Fujitsu GP 7000F User manual

Edition December 1999
GP 7000F
M200, M200R, M400A, M400R, M600,M600R

CopyrightandTrademarks
Copyright©FujitsuSiemensComputersGmbH1999.
Allrightsreserved.
Deliverysubjecttoavailability;rightoftechnicalmodificationsreserved.
Allhardwareandsoftwarenamesusedaretrademarksoftheirrespectivemanufacturers.

U42335-J-Z775-1-76 1
1 Preface
ThismanualcontainstheoperatinginstructionsfortheGranPower7000(GP7000F)system
from Fujitsu Siemens Computers. A chapter about the connection of Siemens specific de-
vices precedes the actual operating instructions.

U42335-J-Z775-1-76 3
2 Console connections to GP 7000F
This chapter describes connections to the M200, M200R, M400A, M400R, M600 and
M600R models of the Fujitsu Siemens Computers GP 7000F system with a view to
attachingexistingcomponentsofSiemensdevicestoFujitsuequipment.Graphicalor serial
consoles can be connected.
The GP 7000F systems do not support SIDATA
(installation by customer is not allowed).
2.1 Graphical console
It is preferable to connect graphical consoles.
!
system
GP 7000F
V.24 (B)
V.24 (A)
10/100 Mbit Eth
Monitor
Keyboard/mouse
PCI graphics
controller
D:GP70F-CC10
(option)
SUNAdapt
Keyboard Mouse
Teleservice
preferably
(Keyboard with trackball
in the 19" rack)

Graphical console Console connections to GP 7000F
4U42335-J-Z775-1-76
The following technical requirements must be met in order to connect graphical consoles:
– PCI graphics controller D:GP70F-CC10
The GP 7000F models can be made into a workstation or server with a graphical
console by means of a PCI graphics card featuring a frame buffer.
– An RM keyboard and mouse can be connected via the D:GP70F-AN10 interface
converter. All models in the GP 7000F server family have a Sun-compatible
keyboard/mouse interface. The adapter converts the interface signals to allow the
keyboard and 3-button mouse featuring a PC-compatible interface to be connected
to the server.
Keyboard/mouse adapter
– Monitor (CRT or LCD)
– Keyboard
–Mouse
The same monitor, keyboard and mouse types have been released as for the Siemens
systems.
PS/2 M aus
PS/2 Tastatur
SUN-
Tastatur/M aus-
Schnittstelle
PS/2 mouse
PS/2 keyboard
Sun keyboard/
mouse interface

Console connections to GP 7000F Serial console
U42335-J-Z775-1-76 5
2.2 Serial console
A converter is used here to convert the 25-pin connector of the GP 7000F system to the
usual 9-pin V.24/COM connector. This converter is preinstalled at the factory. A VT100 or
VT200 emulation must be available for a serial console to be used.
25/9-pin converter
9polig
V.24/C O M
25polig
Dsub
9-pin
25-pin

Serial console Console connections to GP 7000F
6U42335-J-Z775-1-76
2.2.1 LAN console
ASolarisPCisconnectedas aLANconsolevia an RCA(RemoteCommunicationAdapter)
attached to the V.24 console interface. Up to six servers can be attached to one RCA.
RCA
system
GP 7000F
V.24 (B)
V.24 (A)
10/100 Mbit Eth
Keyboard/mouse
LAN
console
Ethernet hub
Teleservice

Console connections to GP 7000F Serial console
U42335-J-Z775-1-76 7
2.2.2 Standard PC with terminal emulation
a) Windows 98 or NT (with NetTerm, for instance, but not with HyperTerminal)
b) LINUX (with Minicom or Seyon)
c) Solaris (cu)
system
GP 7000F
V.24 (B)
V.24 (A)
10/100 Mbit Eth
Keyboard/mouse
PC
(NT, Windows)
preferably
Teleservice

Teleservice Console connections to GP 7000F
8U42335-J-Z775-1-76
2.2.3 TC20 or T100
Use of these terminals is intended as a migration solution only.
When operating with theLAN console, TC20 orT100 it isnot possibleto access the
Open Boot PROM using the BREAK signal.
2.3 Teleservice
The teleservice modem has to be connected via V.24 to the system board. The modem has
to be ordered separately owing to national variants.
If a LAN console is used, connection of the modem is to the LAN console PC. Thus one
teleservice port serves all connected servers.
GP 7000F
system
V.24 (B)
V.24 (A)
10/100 Mbit Eth
Keyboard/mouse
α
αα
αconsole
preferably
Teleservice
i