Fujitsu PRIMERGY TX1330 M4 User manual

FUJITSU Server PRIMERGY TX1330 M4
Upgrade and Maintenance Manual
Upgrade and Maintenance Manual - English
04/2022

Comments… Suggestions… Corrections…
The User Documentation Department would like to know your opinion of this manual. Your
feedback helps us optimize our documentation to suit your individual needs.
Feel free to send us your comments by e-mail to [email protected].
Documentation creation according to ISO 9001 and ISO 27001
To ensure high quality and information security standards while creating documentation, the
quality management system and information security management system of cognitas are
certified in compliance with ISO 9001 and ISO 27001.
cognitas. Gesellschaft für Technik-Dokumentation mbH www.cognitas.de/en/
Copyright and Trademarks
Copyright 2022 FUJITSU LIMITED
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
–The contents of this manual may be revised without prior notice.
–Fujitsu assumes no liability for damages to third party copyrights or other rights arising from
the use of any information in this manual.
–No part of this manual may be reproduced in any form without the prior written permission
of Fujitsu.
Microsoft, Windows, Windows Server, and Hyper-V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.

Before reading this manual
For your safety
This manual contains important information for safely and correctly using this
product.
Carefully read the manual before using this product. Pay particular attention to
the accompanying manual "Safety Notes and Regulations" and ensure that
these safety notes are understood before using the product. Keep this manual
and the "Safety Notes and Regulations" manual in a safe place for easy
reference while using this product.
Radio interference
This product is a "Class A" ITE (Information Technology Equipment). In a
domestic environment this product may cause radio interference, in which case
the user may be required to take appropriate measures.
VCCI-A
Aluminum electrolytic capacitors
The aluminum electrolytic capacitors used in the printed circuit board
assemblies of the product and in the mouse and keyboard are limited-life
components. Use of these components beyond their operating life may result
in electrolyte leakage or depletion, potentially causing emission of foul odor or
smoke.
As a guideline, in a normal office environment (25 °C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the
product is used in a hot environment. The customer shall bear the cost of
replacing replaceable components which have exceeded their operating life.
Note that these are only guidelines, and do not constitute a guarantee of
trouble-free operation during the maintenance support period.
High safety use
This product has been designed and manufactured to be used in commercial
and/or industrial areas as a server.
TX1330 M4 Upgrade and Maintenance Manual

The product is not suitable for use at visual display workplaces according to §2
of the Workplace Regulations (applies to all server systems except TX server
systems).
When used as visual display workplace, it must not be placed in the direct field
of view to avoid incommoding reflections (applies only to TX server systems).
The device has not been designed or manufactured for uses which demand an
extremely high level of safety and carry a direct and serious risk of life or body
if such safety cannot be assured.
These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance
control in weapons systems (hereafter, "high safety use"). Customers should
not use this product for high safety use unless measures are in place for
ensuring the level of safety demanded of such use. Please consult the sales
staff of Fujitsu if intending to use this product for high safety use.
Measures against momentary voltage drop
This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, the use of an
uninterruptible power supply is recommended.
(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)
Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan
Documents produced by Fujitsu may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.
Harmonic Current Standards
This product conforms to harmonic current standard JIS C 61000-3-2.
Upgrade and Maintenance Manual TX1330 M4

Only for Japan: About SATA HDDs
The SATA version of this server supports HDDs with SATA/BC-SATA storage
interfaces. Please note that the usage and operation conditions differ
depending on the type of HDD used.
For more information on the usage and operation conditions of each available
type of HDD, see the following internet address:
https://jp.fujitsu.com/platform/server/primergy/harddisk/
Only for Japan:
Shielded LAN cables should be used in this product.
UK Importer information
Fujitsu Services Limited
22 Baker Street, London, W1U 3BW, United Kingdom
TX1330 M4 Upgrade and Maintenance Manual

Version history
Issue
number
Issue date Description
V 1.0 11/2018 Initial release
V 2.0 09/2019 New text Chassis ID Prom Tool, new CPU types
V 3.0 12/2020 Cable plan updated
V 4.0 04/2021 – Verifying system information backup/restore
–Replacing the CMOS battery
– Replacing the system board
10/2021 – Some structures adepted to new editoral
system
– Information about Infrastructure Manager
(ISM) added
V 5.0 04/2022 – Cable plan updated
– List of released adapters updated
Upgrade and Maintenance Manual TX1330 M4

Content
1 Introduction 19
1.1 Concept and target groups of this manual 19
1.2 Notational conventions 19
2 Before you start 21
2.1 Basic information 21
2.1.1 Proceeding 21
2.1.2 Advanced Thermal Design (ATD) 21
2.1.3 Installing optional components 22
2.1.4 Replacing a defective component 22
2.2 Classification of procedures 23
2.2.1 Assignment of unit categories 23
2.2.2 Customer Replaceable Units (CRU) 23
2.2.3 Upgrade and Repair Units (URU) 24
2.2.4 Field Replaceable Units (FRU) 25
2.3 Average task duration 27
2.4 Tools you need at hand 28
2.5 Documentation overview 28
2.5.1 About availability of manuals 28
2.5.2 List of documents 28
3 Important information 31
3.1 Introduction 31
3.2 Safety instructions 31
3.2.1 Basic safety instructions 31
3.2.2 Before starting up 32
TX1330 M4 Upgrade and Maintenance Manual

3.2.3 Installation and operation 32
3.2.4 Batteries 35
3.2.5 Working with optical disk drives (ODDs) and media 35
3.2.6 Laser information 37
3.2.7 Modules with Electrostatic-Sensitive Devices (ESD modules) 37
3.2.8 Transporting the server 39
3.2.9 Installing the server in the rack 40
3.2.10 Other important information 40
3.3 ENERGY STAR 41
3.4 CE conformity 41
3.5 FCC Class A Compliance Statement 42
3.6 Environmental protection 43
4 Basic hardware procedures 45
4.1 Using diagnostic information 45
4.1.1 Proceeding 45
4.1.2 Locating the defective server 45
4.1.3 Determining the error class 46
4.1.4 Locating the defective component 46
4.2 Shutting down the server 47
4.3 Disconnecting the power cord 48
4.3.1 Disconnecting the power cord (standard PSU) 48
4.3.2 Disconnecting the power cord (hot-plug PSU) 49
4.4 Getting access to the component 50
4.4.1 Safety notes 50
4.4.2 Rack model 50
4.4.2.1 Extending the server out of the rack 50
4.4.2.2 Removing the server from the rack 51
4.4.2.3 Removing the top cover 54
4.4.2.4 Removing the rack front cover 55
4.4.3 Floorstand model 58
Content
Upgrade and Maintenance Manual TX1330 M4

4.4.3.1 Unlocking the server 58
4.4.3.2 Removing the side cover 60
4.4.3.3 Removing the accessible drive bay cover 61
4.4.3.4 Removing the HDD bay cover 63
4.4.3.5 Removing the front cover 63
4.5 Reassembling 66
4.5.1 Safety notes 66
4.5.2 Rack model 66
4.5.2.1 Installing the rack front cover 66
4.5.2.2 Installing the top cover 68
4.5.2.3 Installing the server in the rack 69
4.5.2.4 Sliding the server into the rack 72
4.5.3 Floorstand model 73
4.5.3.1 Installing the front cover 73
4.5.3.2 Installing the HDD bay cover 75
4.5.3.3 Installing the accessible drive bay cover 76
4.5.3.4 Installing the side cover 77
4.5.3.5 Locking the server 78
4.6 Connecting the power cord 79
4.6.1 Connecting the power cord (standard PSU) 79
4.6.2 Connecting the power cord (hot-plug PSU) 80
4.7 Switching on the server 81
4.8 Handling the system fan module 82
4.8.1 Removing the system fan module 82
4.8.2 Installing the system fan module 85
4.9 Handling accessible drive bays 89
4.9.1 Opening the accessible drive locking bar 89
4.9.2 Closing the accessible drive locking bar 91
4.9.3 Accessible drive filler covers 92
4.9.3.1 Removing accessible drive filler covers 92
4.9.3.2 Installing accessible drive filler covers 93
4.9.4 Accessible drive covers 95
4.9.4.1 Removing accessible drive covers 95
4.9.4.2 Installing accessible drive covers 96
Content
TX1330 M4 Upgrade and Maintenance Manual

4.10 Handling the anti-tilt bracket 97
4.10.1 Installing the anti-tilt bracket 97
4.10.2 Removing the anti-tilt bracket 98
5 Basic software procedures 99
5.1 Validation 99
5.2 Starting the maintenance task 99
5.2.1 Suspending BitLocker functionality 99
5.2.2 Disabling the boot watchdog 100
5.2.3 Removing backup and optical disk media 102
5.2.4 Verifying and configuring the backup software solution 102
5.2.5 Switching on the ID indicator 102
5.3 Completing the maintenance task 103
5.3.1 Updating or recovering the BIOS and iRMC S5 103
5.3.2 Verifying system information backup or restore 105
5.3.3 Updating expansion card firmware 106
5.3.4 Enabling Option ROM scan 107
5.3.5 Reconfiguring the backup software solution 108
5.3.6 Resetting the boot retry counter 108
5.3.7 Resetting the error status after replacing memory modules or
CPUs 110
5.3.7.1 Resetting the error status after replacing memory modules 110
5.3.7.2 Resetting the error status after replacing CPUs 112
5.3.8 Enabling the boot watchdog 114
5.3.9 Enabling replaced components in the BIOS 115
5.3.10 Verifying the memory mode 116
5.3.11 Verifying the system time settings 116
5.3.12 Viewing and clearing the System Event Log (SEL) 117
5.3.13 Updating the NIC configuration file in a Linux and VMware
environment 120
5.3.14 Resuming BitLocker functionality 121
5.3.15 Performing a RAID array rebuild 122
5.3.16 Looking for MAC/WWN/GUID and SAS addresses 123
5.3.16.1 Basic information 123
5.3.16.2 Looking for the MAC address of a LAN controller 123
5.3.16.3 Looking for the WWN address of a fibre channel controller 124
Content
Upgrade and Maintenance Manual TX1330 M4

5.3.16.4 Looking for the GUID address of an infiniband or Omni-Path
controller 125
5.3.16.5 Looking for SAS addresses of SAS controllers for external
devices 125
5.3.17 Using the Chassis ID Prom Tool 126
5.3.18 Configuring LAN teaming 128
5.3.19 Switching off the ID indicator 129
5.3.20 Performing a fan test 130
5.3.21 Specifying the chassis model 131
6 Power supply unit (PSU) 133
6.1 Safety notes 133
6.2 Basic information 133
6.3 Standard power supply 135
6.3.1 Replacing the standard PSU 135
6.4 Redundant power supply 145
6.4.1 Installing a hot-plug PSU 145
6.4.2 Removing a hot-plug PSU 148
6.4.3 Replacing a hot-plug PSU 152
6.4.4 Replacing the power distribution board 154
6.5 Fujitsu battery unit (FJBU) 159
6.5.1 Installing an FJBU 159
6.5.2 Removing an FJBU 161
6.5.3 Replacing an FJBU 163
6.6 Converting a standard power supply to a redundant power
supply 164
7 Hard disk drive (HDD) / solid state disk (SSD) 169
7.1 Safety notes 169
7.2 Basic information 170
Content
TX1330 M4 Upgrade and Maintenance Manual

7.3 Handling HDDs or SSDs without installation frame 175
7.3.1 2.5-inch HDD/SSD and 2.5-inch installation frame 175
7.3.2 2.5-inch HDD/SSD and 3.5-inch installation frame 177
7.3.3 3.5-inch HDD and 3.5-inch installation frame 178
7.4 3.5-inch HDD configurations 181
7.4.1 Equipping the 3.5-inch HDD bays 181
7.4.2 Overview of configurations 181
7.4.2.1 Configuration with up to four HDD modules 181
7.4.2.2 Configuration with up to eight HDD modules 182
7.4.2.3 Configuration with up to 12 HDD modules 183
7.4.2.4 Configuration with additional PCIe SSD modules 184
7.4.3 Installing 3.5-inch HDD modules 185
7.4.4 Removing 3.5-inch HDD modules 188
7.4.5 Replacing a 3.5-inch HDD module 190
7.4.6 Replacing a 3.5-inch HDD backplane 192
7.4.7 Upgrading configuration from up to four to up to eight 3.5-inch
HDDs 203
7.5 2.5-inch HDD/SSD configurations 209
7.5.1 Overview of configurations 209
7.5.1.1 Configurations with up to eight HDD/SSD modules 209
7.5.1.2 Configurations with up to 16 HDD/SSD modules 210
7.5.1.3 Configurations with up to 24 HDD/SSD modules 211
7.5.1.4 Configurations with additional PCIe SSD modules 213
7.5.2 Installing 2.5-inch HDD/SSD modules 214
7.5.3 Removing 2.5-inch HDD/SSD modules 216
7.5.4 Replacing a 2.5-inch HDD/SSD module 219
7.5.5 Replacing a 2.5-inch HDD backplane 221
7.5.6 Upgrading configuration from eight to 16 2.5-inch HDDs/SSDs 236
7.6 HDD extension box 241
7.6.1 Installing the 8x 2.5-inch HDD/SSD extension box 241
7.6.2 Removing the 8x 2.5-inch HDD/SSD extension box 247
7.6.3 Replacing the HDD/SSD backplane or PCIe SSD on the 8x 2.5-
inch HDD/SSD extension box 250
7.6.4 Installing the 4x 3.5-inch HDD extension box 256
7.6.5 Removing the 4x 3.5-inch HDD extension box 260
Content
Upgrade and Maintenance Manual TX1330 M4

7.6.6 Replacing the HDD backplane on the 4x 3.5-inch HDD extension
box 262
7.7 SAS expander board 268
7.7.1 Installing the SAS expander board 268
7.7.2 Removing the SAS expander board 273
7.7.3 Replacing the SAS expander board 275
8 Fans 277
8.1 Safety notes 277
8.2 Basic information 277
8.3 Replacing the system fan 279
9 Expansion cards and backup units 287
9.1 Safety notes 287
9.2 Basic information 287
9.3 Handling slot brackets 289
9.3.1 Installing slot brackets 289
9.3.2 Removing slot brackets 290
9.4 Handling SFP+ transceiver modules 291
9.4.1 Installing SFP+ transceiver modules 291
9.4.2 Removing SFP+ transceiver modules 296
9.5 Expansion cards and riser cards 299
9.5.1 Installing an expansion card 299
9.5.2 Removing an expansion card 305
9.5.3 Replacing an expansion card 308
9.5.4 Replacing a riser card 310
9.5.5 Replacing a TFM 313
9.6 Flash backup unit (FBU) 318
9.6.1 Positions of the FBUs 318
Content
TX1330 M4 Upgrade and Maintenance Manual

9.6.2 Installing an FBU 319
9.6.3 Removing an FBU 324
9.6.4 Replacing an FBU 328
10 Main memory 331
10.1 Safety notes 331
10.2 Basic information 332
10.2.1 Slots and features 332
10.2.2 General memory population rules 332
10.2.3 Modes of operation 333
10.3 Installing memory modules 333
10.4 Removing memory modules 336
10.5 Replacing memory modules 338
11 Processor (CPU) 341
11.1 Safety notes 341
11.2 Basic information 341
11.3 Upgrading or replacing the CPU 342
11.4 Replacing the heat sink 353
11.5 Handling the protectice cover 355
12 Accessible drives 361
12.1 Safety notes 361
12.2 Basic information 361
12.3 Installing accessible drives 364
Content
Upgrade and Maintenance Manual TX1330 M4

12.4 Removing accessible drives 370
12.5 Replacing accessible drives 372
12.6 Slimline ODD in Multibay box 373
12.6.1 Installing the slimline ODD 373
12.6.2 Removing the slimline ODD 378
12.6.3 Replacing the slimline ODD 383
12.7 Ultraslim ODD in 3.5-inch HDD extension box 384
12.7.1 Installing the ultraslim ODD 384
12.7.2 Removing the ultraslim ODD 390
12.7.3 Replacing the ultraslim ODD 393
12.8 Ultraslim ODD in an ultraslim ODD adapter 394
12.8.1 Installing the ultraslim ODD 394
12.8.2 Removing the ultraslim ODD 398
12.8.3 Replacing the ultraslim ODD 400
13 Front panel 403
13.1 Safety notes 403
13.2 Replacing the front panel module 403
14 System board and components 413
14.1 Safety notes 413
14.2 Basic information 413
14.3 CMOS battery 414
14.3.1 Replacing the CMOS battery 414
14.4 Trusted Platform Module (TPM) 417
14.4.1 TPM kit 417
14.4.2 Installing the TPM 417
14.4.3 Removing the TPM 421
14.4.4 Replacing the TPM 425
Content
TX1330 M4 Upgrade and Maintenance Manual

14.5 iRMC microSD card 427
14.5.1 Note for embedded Lifecycle Management (eLCM) 427
14.5.2 Installing the iRMC microSD card 427
14.5.3 Removing the iRMC microSD card 429
14.5.4 Replacing the iRMC microSD card 431
14.6 M.2 SSD 432
14.6.1 Slots and bolts for M.2 SSDs 432
14.6.2 Installing an M.2 SSD 433
14.6.3 Removing an M.2 SSD 437
14.6.4 Replacing an M.2 SSD 439
14.7 Dual microSD 64GB Enterprise 440
14.7.1 Position of the Dual microSD 64GB Enterprise 440
14.7.2 Installing the Dual microSD 64GB Enterprise 441
14.7.3 Removing the Dual microSD 64GB Enterprise 443
14.7.4 Replacing the Dual microSD 64GB Enterprise 445
14.7.5 Replacing the microSD card 447
14.8 System board 449
14.8.1 Replacing the system board 449
15 Converting a floorstand model to a rack model 459
16 Cabling 475
16.1 Replacing the intrusion switch cable 475
17 Appendix A 487
17.1 Mechanical overview 487
17.1.1 Server front 487
17.1.1.1 2.5-inch HDD/SSD model 487
17.1.1.2 3.5-inch HDD model 488
17.1.2 Server rear 490
17.1.2.1 Server rear with standard PSU 490
Content
Upgrade and Maintenance Manual TX1330 M4

17.1.2.2 Server rear with hot-plug PSUs 491
17.1.3 Server interior 492
17.1.3.1 Server with standard PSU 492
17.1.3.2 Server with hot-plug PSUs 493
17.2 Connectors and indicators 494
17.2.1 Connectors and indicators on the system board 494
17.2.1.1 Connectors and indicators on the system board 494
17.2.2 Server front 499
17.2.2.1 Connectors on the front panel 499
17.2.2.2 Indicators on the front panel 500
17.2.2.3 Indicator on the ODD 503
17.2.2.4 Indicators on the hot-plug HDD/SSD module 504
17.2.3 Server rear 506
17.2.3.1 Connectors on the server rear 506
17.2.3.2 ID, CSS and Global Error indicators 507
17.2.3.3 LAN indicators 509
17.2.3.4 Indicator on hot-plug PSU 511
17.2.3.5 Indicator on FJBU 512
17.2.4 Acoustic indicators 513
17.3 Onboard settings 515
17.4 Minimum startup configuration 516
18 Appendix B 519
18.1 Supplied documents 519
Content
TX1330 M4 Upgrade and Maintenance Manual

Content
Upgrade and Maintenance Manual TX1330 M4

1 Introduction
1.1 Concept and target groups of this manual
This upgrade and maintenance manual provides instructions for the following
procedures:
–Upgrading the server configuration by adding optional hardware
components.
–Upgrading the server configuration by replacing existing hardware
components with superior ones.
–Replacing defective hardware components.
This manual focuses on on-site maintenance tasks. It is recommended to
prepare each service assignment following remote diagnostics procedures, as
described in the "ServerView Suite Local Service Concept (LSC)" manual, see
"Documentation overview" on page 28.
CAUTION
The document at hand comprises procedures of a wide range of
complexity.
▶Check the profile of qualification for technicians before assigning
tasks.
▶Before you start, carefully read "Classification of procedures" on
page 23.
1.2 Notational conventions
The following notational conventions are used in this manual:
Text in bold Indicates references to names of interface
elements.
Text in monospace Indicates commands and text to be entered by
the user.
TX1330 M4 Upgrade and Maintenance Manual 19

"Quotation marks" Indicate names of chapters and terms that are
being emphasized.
▶ Describes activities that must be performed in
the order shown.
[Abc] Indicates keys on the keyboard.
CAUTION
Pay particular attention to texts marked with this
symbol. Failure to observe this warning may
endanger your life, destroy the system or lead
to the loss of data.
Indicates additional information, notes and tips.
Indicates the procedure category in terms of
complexity and qualification requirements, see
"Classification of procedures" on page 23.
Indicates the average task duration, see
"Average task duration" on page 27.
Introduction
20 Upgrade and Maintenance Manual TX1330 M4