Status 2013-12-30
Section
II Basic unit
CX272 S1 System unit consisting of:
* 2U half wide server node (tray & motherboard) for pluggin into CX420 chassis
* Basic units with:
- Server tray mechanics
- Motherboard
- 1x PCIe- x8 slots for PSAS CP200i
- 1x PCIe- x8 GEN3 low profile
- 1x PCIe- x8 GEN3 low profile (only for 10GbE D2755 and 10GbE-T card)
Systemboard D3306 with:
* Up to two Xeon 4C, 6C & 8C CPU`s (Socket-R)
with 2 serial QPI links ( Quick Path Interconnect ) and four memory channels per CPU
CPU has to be selected for an orderable basic unit,
* Chipset Intel® C600 Series
* number of PCI slots: see above
* 16 memory slots for max. 512GB RAM DDR3 available
- Memory is divided into 8 DIMMs per CPU ( 4 channels with 2 slots per channel )
Possible max. configurations are:
16x 16GB RDIMM (dual rank modules) = 256GB
16x 4GB UDIMM (dual rank modules) = 64GB
First Memory ( one module ) has to be selected for an orderable basic unit per CPU
- Memory upgrade is possible by 8x memory units
- SDDC (Chipkill) is supported for memory modules,
* Dual Port 10/100/1000 x4 PCI Express* Gigabit Ethernet Intel LAN controller Powerville on-board
* AST2300 (integrated Baseborad Management Controller) on-board server management controller with
dedicated 10/100 Service LAN-port and integrated graphics controller.
The Service LAN-port can be switched alternatively on standard Gbit LAN port
* Graphics Controller integrated in AST2300 (integrated Baseboard Management Controller):
1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz,
640x480x32bpp 85Hz
Interfaces at the rear:
* 1x RS-232-C (serial, 9 pins)
* 1x VGA (15 pins)
* 2x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup
* 2x LAN RJ45, 1x Service-LAN RJ45
Interfaces internal:
* 1x USB 2.0 for UFM modul (embeded ESXi)
* 6x SATA interface via Patsburg -A for 6 SATA HD`s Non-Raid or 4 SATA HD's Raid 0/1/10 (LSI SW Raid)
A
Fujitsu Technology Solutions x86 PRIMERGY Serve 9 of 21

System configurator and order-information guide
APRIMERGY CX420 S1 / CX272 S1 Status 2013-12-30
Server node for CX400 S1 2U chassis
PSU is part of CX400 S1 Base Unit
Basic unit is without CPU and Memory
Non fully ocupied configuration is not supported
For an orderable basic unit two CPU always
CX272 S1 Basic unit
PRIMERGY CX272 S1 S26361-K1465-V300 CX420 S1 with 2x CX272 S1
S26361-K1465-V300
PRIMERGY CX272 S1
2U half wide
INTEL Processor 2x
for CX272 S1
Each CX272 S1 configuration to be identical
based dual socket Server Blade.
Always 2x per system unit
S26361-F4575-E10
Service for CX-Server nodes
installation in the CX420 12x 3.5"
max. 2x per system unit
B
Server#1Server#2
Fujitsu Technology Solutions x86 PRIMERGY Serve 10 of 21