Fujitsu PRIMERGY Econel 50 Owner's manual

PRIMERGY
PRIMERGY Econel 50
Server System
Service Supplement
Xenia Fierley
Fujitsu Siemens Computers GmbH München
81730 München
e-mail: email: [email protected]
Tel.: [phone]
Fax: 0 700 / 372 00000
Econel 50
Sprachen: De
Edition January 2005

This manual is printed on
paper treated with
chlorine-free bleach.
Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Fax forms for sending us your comments are included in
the back of the manual.
There you will also find the addresses of the relevant
User Documentation Department.
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademar s
Copyright © 2004 Fujitsu Siemens Computers GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.

Econel 50 Service Supplement
Contents
1Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Overview of the Documentation . . . . . . . . . . . . . . . . . . 1
1.2 Notational Conventions . . . . . . . . . . . . . . . . . . . . . . 3
2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4 Replacement Routines . . . . . . . . . . . . . . . . . . . . . 13
4.1 General Purposes . . . . . . . . . . . . . . . . . . . . . . . . 13
4.1.1 Removing/Mounting the Side Cover . . . . . . . . . . . . . . . 13
4.1.2 Removing/Mounting the Front Panel . . . . . . . . . . . . . . . 14
4.1.3 Removing/Mounting the System Fan . . . . . . . . . . . . . . 14
4.1.4 Fold out the Power Supply Unit . . . . . . . . . . . . . . . . . 14
4.1.5 Removing/Mounting the Cross-beam . . . . . . . . . . . . . . 16
4.2 Replacing the Operating Panel Cable . . . . . . . . . . . . . . 17
4.3 Replacing the Floppy Disk Drive . . . . . . . . . . . . . . . . . 19
4.4 Replacing the USB Connector Cable . . . . . . . . . . . . . . 21
4.5 Replacing the Power Supply Unit . . . . . . . . . . . . . . . . 23
4.6 Replacing the Intrusion Detection Switch . . . . . . . . . . . . 28
4.7 Replacing the System Board . . . . . . . . . . . . . . . . . . 30
5 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
5.1 Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Econel 50 Service Supplement 1
1 Introduction
The PRIMERGY Econel 50 server is an Intel-based server for small and mid-
size networks. The server is suitable for use as a file server and also as an appli-
cation, information or Internet server.
1.1 Overview of the Documentation
Concept and target group of this manual
This Service Supplement completes the information given in the Operating
Manual, the Options Guide and the Technical Manual of the system board.
The actions described in this manual should only be performed by service
personnel.
Service CD
Service partners of Fujitsu Siemens can order a Service CD. On the CD the
following manuals are available in PDF format:
– “Safety” manual
– Operating Manual for PRIMERGY Econel 50
– Technical Manual for the system board D1859
– Options Guide for PRIMERGY Econel 50
– Service Supplement PRIMERGY Econel 50
– “BIOS Setup” manual

2 Service Supplement Econel 50
Overview of the Documentation Introduction
Information/procedure Manual
Detailed safety notes Safety
Features and technical data of the server Operating Manual
Installation and operation, among other things:
– Operation
– Configuration of the server
Troubleshooting
Information about the system board:
– Features of the system board
– External ports on the server
– Pin assignment of the connectors
– Jumper settings
– LED indicators
– Replacing the battery
Technical Manual
Extensions and upgrades:
– Extending/replacing the main memory
– Installing the processor/replacing the
processor/replacing the heat sink
Technical Manual
IFor some components only the installation
routine is described in the Options Guide.
Removing these components proceed in
reverse order.
– Installing accessible drives
– Removing/installing the system fan
– Installing SATA hard disk drives
– Installing controllers in PCI slots
Options Guide
Replacement routines:
– Replacing the operating panel cable
– Replacing the floppy disk drive
– Replacing the USB cable (front)
– Replacing the power supply unit
– Replacing the intrusion switch
– Replacing the system board
Service Supplement
BIOS setup BIOS Setup
Table 1: Overview of the Documentation Econel 50

Econel 50 Service Supplement 3
Introduction Notational Conventions
1.2 Notational Conventions
The following notational conventions are used in this manual:
text in italics indicate commands, menu items or software programs
“Quotation marks” indicate names of chapters and terms that are being
emphasized
Êdescribes activities that must be performed in the order
shown
VCAUTION! Pay particular attention to texts marked with this
symbol. Failure to observe this warning may endanger
your life, destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips
Table 2: Notational conventions

Econel 50 Service Supplement 5
2Procedure
VCAUTION!
The actions described in this manual should only be performed by
service personnel.
ÊBefore doing anything else, please take notice of chapter “Safety” on page 7
and following.
ÊMake sure all necessary manuals (see service CD) are available; you may
find it advantageous to print the PDF files. You will definitely need the
Operating Manual and the Options Guide for the server and the Technical
Manual for the system board.
ÊShut down the server correctly, switch it OFF, pull out the power plug, and
open the server as described in the chapter “Replacement Routines” on
page 13 and following.
ÊReplace the defective component as described in the relevant chapter.
ÊClose the server.
ÊConnect the cables.
ÊConnect the server to the line voltage.
ÊStart the operating system.
ÊIf necessary, configure the server as required.