Fujitsu PRIMERGY RX300 S7 User manual

PRIMERGY RX300 S7
System configurator and order-information guide
Contents
Instructions
Configuration diagram
Configurator
0 System software
I Basic unit
II Processor
III Memory
IV Graphics
V Accessible drives
VI Hard disk drives
VII PCI Controller
VIII Communication/Network
IX System Management Products (RemoteView)
X Miscellaneous
XI Country specific power cord
Change report
PRIMERGY Server
January 2014

System configurator and order-information guide
PRIMERGY RX300 S7 Status 2013-12-30
Instructions
This document contains basic product and configuration information that will enable you to configure your system via
PC-/System-Architect.
Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete
PRIMERGY Rack system.
You can configure your individual PRIMERGY server in order to adjust your specific requirements.
The System configurator is divided into several chapters that are identical to the current price list and PC-/SystemArchitect.
Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through
the configurator by following the lines from the top to the bottom.
Section
III Memory, example
There are X memory slots which can be equipped with XXX MB.
It is permissible to make up to X passes through the memory upgrade options
S26361-XXX-XXX S26361-XXX-XXX
Memory XXX MB
Memory XXX MB
X times
max. X times per system max. X times per system
In one chapter you can only select as many components (here 4x) as the arrow indicates. 4x
Please note that there are information symbols which indicate necessary information.
For further information see:
http://ts.fujitsu.com/products/standard_servers/index.html
(internet)
https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/current/Pages/default.aspx
(extranet)
Fujitsu PRIMERGY Server 2 of 31

System configurator and order-information guide
PRIMERGY RX300 S7 Status 2013-12-30
Configuration diagram PRIMERGY RX300 S7
System unit ( I )
with up to 6x 3.5" Hard disk drives
Motherboard
front side
Memory CPU1
( Channel A + B + C )
Bay for LocalView LCD
Bank 1 (4 Modules)
Xeon DP
LSD
Bank 2 (4 Modules) 2 USB
Bank 3 (4 Modules) Air channel VGA, LAN
Memory CPU2
Frontpanel
( Channel D + E + F)
Bay for 5,25"x 0,5" SATA-BR
Bank 1 (4 Modules)
Xeon DP
or DVD-ROM/RW
Bank 2 (4 Modules)
Bank 3 (4 Modules)
Memory (III ) Processor ( II )
Accessible drives ( V )
rear side
Fan 1 - Fan 5
1. PSU 2. PSU Needs space for 2
Redundant Fans hard disk drives!
are standard!
Redundant power
3.5"x1,6"
supply option
Backup drive option
Modular RAID
Raid Card for IME, Raid 0 / 1E
Support Raid Card for Raid 5
Low-profile extension slots for:
SCSI Controller for backup( VII )
Hard disk drives ( VI )
SAS Disk Array ( VIII ) 3.5" SAS/SATA
Communication/Network ( IX )
Miscellaneous ( X )
3.5"x1" SAS or SATA
Slot 6 PCIe-3 x16, 390mm @ CPU2
3.5"x1" SAS or SATA
Slot 5 PCIe-3 x16, 390mm @ CPU2
Slot 4 PCIe-3 x8, max. 390mm @ CPU1
3.5"x1" SAS or SATA
Possibility to install PCIe x16 cards
Slot 3 PCIe-3 x8, max. 390mm @ CPU1
3.5"x1" SAS or SATA
Slot 2 PCIe-3 x8, max. 312mm @ CPU1
3.5"x1" SAS or SATA
Slot 1 PCIe-3 x8, max. 168mm @ CPU1 white colored
Dedicated for modular on-board LAN-Controller
Slot 7 PCIe-3 x8, max. 168mm @ CPU1
3.5"x1" SAS or SATA
Internal slot for modular RAID-Controller
Key:
Included in basic unit Option
One CPU, one memory per CPU and one PSU has to be selected for an orderable basic unit.
Fujitsu PRIMERGY Server 3 of 31

System configurator and order-information guide
PRIMERGY RX300 S7 Status 2013-12-30
Configuration diagram PRIMERGY RX300 S7
System unit ( I )
with up to 4, 8, 12 or 16x 2.5" Hard disk drives
Motherboard
front side
Memory CPU1
( Channel A + B + C )
Bay for LocalView LCD
Bank 1 (4 Modules)
Xeon DP
LSD
Bank 2 (4 Modules) 2 USB
Bank 3 (4 Modules) Air channel VGA, LAN
Memory CPU2
Frontpanel
( Channel D + E + F)
Bay for 5,25"x 0,5" SATA-BR
Bank 1 (4 Modules)
Xeon DP
or DVD-ROM/RW
Bank 2 (4 Modules)
Bank 3 (4 Modules)
Accessible drives ( V )
Memory (III ) Processor ( II )
rear side Needs space for 4
Fan 1 - Fan 5 2.5" hard disk drives!
1. PSU 2. PSU 3.5"x1,6"
Redundant Fans
are standard!
Backup drive option 1
Redundant power
supply option
Needs space for 8
2.5" hard disk drives!
5.25"x1,6"
Modular RAID
Raid Card for IME, Raid 0 / 1E
Support Raid Card for Raid 5 Backup drive option 2
Low-profile extension slots for:
SCSI Controller for backup( VII )
Hard disk drives ( VI )
SAS Disk Array ( VIII ) 2.5" SAS/SATA
Communication/Network ( IX )
Miscellaneous ( X ) Up to 4 blocks with 4 HDDs
Slot 6 PCIe-3 x16, 390mm @ CPU2
Slot 5 PCIe-3 x16, 390mm @ CPU2
Slot 4 PCIe-3 x8, max. 390mm @ CPU1
Possibility to install PCIe x16 cards
Slot 3 PCIe-3 x8, max. 390mm @ CPU1
Slot 2 PCIe-3 x8, max. 312mm @ CPU1
Slot 1 PCIe-3 x8, max. 168mm @ CPU1 white colored
Dedicated for modular on-board LAN-Controller
Slot 7 PCIe-3 x8, max. 168mm @ CPU1
Internal slot for modular RAID-Controller
Key:
Included in basic unit Option
One CPU, one memory per CPU and one PSU has to be selected for an orderable basic unit.
2.5" SAS or SATA
2.5" SAS or SATA
2.5" SAS or SATA
2.5" SAS or SATA
2.5" SAS or SATA
2.5" SAS or SATA
2.5" SAS or SATA
2.5" SAS or SATA
Fujitsu PRIMERGY Server 4 of 31

PRIMERGY-Software Configurators and Release Lists
Start PRIMERGY RX300 S7
PRIMERGY RX300 S7 Status 2013-12-30
SW Configurator 32 bit
with OEM-Software without OEM-Software
for PRIMERGY Server for PRIMERGY Server
OEM- SW is bound to HW and
VMware-Software is not allowed to be ordered
- VirtualCenter Management Server for any server released for Windows Server 2003 separately.
- Virtual Infrastructure 3 for PRIMERGY > except all mono PRIMERGY systems Exception: VMware SW
- ESX2 for PRIMERGY RX/TX300S2, RX/TX600S3, BX620S2, BX630 Dual/Quad, BX630 8-way
For all SW products please refer to the corresponding software configurator accessible via
the Extranet under Configuration & Tools, -All configurations, -Software, URL see below.
Linux - Software **)
- Open Enterprise Server ***)
- SuSE Linux ES (OEM): LO
- Red Hat EL (OEM): LO
Microsoft - Windows Server 2008 Server Licenses
- Windows Server 2008 Enterprise
- Windows Server 2008 Standard PRIMECLUSTER *)
- Windows Server 2008 Foundation - Clustering
-
Windows Web Server 2008
- Load Balancing
Microsoft - Windows Server 2008 Client Access Licenses SCO - Software: **)
-
Windows Server 2008 Device CAL
- SCO OpenServer
-
Windows Server 2008 User CAL
(only 1- and 2-way Tower servers)
- Windows Server 2008 Remote Desktop Services Device CAL
- SCO UnixWare (only 1-, 2, and
- Windows Server 2008 Remote Desktop Services User CAL
4-way Tower and Rack servers)
x10sure *)
x10sure Control Nodes and Compute Nodes
Windows Server 2003 Compute Nodes
for PRIMERGY BX600, RX/TX
MultiPath, Duplex Data Manager (DDM)
W2K; W2K3 Linux (W-DDM)
for PRIMERGY except all mono PY systems Details eg. version numbers are published
on the page referred to
Manageability Software: V**) *) Pay attention to the x10sure release and ordering information in the Extranet under
- iRMC advanced Pack https://ts.fujitsu.com/x10sure
- RemoteView Software
- RemoteView Service Board
- RemoteView Diagnosis *) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under
- RemoteDeploy https://partners.ts.fujitsu.com/com/products/software/cluster%20technology/primecluster/Pages/default.aspx
**) Pay attention to release and order information in PRINCE -> Operating System
https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
Backup-Software /
Application-Software: U
- ARCserve
***) Supply over distribution or procurement from FSC VP BC Software
- openSM2
You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:
for internal users:
http://sp.ts.fujitsu.com/dmsp/docs/osrel.xlsx
for partners:
https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
Continue with PRIMERGY
HW configurator
Fujitsu PRIMERGY Server 5 of 31

PRIMERGY-Software Configurators and Release Lists
Start PRIMERGY RX300 S7
PRIMERGY RX300 S7 Status 2013-12-30
SW Configurator 64 bit (EM64T / IA64)
with OEM-Software
without OEM-Software
for PRIMERGY Server for PRIMERGY Server
OEM- SW is bound to HW and
For all SW products please refer to the corresponding is not allowed to be ordered
software configurator accessible via the Extranet under
separately.
"Configuration & Tools, -All configurations, -Software, Exceptions: VMware SW,
URL see below. Citrix XenServer
VMware-Software
- VirtualCenter Management Server for any server released for Windows Server 2003
- Virtual Infrastructure 3 for PRIMERGY > except all mono PRIMERGY systems
- ESX2 for PRIMERGY RX/TX300S2, RX/TX600S3, BX620S2, BX630 Dual/Quad, BX630 8-way
Citrix XenServer / Essentials for XenServer
- XenCenter Management Server for any server released for Windows 2000/XP/Vista and Server 2003/2008
- XenServer and Essentials for XenServer released for RX200S5, RX300S4/S5, RX600S4, BX620S4/S5, BX920S1
Microsoft Hyper-V Server and System Center
- Microsoft System Center Virtual Machine Manager Workgroup Edition for any server released for Windows Server 2008 R2
- Microsoft System Center Essentials Management Suite for any server released for Windows Server 2008 SP2
- Microsoft Hyper-V Server 2008 R2
Microsoft - Windows Server 2008 R2 Server Licenses
Linux - Software *) **)
- Windows HPC Server 2008 R2 Suite # Open Enterprise Server ***)
- Windows Server 2008 R2 Datacenter only
- SuSE Linux ES (OEM): LO
- Windows Server 2008 R2 Enterprise EM64T - Red Hat EL (OEM): LO
- Windows Server 2008 R2 Standard
- Windows Web Server 2008 R2
Microsoft - Windows Server 2008 Server Licenses
- Windows Server 2008 Datacenter PRIMECLUSTER *)
- Windows Server 2008 Enterprise - Clustering
- Windows Server 2008 Standard - Load Balancing
-
Windows Web Server 2008
Microsoft - Windows Server 2008 Client Access Licenses
QuickTransit (QT)
- Windows Server 2008 Device CAL only
Transition Solaris Apps.
-
Windows Server 2008 User CAL
EM64T to x86-64 PY with Linux
-
Windows Server 2008 Remote Desktop Services Device CAL
-
Windows Server 2008 Remote Desktop Services User CAL
only
MultiPath, Duplex Data
EM64T Manager (DDM)
Windows, Linux (W-DDM)
Details eg. version numbers are published
on the page referred to
*) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under
Manageability Software: V**)
https://partners.ts.fujitsu.com/com/products/software/cluster%20technology/primecluster/Pages/default.aspx
- iRMC advanced Pack
only
- RemoteView Software
EM64T - RemoteView Service Board **) Pay attention to release and order information in PRINCE -> Operating System
- RemoteView Diagnosis https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
- RemoteDeploy
***) Supply over distribution or procurement from FSC VP BC Software
You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:
for internal users:
http://sp.ts.fujitsu.com/dmsp/docs/osrel.xlsx
for partners:
https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
Continue with PRIMERGY
HW configurator
Fujitsu PRIMERGY Server 6 of 31

System configurator and order-information guide
Start PRIMERGY RX300 S7
PRIMERGY RX300 S7 Status 2013-12-30
Section IBasic unit
System unit consisting of:
* 2U Housing without power supply modules
* Basic units with:
- 2 Hot-Plug Power Supply Bays
- 5 Fans (full redundancy)
* SAS Backplane for 6x 3.5" HD or SAS Backplanes for 4, 8, 12 or 16x 2.5" HD
with cable connection to on-board or modular RAID Controller
* Drives/Bays
- 6 bays 1" for hot plug 3.5" HD (1" high) or 4, 8, 12 or 16 bays for hot plug 2.5" HD
- 1 bay for 3.5" and 1.6" high Backup device, consumes 2 bays for 3.5" HD for basic unit 6x 3.5" HD
not possible for basic unit with 12 or 16 x 2,5" HD
- 1 bay for 5.25" and 1.6" high Backup device, not possible for basic unit 6x 3.5" HD
for basic unit with 12 or 16 x 2,5" HD
- 1 bay SATA-CD- or DVD-ROM 0,5" height (option)
- 1 bay for opt. LocalView LC-Display
* Integrated ServerView Diagnostics Technology ( Diagnosis LED`s ) for indication of internal
failed components
Systemboard D2939 with:
* Up to two Xeon 4C, 6C & 8C CPU`s (Socket-R)
with 2 serial QPI links ( Quick Path Interconnect ) and four memory channels per CPU
First CPU has to be selected for an orderable basic unit,
* Chipset Intel® C600 Series (codenamed Patsburg)
* 7 PCI slots:
- 2x PCIe-3 x16 (both slots are connected to CPU 2 and are useable with configured 2nd CPU only!)
- 4x PCIe-3 x8 (one notched to install x16 cards)
- 1x PCIe-3 x8 (for internal modular RAID controller only)
* 24 memory slots for max. 768GB RAM DDR3 available
- Memory is divided into 12 DIMMs per CPU ( 4 channels with 3 slots per channel )
Possible max. configurations are:
24x 32GB LRDIMM (quad rank modules) = 768GB
24x 16GB RDIMM (dual rank modules) = 384GB
16x 8GB UDIMM (dual rank modules) = 128GB
First Memory ( one module ) has to be selected for an orderable basic unit per CPU
- Memory upgrade is possible module wise
- Memory mirrroring is supported with 2 identical modules in channel A+B CPU 1 or D+E CPU 2
- Hot Spare Memory is supported with 3 identical modules in channel A+B+C CPU 1 or D+E+F CPU 2
- SDDC (Chipkill) is supported for memory modules,
* Dual Port 10/100/1000 x4 PCI Express* Gigabit Ethernet Intel LAN controller Powerville on-board
* iRMC S3 (integrated Remote Management Controller) on-board server management controller with
dedicated 10/100/1000 Service LAN-port and integrated graphics controller.
The Service LAN-port can be switched alternatively on standard Gbit LAN port 1
* Graphics Controller integrated in iRMC S3 (integrated Remote Management Controller):
1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz,
640x480x32bpp 85Hz
(1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off)
Interfaces at the rear:
* 1x RS-232-C (serial, 9 pins) (usable for BMC or OS or shared)
* 1x VGA (15 pins)
* 4x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup
* 2x LAN RJ45, 1x Service-LAN RJ45
Interfaces on the front:
* 2x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup
* 1x VGA (15 pins) as an option
* 1x Service-LAN RJ45 as an option
Interfaces internal:
* 1x released internal USB Interfaces for backup devices,
* 1x USB 2.0 (UHCI) with 480MBit/s for dongle funcionality (uSSD memory), no USB wakeup
* 1x SATA interface for DVD (only usable with 4x 2.5" HDD + DVD Option)
* 4x SATA/SAS interface for 4 SATA/SAS HD`s or SAS Backup device
* 2x USB 2.0 ports for internal USB redirection connected to BMC
Software:
* ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates
* Documentation engl. (multilingual on CD)
A
Fujitsu PRIMERGY Server 7 of 31

System configurator and order-information guide
APRIMERGY RX300 S7 Status 2013-12-30
Cables included in basic unit
Connections Cable PRIMERGY RX300 S7

SAS
1. SATA DVD    SATA
2. SAS cables to HDDs  
3. 1x cable for SAS signaling  
Note: Rack Mounting kit and Power Cord for RX300S7 is not included in the basic unit and
has to be configured separately
Rack version for 19'' racks with
No PSU included in Base Unit
Basic unit with 2.5" HDD bays is modular expand-
Basic unit is without CPU and Memory able with various modules for backup devices
For an orderable basic unit one CPU = first CPU and integration or up to 16x 2.5" HDDs.
one memory = first memory has to be selected Details and pictures see Section Va:
Basic unit with
Possible configuration options for basic units
6x 3.5" HDD bays fixed S26361-K1373-V101
Basic unit with Full redundancy cannot be guaranteed for a max.
2.5" HDD bays expandable S26361-K1373-V401 config. with e.g. two 135W CPUs with 450W PSUs.
Basic unit with In this case SysArch will generate a warning and
8x 2.5" HDD bays fixed S26361-K1373-V201
Power Safeguard will throttle CPUs
Basic unit with in case of a PSU failure.
12x 2.5" HDD bays fixed S26361-K1373-V301 So, power consumption will be limited to 450W.
S26113-F575-E10
S26113-F574-E10
S26113-F609-E10
450W PSU module platinum 800W PSU module platinum 800W PSU module -48V DC gold
1st or 2nd PSU for redundancy
1st or 2nd PSU for redundancy
1st or 2nd PSU for redundancy
94% efficiency (platinum)
94% efficiency (platinum)
92% efficiency (gold)
uses hot plug PSU slot
uses hot plug PSU slot
uses hot plug PSU slot
min. 1 / max. 2x per system min. 1 / max. 2x per system min. 1 / max. 2x per system
S26113-F574-E99 * For later redundancy upgrade the following kit is available:
Power Supply Dummy
One 450W power supply module hot plug
S26113-F575-L10
must be ordered if 1x PSU only no power cable included!!!
occupies one bay for
One 800W power supply module hot plug
S26113-F574-L10
hot plug power supply no power cable included!!!
max. 1x per system One 800W -48V DC PSU hot plug S26113-F609-L10
no power cable included!!!
Please order appropriate power cord additionally:
*For order completeness only Powercord for rack, 4m, grey, IEC320 C13->C14 connector
T26139-Y1968-L10
Not shown in system architect
Power Cord USA / Canada, 1.8m, grey
T26139-Y1742-L10
Version > V9.2
Power Cord -48V DC, 4m, black
T26139-Y4024-L10
S26361-F3552-E1
TPM Module
Trusted Platform Module on Motherboard
Use according to import restrictions S26361-F3552-L1
max. 1x per system TPM Module add-on kit
for later integration (loose delivery)
Trusted Platform Module on Motherboard
Be aware of import restrictions! Use according to import restrictions
Loose delivery for later
max. 1x per system
integration possible for customer.
B
Fujitsu PRIMERGY Server 8 of 31

System configurator and order-information guide
B
PRIMERGY RX300 S7 Status 2013-12-30
PRIMECENTER Rack
S26361-F2735-E145 S26361-F2735-E175 S26361-F2735-E111 Further information for
RMK-F1_DI_CMA_QRL
Rack Mount Kit F1-C S7 LV
No Rackmount-Kit option
rack mounting is available
best choice for PrimeCenter racks best choice for 3rd party racks Only for loose deliveries within the
consisting of consisting of No mounting in racks possible Corporate Partner Portal
vario carrier 714-785mm vario carrier 559-914mm max. 1x per system
telescopic drop-in rails 781mm telescopic drop-in rails 781mm All "L" no's for loose delivery
with quick release lever support with quick release lever support
with full extraction with full extraction S26361-F2735-L10
with CMA adapter with CMA adapter Adapter angle PC/DC-Rack, till 50Kg
1x per system 1x per system Cnecessary for mounting RMKs in
asymmetrical PC racks
S26361-F2735-L145
RMK-F1_DI_CMA_QRL
S26361-F4530-E11
S26361-F4530-E10 best choice for PrimeCenter racks
Mounting 1U or 2U server in Mounting server in
with CMA adapter
asymmetrical racks symmetrical racks
with 1U support bracket no support bracket needed S26361-F2735-L175
RMK-F1_DI_CMA_QRL_LV
best choice for 3rd party racks
S26361-F2735-E71
S26361-F2735-E82
with CMA adapter
Lateral cable management Rack Cable Management Arm CMA 2U
for 2U servers or higher for 2U Server in racks S26361-F2735-L176
- for asymmetrical racks
- for symmetrical racks
RMK-F1_DI_QRL_LV
PRIMECENTER S2 or M1
M1 or 3rd party racks
best choice for 3rd party racks
- 1 bracket PC Rack asym.
Fujitsu racks w/o CMA adapter
1x per system 1x per system S26361-F2735-L7
Lateral cable management (optionally)
can only be mounted
SNP:SY-F1647E301-P in asymmetrical PRIMECENTER
Installation ex works for one
S2 or new M1 racks in 1U above RMK
server or subsystem.
Hereby the rack will be delivered
S26361-F2735-L82
completely pre-mounted and Rack Cable Management Arm CMA 2U
all wired connections are tested.
for 2U Server in racks.
With PCR M1 16U, 24U, 42U:
Systems and components S26361-F2201-L20
will be delivered installed in the rack Cable arm 2U PCR M1 S and 3rd p.-racks
"Rack-mounting ex factory"
for L176, has to be mounted above RMK
This service is to be ordered once
per installable server/storage
subsystem, in order to get the
To be ordered only together with server/storage subsystem
a PRIMECENTER rack mounted into the racks.
PCR S2 e.g. S26361-K826-V10x In case of not-installed server and subsystems
new PCR M1 e.g. S26361-K827-Vxxx
this service has to be ordered,
refer PCR S2 or M1 rack configurator to get the mounting kits and the
max. 1x per System cables installed.
PRIMERGY Classic 19" rack is not supported
C
Fujitsu PRIMERGY Server 9 of 31

System configurator and order-information guide
PRIMERGY RX300 S7 Status 2013-12-30
C
Section
II Processor
There are 2 processor sockets available.
The first socket must always be equipped with the first CPU which can be selected via configurator
It is also possible to upgrade a dual-processor system later on with a second CPU
Both PCIe-3 x16 slots are connected to CPU 2 and are useable with configured 2nd CPU only!
Two processors with different clock frequencies are not possible
A multi-processor operating system is required for a dual-processor system.
Max. two CPU`s can be selected per basic unit
Note: Max. DDR3 Bus Speed depends on:
One of following CPU´s has to be selected as first CPU - max. DDR3 Bus Speed from the CPU and
for an orderable basic unit - max. DDR3 Memory Speed and
Optional second CPU has to be the same type like the first CPU - max. memory modules on one memory channel
Basic 4C CPU's
- 1x 64-bit Intel Xeon (10MB Smart Cache)
1066 MHz DDR3 Bus; 6,40 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2603 4C/4T 1.80GHz 10MB 6.40GT/s 1066MHz 80W S26361-F3685-E180
Xeon E5-2609 4C/4T 2.40GHz 10MB 6.40GT/s 1066MHz 80W S26361-F3685-E240
Standard Turbo 6C CPU's
- 1x 64-bit Intel Xeon (15MB Smart Cache); Hyper-Threading (HT);
1333 MHz DDR3 Bus; 7,20 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2620 6C/12T 2.00GHz 15MB 7.20GT/s 1333MHz 95W S26361-F3676-E200
Xeon E5-2630 6C/12T 2.30GHz 15MB 7.20GT/s 1333MHz 95W S26361-F3676-E230
Xeon E5-2640 6C/12T 2.50GHz 15MB 7.20GT/s 1333MHz 95W S26361-F3676-E250
Advanced Turbo+ 8C CPU`s
- 1x 64-bit Intel Xeon (20MB Smart Cache); Hyper-Threading (HT);
1600 MHz DDR3 Bus; 8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2650 8C/16T 2.00GHz 20MB 8.00GT/s 1600MHz 95W S26361-F3686-E200
Xeon E5-2660 8C/16T 2.20GHz 20MB 8.00GT/s 1600MHz 95W S26361-F3686-E220
Xeon E5-2665 8C/16T 2.40GHz 20MB 8.00GT/s 1600MHz 115W S26361-F3686-E240
On special release only
Xeon E5-2670 8C/16T 2.60GHz 20MB 8.00GT/s 1600MHz 115W S26361-F3686-E260
Xeon E5-2680 8C/16T 2.70GHz 20MB 8.00GT/s 1600MHz 130W S26361-F3686-E270
Xeon E5-2690 8C/16T 2.90GHz 20MB 8.00GT/s 1600MHz 135W S26361-F3686-E290
Frequency Optimized Turbo 2C, 4C & 6C CPU`s
- 1x 64-bit Intel Xeon (5/10/15MB Smart Cache); Hyper-Threading (HT);
1600 MHz DDR3 Bus; 6,40/7,20 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2637 2C/4T 3.00GHz 5MB 6.40GT/s 1600MHz 80W
S26361-F3687-E300
Xeon E5-2643 4C/8T 3.3GHz 10MB 6.40GT/s 1600MHz 130W S26361-F3687-E330
Xeon E5-2667 6C/12T 2.90GHz 15MB 7.20GT/s 1600MHz 130W S26361-F3687-E290
Low Power 4C/6C/8C CPU's
- 1x 64-bit Intel Xeon (15/20MB Smart Cache); Hyper-Threading (HT);
1333/1600 MHz DDR3 Bus; 7,20/8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2630L 6C/12T 2.00GHz 15MB 7.20GT/s 1333MHz 60W S26361-F3688-E200
Xeon E5-2650L 8C/16T 1.80GHz 20MB 8.00GT/s 1600MHz 70W S26361-F3688-E180
D
Fujitsu PRIMERGY Server 10 of 31

System configurator and order-information guide
PRIMERGY RX300 S7 Status 2013-12-30
D
Section IV Graphics
Graphics Controller integrated in iRMC S3 (integrated Remote Management Controller):
1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz, 640x480x32bpp 85Hz
(1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off)
S26361-F2571-E26
Optional Front-VGA
for Onboard Controller only
consists of internal cable and
front VGA connector
max. 1x per system
The hight end optional NVIDIA NVS300 graphic card offers dual head operation and fully 3D video support.
The cables for either two times DVI-I or VGA (cable kit) connections are part of the delievery.
Optional Front-VGA S26361-F2571-E26 cannot be ordered if NVS300 is required.
Remote Video direction via iRMC must be disabled.
This PCIe-x1 card can also be installed in any PCIe-x4, x8 or x16 slot.
max. 1x Only one card per server is allowed.
S26361-F2748-E637
PY VGA LP card 256MB PCI-e x1
NVIDIA NVS300
512 MB PCIe-x1
PY VGA card must be installed in slot 4 (x8 wired x8)
Connectors: 1x LFH 59
cable kit for 2x DVI or 2x VGA
cable kits included
Dual head + professional 2-D + 3-D
supported for Windows OS
native driver support for Linux OS S26361-F2748-L637
low profile bracket
PY VGA LP card 512MB PCI-e x1
max. 1x per system for loose delivery
E
Fujitsu PRIMERGY Server 11 of 31

System configurator and order-information guide
E
PRIMERGY RX300 S7 Status 2013-12-30
Section
III Memory
- There are 12 memory slots per CPU for max.
384GB LRDIMM (12x 32GB 4R)
192GB RDIMM (12x 16GB 2R)
32GB UDIMM (8x 4GB)
=> max. 768GB for two CPU`s ( 384GB per CPU ), using LRDIMM
- The memory area is divided into 4 channels per CPU with 3 slots per channel
- Slot 1 of each channel belongs to memory bank 1, the slot 2 belongs to memory bank 2,
slot 3 belongs to memory bank 3
Registered, LR DIMMs and unbuffered memory modules can be selected
No mix of registered, load reduced and unbuffered modules allowed.
Memory can be operated at 1.5V or 1.35V, even if the modules are of low voltage type.
Memory operating voltage can be set within BIOS (1.5V is default setting for max. speed).
In a 2 DIMMs per channel configuration, following frequencies are supported:
- 1.5V - 1600MHz max (depending on CPU, special memory modules)
- 1.35V - 1333MHz max (depending on CPU)
In a 3 DIMMs per channel configuration, memory will operate at 1.5V only.
SDDC (Chipkill) is supported for registered / load redueced x4 organized memory modules only
1.) In the "Independent Channel Mode" is following configuration possible
Channels can be populated in any order in Independent Channel Mode. All four
channels may be populated inany order and have no matching requirements. All
channels must run at the same interface frequency but individual channels may run at
different DIMM timings (RAS latency, CAS latency, and so forth)
No mix of registered, load reduced and unbuffered modules allowed.
2.) "Rank Sparing Mode" configuration
- Within a memory channel, one rank is a spare of the other ranks.
The Spare Rank is held in reserve and is not available as system memory
For the effective memory capacity, please refer to the spreadsheet below.
The BIOS is set to the rank sparing setting.
Minimum configuration is: 2x 1R, 2x 2R or 1x4R DDR3 module per channel
This mode is not supported by unbuffered memory modules
3.) "Performance Mode" configuration
- In this configuration, the memory module population ex factory is spread across all channels.
The BIOS is set to the max. performance for memory.
Minimum configuration is: 4x identical modules
4.) In the "Mirrored Channel Mode" is following configuration possible
- Each memory bank can optionallybe equipped with 4x registered or load reduced or unbuffered DDR3 modules
In each memory bank channel Aand B / C and D of CPU 1 or channel E and F / G and H of CPU 2 have to be
equipped with identical modules for mirrored channel mode.
In channel B / D is always the mirrored memoryof channel A / B of CPU 1
In channel F / H is always the mirrored memory of channel E / G of CPU 2
Minimum configuration is: 4x identical modules
This mode is not supported by unbuffered memory modules
F
Fujitsu PRIMERGY Server 12 of 31

System configurator and order-information guide
F
PRIMERGY RX300 S7 Status 2013-12-30
S26361-F3694-E10
Independent Mode
Independent Channel Mode allows all channels to be populated in any order. No specific Memory RAS features are defined
Requires min 1 memory Module per CPU
S26361-F3694-E1 Rank Sparing Mode Installation
BIOS Setup factory preinstalled to this mode. One Rank is spare of other ranks on the same channel. Spare Rank is not shown in System Memory.
For effective capacity within a channel, please have a look below.
Supported for RDIMM / LRDIMM only.
1x per CPU Requires min 2x 1R/2R or 1x 4R modules per CPU
S26361-F3694-E2 Performance Mode Installation
BIOS Setup factory preinstalled for max. Performance, LV memory might be set to 1.5V operation. Four identical memory modules
will be equipped in one memory bank to achieve highest memory performance. All four modules are active and full capacity can be used.
Multiple of 4 identical modules to be configured per CPU
S26361-F3694-E3
Mirrored Channel Mode Installation
BIOS Setup factory preinstalled to this mode. Four identical memory modules are always equipped in one memory bank to use the
Mirrored channel Mode. Only two modules contain active data, the remain two modules contain mirrored data
Supported for RDIMM / LRDIMM only.
Multiple of 4 identical modules to be configured per CPU
1R
2R
1R
2R
4R
4R
na na na na na
na na
na na
Minimum one memory module or order code per CPU = first memory
Note 1.)
Unbuffered Memory (UDIMM) no SDDC (chipkill) support
Max. DDR3 memory speed depends on the memory configuration
- one DDR3 unbuffered ECC mem. Module, 1.35V
(No of mem modules per channe) as well as on the CPU type.
Choose up to 8 order codes per CPU The memory channel with the lowest speed defines the speed
2GB (1x2GB) 1Rx8 L DDR3-1600 U ECC S26361-F3694-E513 of all CPU channels in the system, also for the channels of the
4GB (1x4GB) 2Rx8 L DDR3-1600 U ECC S26361-F3694-E514 second CPU if configured.
Registered Memory (RDIMM) no SDDC (chipkill) support For real memory speed (depending on memory type / population),
- one DDR3 registered ECC mem. Module, 1.35V please check the spreadsheet "Memoryspeed" below
No mix with anyother types of memory modules possible
Choose up to 12x for 1R/2R or 8x for 4R per CPU
For performance reasons, we do not recommend
to configure more than 8 DIMMs per CPU
4GB (1x4GB) 2Rx8 L DDR3-1600 R ECC S26361-F3695-E514
Registered Memory (RDIMM) with SDDC (chipkill) support
8/12x per - one DDR3 registered ECC mem. Module, 1.35V Mix of memory modules is onlypossible within the same group
CPU, max. 1333MHz supported with up to 2DPC (8 modules/CPU)
2/3 modules Choose up to 12 order codes per CPU
per channel 4GB (1x4GB) 1Rx4 L DDR3-1333 R ECC S26361-F3696-E514 new due to supply
8GB (1x8GB) 2Rx4 L DDR3-1333 R ECC S26361-F3696-E515 new due to supply
Registered Memory (RDIMM) with SDDC (chipkill) support
- one DDR3 registered ECC mem. Module, 1.35V
1600MHz supported with up to 2DPC (8 modules/CPU)
at 1.5V
Choose up to 12 order codes per CPU
4GB (1x4GB) 1Rx4 L DDR3-1600 R ECC S26361-F3697-E514
8GB (1x8GB) 2Rx4 L DDR3-1600 R ECC S26361-F3697-E515
16GB (1x16GB) 2Rx4 L DDR3-1600 R ECC S26361-F3697-E516
Load Reduced Memory (LRDIMM) with SDDC (chipkill) support
- one DDR3 load reduced ECC mem. Module, 1.35V
Choose up to 12 order codes per CPU
16GB (1x16GB) 4Rx4 L DDR3-1333 LR ECC S26361-F3698-E516
32GB (1x32GB) 4Rx4 L DDR3-1333 LR ECC S26361-F3698-E517
G
Effective Memory capacity / Rank Sparing Mode, 1 Channel populated
UDIMM
RDIMM
LRDIMM
2GB
2GB
4GB
8GB
2R
16GB
16GB
32GB
1DPC
12GB
24GB
2DPC
4GB
12GB
24GB
28GB
56GB
3DPC
8GB
20GB
40GB
40GB
80GB
Fujitsu PRIMERGY Server 13 of 31

System configurator and order-information guide
PRIMERGY RX300 S7 Status 2013-12-30
Memory Configuration PRIMERGY RX300 S7
Each CPU offers 12 Slots for DDR3 Memory Modules organised in 3 Banks and 4 Channels.
If you need more than 12 Slots you have to configure the 2nd CPU.
Depending on the amount of memory configured you can decide between 4 basic modes of operation (see explanation below).
There are 3 different kinds of DDR3 Memory Modules available: UDIMM / RDIMM and LRDIMM
UDIMM / RDIMM / LRDIMM offer different functionality. Mix of UDIMM / RDIMM / LRDIMM is not alloved.
If 1.5V and 1.35V DIMMs are mixed, the DIMMs will run at 1.5V
Mode Configuration Application
SDDC (chipkill) support any no no yes detect multi-bit errors
Independant Channel 1, 2 or 3 Modules per Bank yes yes yes offers max. flexibility, upgradeability, capacity
Mode
use UDIMM modules for lowest cost
Mirrored Channel Mode *) 4 identical Modules / Bank no no yes offers maximum security
Performance Mode 4 identical Modules / Bank yes yes yes offers maximum performance and capacity
Rank Sparing Mode *) min. 2 Ranks / Channel no no yes
balances security and capacity
*) For the delivery ex works the system will be prepared with dedicated BIOS setting.
Capacity Configuration UDIMM RDIMM LRDIMM Notes
Min. Memory per CPU
1 Module / CPU
1x2GB 1x4GB 1x 16GB
with one CPU
Max. Memory per CPU 8/12 Modules / CPU 8x4GB 12x16GB
12x 32GB
with one CPU
Max. Memory per System 16/24 Modules / System 64GB 384GB 768GB if second CPU is configured
Memory-Speed:
Max. DDR3 memory speed depends on the memory configuration on one memory channel and the speed of the CPU
The memory channel with the lowest speed defines the speed of all CPU channels in the system
Voltage setting (BIOS)
DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC
CPU with 1333MHz DDR3 Bus
CPU with 1066MHz DDR3 Bus
1R - Single Rank
2R - Dual Rank
4R - Quad Rank
1DPC = 1 DIMM per Channel
2DPC = 2 DIMM per Channel
3DPC = 3 DIMM per Channel
Configuration hints:
- The memory sockets on the systemboard offer a color coding:
Bank I black sockets
Bank II blue sockets
Bank III
green sockets
- A so called Bank consits of 1 memory module on every Channel available on one CPU (examples see below)
Bank I on CPU 1/2 up to 4 memory modules connected to Channel A - H on the 1st/2nd CPU
Bank II on CPU 1/2 up to 4 memory modules connected to Channel A - E on the 1st/2nd CPU
Bank III on CPU 1/2
up to 4 memory modules connected to Channel A - E on the 1st/2nd CPU
(can not be populated by UDIMM or 4R RDIMM memory modules)
- See below and next page for a detailed descriptions of the memory configuration supported.
-
-
UDIMM
RDIMM
RDIMM
LRDIMM
x8
x8
x4
Mem. Speed provided
by CPU
Real maximum memory-bus speed depending on CPU type, memory configuration (DPC)
and voltage setting (BIOS)
UDIMM 1600MHz
RDIMM 1600MHz
LRDIMM 1333MHz
1.5V [default]
1.35V
1.5V [default]
1.35V
1.5V [default]
1.35V
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
CPU with 1600MHz DDR3 Bus
1333
1333
-
1066
1066
-
1066
1066
1600
1333
1333
1600
1066
1333
1333
1066
1600
-
1333
-
-
-
1333
1333
-
1066
1066
-
1333
1333
1066
1333
1333
-
1333
1333
1066
1066
1066
-
1066
1066
-
1066
1066
-
1066
1066
1066
1066
-
1066
1066
1066
1066
1066
1066
-
on special release
as soon as available
Fujitsu PRIMERGY Server 14 of 31

System configurator and order-information guide
PRIMERGY RX300 S7 Status 2013-12-30
1. Independent Channel Mode
required
required if 2nd CPU is configured
Bank I Data Data Data Data Data Data Data Data optional, same type in Bank per CPU
(black sockets)
Bank II Data Data Data Data Data Data Data Data optional, any type
(blue sockets)
Bank III
Data Data Data Data Data Data Data Data -------- not used
(green sockets)
Independent Channel Mode allows all channels to be populated in any order
Can run with differently rated DIMMs and use the settings of the slowest DIMM installed in the system
2. Mirrored Channel Mode
required
required if 2nd CPU is configured
Bank I Data Mirror Data Mirror Data Mirror Data Mirror optional, same type in Bank per CPU
(black sockets)
Bank II Data Mirror Data Mirror Data Mirror Data Mirror -------- not used
(blue sockets)
Bank III
Data Mirror Data Mirror Data Mirror Data Mirror
(green sockets)
Mirrored Channel Mode requires identical modules on channel A,B, C, D (1st CPU) or channel E, F, G and H (2nd CPU)
50% of the capacity is used for the mirror => the available memory for applications is only half of the installed memory
If this mode is used, a multiple of 4 identical modules has to be ordered.
3. Performance Channel Mode
required
required if 2nd CPU is configured
Bank I Data Data Data Data Data Data Data Data optional, same type in Bank per CPU
(black sockets)
Bank II Data Data Data Data Data Data Data Data optional, any type
(blue sockets)
Bank III
Data Data Data Data Data Data Data Data -------- not used
(green sockets)
Performance Channel Mode requires identical modules on all channels of each Bank per CPU.
If this mode is used, a multiple of 4 identical modules has to be ordered.
Channel D
Channel E
Channel F
Channel G
Channel H
Channel G
Channel H
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
Channel A
Channel B
Channel C
Channel A
Channel B
Channel C
Channel D
Channel E
Channel F
Channel D
Channel E
Channel F
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8 Core)
Channel A
Channel B
Channel C
Channel G
Channel H
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
Fujitsu PRIMERGY Server 15 of 31

System configurator and order-information guide
PRIMERGY RX300 S7 Status 2013-12-30
4. Rank Sparing Mode
required
required if 2nd CPU is configured
Bank I Spare Spare Spare Spare Spare Spare Spare Spare optional, same type in Channel per CPU
(black sockets)
Bank II Data Data Data Data Data Data Data Data optional, any type
(blue sockets)
Bank III
Data Data Data Data Data Data Data Data
-------- not used
(green sockets)
Bank I R1 Spare Spare Spare Spare Spare Spare Spare Spare
required
(black) R2 Data Data Data Data Data Data Data Data
required if 2nd CPU is configured
Bank II R1 Data Data Data Data Data Data Data Data
(blue) R2 Data Data Data Data Data Data Data Data optional, same type in Channel per CPU
Bank III
R1 Data Data Data Data Data Data Data Data optional, any type
(green) R2 Data Data Data Data Data Data Data Data
-------- not used
Bank I R1 Spare Spare Spare Spare Spare Spare Spare Spare
required
(black) R2 Data Data Data Data Data Data Data Data
R3 Data Data Data Data Data Data Data Data required if 2nd CPU is configured
R4 Data Data Data Data Data Data Data Data
optional, same type in Channel per CPU
Bank II R1 Data Data Data Data Data Data Data Data
(blue) R2 Data Data Data Data Data Data Data Data optional, any type
R3 Data Data Data Data Data Data Data Data
R4 Data Data Data Data Data Data Data Data -------- not used
Bank III
R1 Data Data Data Data Data Data Data Data
(green) R2 Data Data Data Data Data Data Data Data
R3 Data Data Data Data Data Data Data Data
R4 Data Data Data Data Data Data Data Data
Rank Sparing Mode requires identical modules (same capacity and technology) within the same channel.
The available memory for applications will vary depending on configuration. Please refer to the spreadsheet above
"Effective Memory capacity with active Rank Sparing Mode". Population rule for Rank sparing mode is to achieve max.
available memory, e.g. 6 DIMMs will be spread across two channels, each with 3DPC
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
2-Rank Memory modules (RDIMM)
1-Rank Memory modules (RDIMM)
Channel A
Channel B
Channel F
Channel G
Channel H
Channel C
Channel D
Channel E
Channel D
Channel E
Channel A
Channel B
Channel C
Channel D
Channel E
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
Channel G
Channel H
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
4-Rank Memory modules (LRDIMM)
Channel A
Channel B
Channel C
Channel F
Channel G
Channel H
Channel F
Fujitsu PRIMERGY Server 16 of 31

System configurator and order-information guide
G
PRIMERGY RX300 S7 Status 2013-12-30
Section
Va Possible configuration options for basic units
Config 1: 6x or 4x 3.5” HDD + 3.5" DDS/RDX drive
Is fixed due to selection of basic unit with:
6x 3,5" HDD bays fixed S26361-K1373-V101
Basic unit S26361-K1373-V401 with expandable
Config 2: 4x 2.5” HDD S26361-F1373-E420
*)
Available Upgrade kits for this configuration option:
Upgrade kit to 8x 2.5" HDD
S26361-F1373-L424
Upgrade kit to 12x 2.5" HDD S26361-F1373-L427
Upgrade kit to 4x 2.5" HDD + LTO S26361-F1373-L423
Basic unit S26361-K1373-V401 with expandable
Config 3: 4x 2.5” HDD + LTO S26361-F1373-E430
Available Upgrade kits for this configuration option:
Upgrade kit to 8x 2.5" HDD
S26361-F1373-L436
Basic unit S26361-K1373-V201 with
Config. 4: 8x 2,5" HDD bays fixed S26361-K1373-V201
Available Upgrade kits for this fixed configuration:
Upgrade kit to 12x 2.5" HDD S26361-F1373-L247
Upgrade kit to 16x 2.5" HDD S26361-F1373-L248
Basic unit S26361-K1373-V401 with expandable
Config 5: 8x 2.5“ HDD + 3.5“ drive S26361-F1373-E450
No Upgrade kit available!
Basic unit S26361-K1373-V401 with expandable
Config 6: 8x 2.5” HDD + LTO S26361-F1373-E460
no ODD and LSD bay available!
No Upgrade kit available!
Basic unit S26361-K1373-V301 with
Config 7: 12x 2,5" HDD bays fixed S26361-K1373-V301
Available Upgrade kits for this fixed configuration:
Upgrade kit to 16x 2.5" HDD S26361-F1373-L378
Basic unit S26361-K1373-V401 with expandable
Config 8: 16x 2.5” HDD S26361-F1373-E480
no ODD and LSD bay available!
No Upgrade kit available!
Includes all necessary bezels, cages, backplanes and cables
*) this is the only one noHDD configuration opportunity without needed RAID controller
H
Fujitsu PRIMERGY Server 17 of 31

System configurator and order-information guide
PRIMERGY RX300 S7 Status 2013-12-30
H
Section
Vb Accessible drives
Setup RX300 S7 by ServerStart is supported with following configurations:
no DVD, no CD:
remote installation only ( PXE service & DHCP server required)
built in CD/DVD or USB CD/DVD disk drive:
UNC Network share reachable or USB Floppy connected
USB Floppy, no CD/DVD:
USB CD/DVD connected
If installation is done locally, make sure you have
external FDD available for driver installation.
S26361-F3269-E2 S26361-F3641-E2
DVD-RW supermulti slim SATA Blu-ray Triple Writer slim SATA
all formats, DUAL/DL, DVD-RAM
6x BD-RW, 8x DVD, 24x CD
1x BD DL and all CD/DVD formats
0.5 x 5.25", black bezel 0.5 x 5.25"
max. 1x per system max. 1x per system
S26361-F3324-E7 S26361-F3857-E7 Only for basic unit
Tape drive DDS Gen5 USB 3.5"
RDX drive USB 3.5" internal
V1xx
36GB, 3MB/s, USB 2.0 80-320GB, 25MB/s, USB 2.0
1.6 x 3.5", black bezel 1.6 x 3.5", black bezel
within a tape cage within a tape cage
incl. description (Ger/US) incl. description (Ger/US)
cleaning cartridge without RDX cartridges
occupies 2 x 1" hard disk bays
occupies 2 x 1" hard disk bays
max. 1x per system max. 1x per system
1x
S26361-F3324-E5 S26361-F3325-E2 S26361-F3857-E5
Tape drive DDS Gen5 USB 3.5" Tape drive DDS Gen6 USB 3.5"
RDX drive USB 3.5" internal
36GB, 3MB/s, USB 2.0 80GB, 6MB/s, USB 2.0 80-320GB, 25MB/s, USB 2.0
Only for basic unit
Connector: USB "B" Connector: USB "B" Connector: USB "B" V4xx
with USB cable with USB cable with USB cable
incl. description (Ger/US) incl. cleaning cartridge incl. description (Ger/US)
cleaning cartridge
without data cartridge
without RDX cartridges
1.6 x 3.5", black bezel 1.6 * 3.5", black bezel 1.6 x 3.5", black bezel
max. 1x per system max. 1x per system max. 1x per system
H1
Fujitsu PRIMERGY Server 18 of 31

System configurator and order-information guide
PRIMERGY RX300 S7 Status 2013-12-30
H1
S26361-F3749-E201 The adapter is also available as optional (loose) delivery
USB3.0 PCIe x1 adapter card lp with FH and LP bracket included
Sunrich U-720 S26361-F3749-L501
PCIe x1
1 port intern, 1 port extern
USB 3.0 A jacks
max. 1x per system
Only for basic unit
Only for basic unit
V4xx
V1xx
as soon as available
S26361-F3750-E5 S26361-F3750-E7
RDX cartridges must be ordered separately
RDX Drive USB3.0 3.5" internal RDX Drive USB3.0 3.5" internal RDX 320GB = S26361-F3857-L320
100MB/s, USB 3.0 100MB/s, USB 3.0 RDX 500GB = S26361-F3857-L500
Connector: USB 3.0 "B"
Connector: USB 3.0 "B"
RDX 1TB = S26361-F3857-L600
with USB cable within tape cage w/ USB cable 10x RDX320 = S26361-F3857-L329
without RDX cartridges without RDX cartridges
1.6 x 3.5", black bezel 1.6 x 3.5", black bezel The drive is also available as optional (loose) delivery
max. 1x per system max. 1x per system S26361-F3750-L5/L7 with USB3.0 cable for adapter card.
The USB3.0 Adapter card or the USB2.0 cable set
S26361-F3750-L20 must be ordered with the drive!
as soon as available additional RDX cartridges can be ordered
S26361-F3750-E325 S26361-F3750-E327 RDX 320GB = S26361-F3857-L320
RDX 320 3.5" RDX 320 3.5" RDX 500GB = S26361-F3857-L500
100MB/s, USB 3.0 100MB/s, USB 3.0 RDX 1TB = S26361-F3857-L600
Connector: USB 3.0 "B"
Connector: USB 3.0 "B"
10x RDX320 = S26361-F3857-L329
with USB3.0 cable with USB3.0 cable
with 320GB RDX cartridge with 320GB RDX cartridge The bundle is also available as optional (loose) delivery
1.6 * 3.5", black bezel 1.6 * 3.5", black bezel
S26361-F3750-L325 with USB3.0 cable for adapter card.
max. 1x per system max. 1x per system The USB3.0 Adapter card or the USB2.0 cable set
S26361-F3750-L20 must be ordered with the drive!
as soon as available additional RDX cartridges can be ordered
S26361-F3750-E505 S26361-F3750-E507 RDX 320GB = S26361-F3857-L320
RDX 500 3.5" RDX 500 3.5" RDX 500GB = S26361-F3857-L500
100MB/s, USB 3.0 100MB/s, USB 3.0 RDX 1TB = S26361-F3857-L600
Connector: USB 3.0 "B"
Connector: USB 3.0 "B"
10x RDX320 = S26361-F3857-L329
with USB3.0 cable with USB3.0 cable
with 500GB RDX cartridge with 500GB RDX cartridge The bundle is also available as optional (loose) delivery
1.6 * 3.5", black bezel 1.6 * 3.5", black bezel
S26361-F3750-L505 with USB3.0 cable for adapter card.
max. 1x per system max. 1x per system The USB3.0 Adapter card or the USB2.0 cable set
S26361-F3750-L20 must be ordered with the drive!
as soon as available additional RDX cartridges can be ordered
S26361-F3750-E605 S26361-F3750-E607 RDX 320GB = S26361-F3857-L320
RDX 1000 3.5"
RDX 1000 3.5"
RDX 500GB = S26361-F3857-L500
100MB/s, USB 3.0 100MB/s, USB 3.0 RDX 1TB = S26361-F3857-L600
Connector: USB 3.0 "B"
Connector: USB 3.0 "B"
10x RDX320 = S26361-F3857-L329
with USB3.0 cable with USB3.0 cable
with 1TB RDX cartridge with 1TB RDX cartridge The bundle is also available as optional (loose) delivery
1.6 * 3.5", black bezel 1.6 * 3.5", black bezel
S26361-F3750-L605 with USB3.0 cable for adapter card.
max. 1x per system max. 1x per system The USB3.0 Adapter card or the USB2.0 cable set
S26361-F3750-L20 must be ordered with the drive!
H2
USB 3.0 adapter & RDX
Fujitsu PRIMERGY Server 19 of 31

System configurator and order-information guide
PRIMERGY RX300 S7 Status 2013-12-30
H2
SAS Controller for internal Backup Drives
S26361-F3674-E1 For internal SAS Backup drives
Onboard 4 port SAS Controller
an additional 4-port SAS controller has to be configured
LSI
Patsburg B
RAID 0, 1 & 10
no controller cache
SAS 1.0 (3Gb/sec)
Only for basic unit
4 internal ports
V4xx
PCIe x4
no PCI slot required
max. 1x per system
as soon as available
S26361-F3561-E4 S26361-F3626-E2 S26361-F3627-E1 S26361-F3787-E1
Tape drive LTO3HH Ultrium SAS Tape drive LTO4 HH SAS IBM V2 Tape drive LTO5HH Ultrium SAS Tape drive LTO6HH Ultrium SAS
400GB, 60MB/s, SAS 3Gb 800GB, 120MB/s, SAS 6Gb 1500GB, 140MB/s, SAS 6Gb 2500GB, 160MB/s, SAS 6Gb
Connector: mini-SAS Connector: mini-SAS Connector: mini-SAS Connector: mini-SAS
1x incl. SAS cable incl. SAS cable incl. SAS cable incl. SAS cable
incl. cleaning cartridge incl. cleaning cartridge incl. cleaning cartridge incl. cleaning cartridge
without data cartridge
without data cartridge
without data cartridge
without data cartridge
1.6 * 5.25", black bezel
1.6 * 5.25"
1.6 * 5.25"
1.6 * 5.25"
max. 1x per system max. 1x per system max. 1x per system max. 1x per system
I
Fujitsu PRIMERGY Server 20 of 31