Fujitsu SPARC Enterprise M3000 User manual

1
Accessing Important Information and Documentation
Before you deploy the SPARC Enterprise M3000 server, check for late breaking information about patches for
firmware and software, and known issues. This information, found in the SPARC Enterprise M3000/M4000/M5000/
M8000/M9000 Servers Product Notes, supersedes the information in other documents. The latest version of SPARC
Enterprise M3000/M4000/M5000/M8000/M9000 Servers Product Notes, SPARC Enterprise M3000 Server Installation Guide,
and other documentation for the M3000 server are available on the following website:
http://www.fujitsu.com/sparcenterprise/manual/
SPARC Enterprise M3000 Server Documentation
System
Planning and
Site Preparation
• SPARC Enterprise M3000 Server Overview Guide
• SPARC Enterprise M3000 Server Site Planning Guide
• SPARC Enterprise Equipment Rack Mounting Guide
System
Installation
• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Product Notes
• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Important Legal and Safety
Information (Printed)
• SPARC Enterprise M3000 Server Safety and Compliance Guide
• SPARC Enterprise M3000 Server Getting Started Guide (This document)
• SPARC Enterprise M3000 Server Installation Guide
• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Administration Guide
• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers XSCF User’s Guide
SPARC Enterprise M3000 Server
Getting Started Guide

2
Note – AC power supply model and DC power supply model are available for the M3000 server. The
chapters of each document are written based on AC power supply model. If there is any specific
information on DC power supply model, it is indicated in the appendix “DC Power Supply Model“ of
each document. Be sure to see the appendix when you use DC power supply model.
Installation Steps for SPARC Enterprise M3000 Server
For quick installation and configuration, follow these steps. For more detailed information, see the SPARC
Enterprise M3000 Server Installation Guide.
1. Verify power, air conditioning, and floor area requirements.
Prepare adequate power equipment according to the type of power supply to your server model. For
details, see the SPARC Enterprise M3000 Server Site Planning Guide.
2. Prepare items required for installing the server.
3. Check the delivered items against the “LIST OF ATTACHMENT” that came with the server.
4. Set up the equipment rack and mount the M3000 server.
See the SPARC Enterprise Equipment Rack Mounting Guide.
Caution – Make sure that the power source circuit breaker is in the OFF position before connecting
the power cords.
5. Connect the power cords to the power supply units on the rear panel of the server.
Make sure that each power cord is connected to the server and secured with a cord clamp.
6. Connect the power cords to the power supply system.
The requirements for connecting power cords vary depending on the type of power supply to your server
model. For details, see the SPARC Enterprise M3000 Server Installation Guide.
■AC power supply model
The AC power supply model of the M3000 server is shipped with two grounding-type (three-wire)
power cords. Always connect the power cords into grounded power outlets.
■DC power supply model
The DC power supply model of the M3000 server is shipped with two DC power cords. Since these DC
power cords have a connector only for the server end, a terminal matching the DC power supply
equipment will need to be attached to the DC power supply end of the cord. Moreover, the power
supply equipment must be correctly grounded.
Administration • SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Product Notes
• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Administration Guide
• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers XSCF User’s Guide
• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers XSCF Reference Manual
Repair and
Troubleshooting
• SPARC Enterprise M3000 Server Service Manual
• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Administration Guide
Globalization For SPARC Enterprise M3000 server, the documents of localized versions will be offered on the
website:
http://www.fujitsu.com/sparcenterprise/manual/

3
FIGURE 1 Rear Panel of the Server
7. Use the RS232C cable (serial cable, RJ-45 to DB-9) supplied with the server in the Accessory Kit, and
connect the administration console to the serial port (see FIGURE 1, #3) on the rear panel of the server.
You can use any of the following devices with a DB-9 serial port as the administration console: ASCII
terminal, workstation, terminal server (or a patch panel connected to a terminal server), personal
computer.
Caution – Be careful not to connect a LAN cable to the serial port.
Location Number Component
1 Power supply unit
2PCIeslot
3 Serial port (for XSCF)
4 LAN port (for XSCF)
5 Gigabit Ethernet (GbE) port (for OS)
1 2 34
5
AC Power Supply Model
1234
5
DC Power Supply Model

4
8. The following steps will log in to the XSCF Shell and initialize the XSCF settings.
XSCF is a system control facility to set up and control the server. To initialize the XSCF settings, use the
XSCF default user account.
a. Set the mode switch on the operator panel to the Service mode ( ).
The key for the mode switch is supplied with the server.
FIGURE 2 Operator Panel
b. Turn the power source circuit breaker to "ON".
After the power is turned on, the server starts the XSCF initialization that can take up to 5 or more
minutes. When the initialization completes, the XSCF STANDBY LED ( ) on the operator panel
lights.
c. After the XSCF initialization completes, enter default at the login prompt.
d. Operate the mode switch within one minute according to the messages to change the mode switch.
A login authentication timeout will occur after one minute.
Location Number Name
1 POWER LED
2 XSCF STANDBY LED
3 CHECK LED
4 Power button
5 Mode switch (Key switch)
login: default
Change the panel mode switch to Locked and press return...
Leave it in that position for at least 5 seconds.
Change the panel mode switch to Service, and press return...
1
2
3
4
5

5
e. Confirm that the XSCF Shell prompt is displayed on the administration console.
f. Initialize the XSCF settings. The following are the required settings for installation.
For details on the setting procedure, see the SPARC Enterprise M3000/M4000/M5000/M8000/M9000
Servers XSCF User’s Guide.
g. Log in to the XSCF Shell with the user account and password that were set in Step f.
9. The following steps will power on the server.
a. Confirm that the mode switch on the operator panel is set to the Service mode ( ).
b. From the XSCF Shell, enter the following console command:
This switches you from the XSCF Shell to the domain console.
c. Confirm that the XSCF STANDBY LED ( ) on the operator panel is on.
d. Push the Power button ( ) on the operator panel to power on the server.
The server starts and begins a self-diagnosis. Confirm that no error messages are displayed on the
administration console during the boot process.
e. Confirm that the POWER LED ( ) on the operator panel is turned on.
f. Confirm that ok prompt is displayed on the domain console.
The ok prompt is displayed after the self-diagnosis completes.
XSCF>
Settings Command
Registration of an XSCF user account, password, and user privileges
Registration of a user account of a field engineer (FE) (for maintenance)
adduser, password,
setprivileges
Date and time settings setdate, settimezone
Confirmation of the XSCF host public key showssh
SSH/telnet settings setssh, settelnet
Network interface, routing, and DNS-related settings *
* To apply the settings, the XSCF unit must be reset with the applynetwork and rebootxscf commands.
setnetwork,setroute,
setnameserver etc.
Domain-SP Communication Protocol (DSCP) settings †
† To apply the settings, the XSCF unit must be reset with the rebootxscf commands.
setdscp
Altitude administration setting ‡
‡ To apply changes made with the setdualpowerfeed command, power to the server must be completely disconnected and then
reconnected (all power cords must be disconnected and then reconnected). Wait at least 30 seconds before reconnecting the power cords to
the server.
setaltitude
Dual power feed option setting setdualpowerfeed
XSCF> console -d 0
Connect to DomainID 0?[y|n] :y

6
g. Press the Enter key, and then press the "#" and “.“(period) keys.
This switches you from the domain console to the XSCF Shell.
h. From the XSCF Shell, execute the fmdump command or showlogs command, and confirm that no
errors are found.
10. Connect the system control network to a LAN port (see FIGURE 1, #4) on the rear panel of the server with
an Ethernet cable.
The system control network is a network that connects the XSCF to the administration console for the
system administrator's use. This connection will replace the temporary connection between the
administration console and the serial port.
The LAN ports conform to IEEE 802.3i and IEEE 802.3u. However, only the auto-negotiation mode can be
used for negotiation. The fixed mode cannot be used.
11. Verify the hardware configuration by using the following commands on the administration console
connected to the system control network.
To switch from the XSCF console to the ok prompt, enter the console -d 0 command. To switch from
the ok prompt to the XSCF console, press the enter key, and then press the "#" and "." (period) keys.
12. Install additional hardware or peripheral devices. If not needed, proceed to the Step 13.
For details on how to add optional devices, such as additional memory or an additional PCIe card, see the
SPARC Enterprise M3000 Server Service Manual. To add an additional storage device or other peripheral
device, see the manual supplied with the device.
13. The following steps will connect the domain to the user network. If you isolate the domain from the
network, proceed to the Step 14.
The user network is a network which enables users to access the domain.
a. Connect one end of an Ethernet cable to a GbE port (for the OS) (see FIGURE 1, #5) on the rear panel
of the server.
You can connect the Ethernet cable to a GbE port (for the OS) or to the LAN port on a LAN card
mounted in a PCIe slot (see FIGURE 1, #2).
b. Connect the other end of the Ethernet cable to the customer’s network environment.
Command Prompt Description
showhardconf XSCF Shell All the components installed in the server and their statuses are displayed.
Confirm that no asterisk (*) is displayed in front of any FRUs.
showhardconf -u XSCF Shell Check the number of FRUs mounted on the server against the “PRODUCT
TEST RECORD“ that came with the server.
probe-scsi-all ok Prompt Confirm that the CD-RW/DVD-RW drive unit and hard disk drive
installed in the server are recognized.
show-devs ok Prompt Confirm that each installed PCIe card is recognized.

7
14. The following steps will boot the Oracle Solaris Operating System.
The Oracle Solaris OS is preinstalled in the slot 0 of the hard disk drives.
a. From the ok prompt of the domain console, execute the boot command.
b. After the login prompt is displayed, log in with root account.
15. Confirm hardware operations and device connection statuses by using the Oracle VTS software.
The Oracle VTS software is included in the Oracle Solaris OS. For details, see the Oracle VTS User’s Guide.
16. Make the initial settings for the domain.
For details, see the SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Administration Guide.
ok boot

Manual Code: C120-E536-04EN
March 2012, Revision A
8
FUJITSU LIMITED
Documentation Feedback
If you have any comments or requests regarding this document, or if you find any unclear statements in the
document, please state your points specifically on the form at the following website:
http://www.fujitsu.com/global/contact/computing/sparce_index.html
Copyright ® 2007, 2012, Fujitsu Limited. All rights reserved. Oracle and/or its affiliates provided technical input and review on portions of this material.
Copyright ® 2007, 2012, Fujitsu Limited. Tous droits réservés. Entrée et revue tecnical fournies par Oracle et/ou ses affiliés sur des parties de ce matériel.