Fujitsu Primergy RX600 S2 User manual

1
PRIMERGY RX600 S2 User’s Guide
Areas Covered
Before Reading This Manual
This section explains the notes for your safety and conventions used in this manual.
Chapter 1 Overview
This chapter explains component names and basic operations of this server, as well as an
overview of the software provided with this server. In addition, the workflow, from placing the
server to starting the operation, is also described.
Chapter 2 Checking before OS Installation
This chapter explains the preparation on the server and cautions necessary before OS installation.
Please read this chapter before starting installation.
Chapter 3 OS Installation Using ServerStart
This chapter explains how to install the OS in the server using ServerStart.
Chapter 4 Manual OS Installation
This chapter explains how to install the OS without using ServerStart.
Chapter 5 Operations after OS Installation
This chapter explains the operations to perform after OS installation. Be sure to perform those
operations before operating the server.
Chapter 6 High Reliability Tools
For stable PRIMERGY server operations, we recommend that high reliability tools be installed.
This chapter explains the installation and necessary settings of high reliability tools.
Chapter 7 Installing Internal Options
This chapter explains how to install and remove the various internal options.
Chapter 8 Configuring Hardware and Utilities
This chapter explains how to make the environment settings necessary to operate the server and
how to use each utility.
Chapter 9 Operation and Maintenance
This chapter explains the operations necessary after starting to use this server as well as daily
care and maintenance.
Appendix
This appendix explains the specifications for the server and for its internal options.

2
Before Reading This Manual
■Trademarks
EGA/VGA and PS/2 are registered trademarks of IBM Corporation.
Microsoft, Windows, and Windows Server are trademarks or registered trademarks of Microsoft Corporation in the USA
and other countries.
Intel and Pentium are registered trademarks or trademarks of Intel Corporation or its subsidiaries in the USA and other
countries.
Linux is a trademark or registered trademark of Linus Torvalds in the USA and other countries.
Red Hat and all Red Hat-based trademarks and logos are trademarks or registered trademarks of Red Hat, Inc. in the
USA and other countries.
All other hardware and software names used are trademarks or registered trademarks of their respective manufacturers.
Other product names are copyrights of their respective manufacturers.
All Rights Reserved, Copyright© FUJITSU LIMITED 2005
Screen shot(s) reprinted with permission from Microsoft Corporation.
For Your Safety...
This manual contains important information, required to operate the server safely.
Thoroughly review the information in this manual before using the server. Especially note the points under "Safety Precautions", and only
operate the server with a complete understanding of the material provided.
This manual and "Safety Precautions" should be kept in an easy-to-access location for quick reference when using this server.
Data Backup
To protect data stored in this device (including basic software and application software), perform backup and other necessary operations. Note
that data protection is not guaranteed when repairs are performed. It is the customer's responsibility to maintain backup copies in advance.
In case of data loss, Fujitsu assumes no liability for data maintenance or restoration and damages that occur as a result of the data loss for any
reason, except for items covered under warranty.
High Safety
The Products are designed, developed and manufactured as contemplated or general use, including without limitation, general office use,
personal use, household use, and ordinary industrial use, but are not designed, developed and manufactured as contemplated for use
accompanying fatal risks or dangers that, unless extremely high safety is secured, could lead directly to death, personal injury, severe physical
damage, or other loss (hereinafter "High Safety Required Use"), including without limitation, nuclear reaction control in nuclear facility,
aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system. You
shall not use this Product without securing the sufficient safety required for the High Safety Required Use. If you wish to use this Product for
High Safety Required Use, please consult with our sales representatives in charge before such use.
Problems may occur with this device in the event of an instantaneous voltage drop of the power supply due to lightning, etc. To prevent an
instantaneous voltage drop of the power supply, we recommend that you use an uninterruptible power supply system.

3
PRIMERGY RX600 S2 User’s Guide
Remarks
■Warning Descriptions
Various symbols are used throughout this manual. These are used to emphasize important points for your
safety and that of others. The following are the symbols and their meanings.
The following symbols are used to indicate the type of warning or caution being described.
■Symbols
Symbols used in this manual have the following meanings.
■Key Descriptions / Operations
Keys are represented throughout this manual in the following manner.
E.g.: [Ctrl] key, [Enter] key, [→] key, etc.
The following indicate pressing several keys at once:
E.g.: [Ctrl] + [F3] key, [Shift] + [↑] key, etc.
■Entering Commands (Keys)
Command entries are displayed in the following way.
• In the areas of the "↑" mark, press the [Space] key once.
• When using Windows or DOS OS, commands are not case sensitive.
• CD-ROM drive names are shown as [CD-ROM drive]. Enter your drive name according to your
environment.
[CD-ROM drive]:\setup.exe
Ignoring this symbol could be potentially lethal.
Ignoring this symbol may lead to physical injury and/or damage the server or internal options.
The triangle mark emphasizes the urgency of the WARNING and CAUTION. Details are
described after the triangle.
A barred circle ( ) warns against certain actions (Do Not). Details are described after the
circle.
A black circle indicates actions that must be taken. Details are described after the black circle.
These sections explain prohibited actions and points to note when using this device. Make
sure to read these sections.
These sections explain information needed to operate the hardware and software properly.
Make sure to read these sections.
→This mark indicates reference pages or manuals.

4
■Screen Shots and Figures
Screen shots and figures are used as visual aids throughout this manual. Windows, screens, and file
names may vary depending on the OS, software, or configuration of the server used. Figures in this
manual may not show cables that are actually connected for convenience of explanation.
■Consecutive Operations
Consecutive operations are described by connecting them with arrows (→).
■Product Names
The following expressions and abbreviations are used throughout this manual.
Example: Procedure of clicking the [Start] button, pointing to [Programs], and clicking [Accessories]
↓
Click [Start] →[Programs] →[Accessories].
table: Abbreviations of Product Names
Product name Expressions and abbreviations
PRIMERGY RX600 S2 This server or the server
Microsoft®Windows Server™2003, Standard
Edition
Windows Server 2003,
Standard Edition
Windows
Server 2003
Windows
Microsoft®Windows Server™2003, Enterprise
Edition
Windows Server 2003,
Enterprise Edition
Microsoft®Windows Server™2003, Standard x64
Edition
Windows Server 2003 x64
Microsoft®Windows Server™2003, Enterprise x64
Edition
Microsoft®Windows®2000 Server Windows 2000 Server
Microsoft®Windows®2000 Advanced Server Windows 2000 Advanced
Microsoft®Windows®Preinstallation Environment Windows PE
Microsoft®Windows®Server Network Operating
System Version 4.0
and Microsoft®Windows NT®Server, Enterprise
Edition 4.0
Windows NT Server 4.0
Microsoft®Windows® XP Professional Windows XP Professional
Microsoft®Windows® 2000 Professional Windows 2000 Professional
Microsoft®Windows NT®Workstation Operating
System 4.0
Windows NT
Microsoft®Windows Server™2003 Service Pack Service Pack
Microsoft®Windows®2000 Service Pack
Red Hat Enterprise Linux AS (v.3 for x86) Linux
Red Hat Enterprise Linux AS (v.4 for x86)
Red Hat Enterprise Linux AS (v.4 for EM64T)

5
PRIMERGY RX600 S2 User’s Guide
■Server Types
Server types are described as follows.
Reference Information
■Software Manuals
Software Manual contains other reference information and cautions for ServerStart not described in this
manual. Please read it before using ServerStart.
Software Manual is contained as a "README.TXT" file in the root directory on the ServerStart CD-
ROM. Use a text editor to read it.
■Latest Information about Software Provided with This Server
For the latest information regarding ServerStart and other software provided with this server, refer to the
Fujitsu PRIMERGY website (http://primergy.fujitsu.com).
Warning and Caution Labels
Warning and caution labels are found on the server.
Do not remove or stain these labels.
table: Server Types
Type Expressions and
abbreviations
Servers without an internal hard disk Diskless Type

6

7
PRIMERGY RX600 S2 User’s Guide
Contents
Chapter 1 Overview
1.1 RX600 S2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.2 Supplied Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.2.1 Setup Support Tool - ServerStart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
1.2.2 High Reliability Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
1.2.3 Installing High Reliability Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
1.3 Component Names and Functions . . . . . . . . . . . . . . . . . . . . . . . 22
1.3.1 Server (Front View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
1.3.2 Server (Rear View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
1.3.3 Server (Internal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
1.3.4 Baseboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
1.3.5 Memory Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
1.4 Standard Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
1.4.1 Opening the Rack Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
1.4.2 Turning On the Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
1.4.3 Turning Off the Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
1.4.4 Inserting and Ejecting a CD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
1.4.5 How to Use the LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
1.5 Workflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Chapter 2 Checking befor OS Installation
2.1 Preparation on the Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
2.1.1 Installing Internal and External Options . . . . . . . . . . . . . . . . . . . . . . . . . . .44
2.1.2 Hardware Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
2.2 Selecting the Installation Method . . . . . . . . . . . . . . . . . . . . . . . . 48
2.3 Precautions on Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
2.3.1 Installation Partition Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
2.3.2 Notes on Configuring RAID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
2.3.3 Notes on a Multiple LAN Adapter Configuration . . . . . . . . . . . . . . . . . . . .50
2.3.4 Cautions for Using ServerStart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
2.3.5 Expansion Cards Supported by ServerStart . . . . . . . . . . . . . . . . . . . . . . .52
2.3.6 Cautions for Manual Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
2.4 Preparation for Using ServerStart on a Client Computer . . . . . 53
2.4.1 Installing ServerStart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
2.4.2 Uninstalling ServerStart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Chapter 3 OS Installation Using ServerStart
3.1 Guided Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
3.1.1 Starting Up the Guided Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
3.1.2 Open/create a Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

8
3.1.3 RAID Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
3.1.4 Disk Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
3.1.5 OS Installation Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
3.1.6 Application Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
3.1.7 Close/save the Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
3.1.8 Start OS Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
3.2 Preconfiguration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
3.2.1 Starting Up the Preconfiguration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
3.2.2 Configure Settings in Wizards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
3.2.3 Close/save the Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
3.2.4 Starting OS Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
3.3 Expert Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
3.3.1 Starting Up the Expert Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
3.3.2 Disk Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
3.3.3 OS Installation Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
3.3.4 Application Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
3.3.5 Start OS Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
3.4 Remote Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
3.4.1 Overview of Remote Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
3.4.2 System Requirements for Remote Resource/PXE Servers . . . . . . . . . . . 90
3.4.3 Preparation of the PXE Server (When the PXE Server is Used) . . . . . . . 91
3.4.4 Preparation of Remote Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
3.4.5 Starting Remote Installation Using a PXE Server . . . . . . . . . . . . . . . . . . . 99
3.4.6 Starting Remote Installation Using a Remote Resource Server . . . . . . . 102
3.5 Installation on Multiple (the Second and Subsequent) Servers . .
106
3.5.1 Preparation for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
3.5.2 Installation in Guided Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
3.5.3 Installation in Preconfiguration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Chapter 4 Manual OS Installation
4.1 Creating Driver Disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
4.1.1 Required Driver Disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
4.1.2 How to Create Driver Disks [FloppyBuilder function] . . . . . . . . . . . . . . . 114
4.2 Starting Manual Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
4.2.1 Installing Windows Server 2003 x64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
4.2.2 Installing Windows Server 2003 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
4.2.3 Installing Windows 2000 Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
4.2.4 Installing Linux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
4.3 Installing the LAN Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
4.3.1 Installing the LAN Driver (Windows Server 2003 x64) . . . . . . . . . . . . . . 126
4.3.2 Installing the LAN Driver (Windows Server 2003) . . . . . . . . . . . . . . . . . . 127
4.3.3 Installing the LAN Driver (Windows 2000 Server) . . . . . . . . . . . . . . . . . . 130
4.3.4 Latest Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

9
PRIMERGY RX600 S2 User’s Guide
Chapter 5 Operations after OS Installation
5.1 Memory Dump/Paging File Setting . . . . . . . . . . . . . . . . . . . . . . 134
5.1.1 How to Obtain Memory Dump For Windows Server 2003 . . . . . . . . . . .134
5.1.2 How to Obtain Memory Dump For Windows 2000 Server . . . . . . . . . . .138
5.2 Creating a Disk for System Recovery . . . . . . . . . . . . . . . . . . . . 143
5.2.1 Creating the Automated System Recovery (ASR) Set For Windows Server
2003 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
5.2.2 Creating a System Recovery Disk For Windows 2000 Server . . . . . . . .144
5.3 Storing the System Configuration Information . . . . . . . . . . . . 145
5.3.1 How to Store the BIOS Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146
5.3.2 How to Recover the BIOS Information . . . . . . . . . . . . . . . . . . . . . . . . . .147
5.4 Creating Maintenance Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
5.4.1 Creating a DOS Floppy Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
5.5 Notes Before Operating the Server . . . . . . . . . . . . . . . . . . . . . 152
5.5.1 Updating the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152
5.5.2 Auto-run Function from CD-ROM Drives . . . . . . . . . . . . . . . . . . . . . . . . .152
5.5.3 Drive Letter Assignment in Expert Mode . . . . . . . . . . . . . . . . . . . . . . . . .152
5.5.4 Notes on Advanced Uninterruptible Power Supply (UPS) . . . . . . . . . . . .153
5.5.5 Turning the Power On via a LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
5.5.6 Other Notes on Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
5.6 LAN Driver Advanced Setup [BACS] . . . . . . . . . . . . . . . . . . . . 157
5.6.1 BACS Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
5.6.2 Load Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
5.6.3 VLAN Setup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162
5.6.4 Cautions on Using the Teaming (SLB (Auto-Fallback Disable)) Function
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163
5.7 LAN Driver Advanced Setup [Intel® PROSet] . . . . . . . . . . . . . 165
5.7.1 Intel® PROSet Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165
5.7.2 Notes on Referring to the Intel® PROSet Help Topics . . . . . . . . . . . . . .166
5.7.3 Cautions for PG-1852/1862/188x/189xLAN Driver V9.2 . . . . . . . . . . . . .167
5.7.4 Teaming Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167
5.7.5 VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168
5.7.6 Local Address Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169
5.7.7 Jumbo Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170
Chapter 6 High Reliabillity Tools
6.1 RAID Management Tool [Global Array Manager] . . . . . . . . . . 172
6.1.1 Installing RAID Management Tool (Global Array Manager) . . . . . . . . . .172
6.2 Server Monitoring Tool [ServerView] . . . . . . . . . . . . . . . . . . . . 173
6.2.1 Installing ServerView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174
6.2.2 Setting Required after Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174
6.3 Solving Problems Early [DSNAP] . . . . . . . . . . . . . . . . . . . . . . . 176
6.3.1 Installing DSNAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .176
6.3.2 How to Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .176

10
Chapter 7 Installing Internal Options
7.1 Before Installing Internal Options . . . . . . . . . . . . . . . . . . . . . . 178
7.2 Removing and Attaching the Top Cover . . . . . . . . . . . . . . . . . . 180
7.2.1 Removing the Top Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
7.3 Installing CPUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
7.3.1 Where to Install CPUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
7.3.2 Installable CPUs and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
7.3.3 How to Install CPUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
7.3.4 Defective CPU Disconnection Function . . . . . . . . . . . . . . . . . . . . . . . . . 188
7.4 Installing Memory Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
7.4.1 Where to Install the Memory Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
7.4.2 Installable Memory Modules and Notes . . . . . . . . . . . . . . . . . . . . . . . . . 191
7.4.3 Memory Redundant Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
7.4.4 How to Install Memory Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
7.4.5 Defective Memory Disconnection Function . . . . . . . . . . . . . . . . . . . . . . . 200
7.4.6 How to Replace Memory Modules under Hot-plug Support . . . . . . . . . . 200
7.5 Installing Expansion Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
7.5.1 Where to Install an Expansion Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
7.5.2 Installable Expansion Cards and Notes on Installation . . . . . . . . . . . . . . 206
7.5.3 How to Install Expansion Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
7.5.4 How to Replace Expansion Cards in the Hot-Swappable PCI Slots . . . 212
7.6 Installing Internal Hard Disk Units . . . . . . . . . . . . . . . . . . . . . . 214
7.6.1 Where to Install Internal Hard Disk Units . . . . . . . . . . . . . . . . . . . . . . . . 214
7.6.2 Installable Internal Hard Disk Units and Notes . . . . . . . . . . . . . . . . . . . . 215
7.6.3 How to Install Internal Hard Disk Units . . . . . . . . . . . . . . . . . . . . . . . . . . 216
7.6.4 How to Remove Internal Hard Disk Units . . . . . . . . . . . . . . . . . . . . . . . . 217
7.6.5 Replacing the Failed Internal Hard Disk Unit . . . . . . . . . . . . . . . . . . . . . 218
7.7 Installing 5-inch Internal Device . . . . . . . . . . . . . . . . . . . . . . . . 219
7.7.1 Where to Install 5-inch Internal Devices . . . . . . . . . . . . . . . . . . . . . . . . . 219
7.7.2 Installable 5-inch Internal Devices and Notes . . . . . . . . . . . . . . . . . . . . . 220
7.7.3 How to Install the 5-inch Internal Device . . . . . . . . . . . . . . . . . . . . . . . . . 220
7.8 Connecting External SCSI Devices . . . . . . . . . . . . . . . . . . . . . . 226
7.8.1 Connecting a Hard Disk Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
7.8.2 Connecting External SCSI Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
Chapter 8 Configuring Hardware and Utilities
8.1 Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
8.1.1 Jumper Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
8.1.2 Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
8.2 Configuring Boot Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
8.2.1 System Options Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
8.2.2 Boot Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
8.2.3 Boot Maintenance Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234