Fujitsu PRIMERGY TX100 S1 User manual

PRIMERGY TX100 S1
Options Guide
Edition August 2009

Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
email: [email protected].
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
Copyright © 2009 Fujitsu Technology Solutions GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trade names and/or trademarks of their respective
manufacturers.

TX100 S1 Options Guide
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Concept and target groups . . . . . . . . . . . . . . . . . . . 5
1.2 Documentation overview . . . . . . . . . . . . . . . . . . . . 6
1.3 Expansions and upgrades . . . . . . . . . . . . . . . . . . . . 7
1.4 Notational conventions . . . . . . . . . . . . . . . . . . . . . 8
2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . 11
4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 17
4.2 Removing the air duct . . . . . . . . . . . . . . . . . . . . . 22
5 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.1 Equipping rules . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.2 Extending/replacing the main memory . . . . . . . . . . . . 24
6 Accessible drives . . . . . . . . . . . . . . . . . . . . . . . 27
6.1 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.2 Installing an accessible 5.25-inch drive . . . . . . . . . . . . 29
7 Expansion cards and parallel interface . . . . . . . . . . . . 31
7.1 Installing an expansion card . . . . . . . . . . . . . . . . . . 32
7.2 Installing a parallel interface . . . . . . . . . . . . . . . . . 34

OptionsGuide TX100 S1
Contents
8 Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8.1 Installing the air duct . . . . . . . . . . . . . . . . . . . . . . 37
8.2 Closing the server . . . . . . . . . . . . . . . . . . . . . . . . 38
9 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
9.1 Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

TX100 S1 Options Guide 5
1 Introduction
The PRIMERGY TX100 S1 server is an Intel-based server for workgroups and
small networks. The server is suitable for use as a file server and also as an
application, information or Internet server.
Thanks to its highly developed hardware and software components, the
PRIMERGY TX100 S1 server offers a high level of data security and availability.
Security functions in the BIOS-Setup and on the system board protect the data
on the server against manipulation. The supported RAID levels allow the hard
disk controllers to offer error tolerance, through data redundancy, for users who
want to provide complete protection for valuable data.
Its low noise level and high energy efficiency make it ideal for office
environments.
1.1 Concept and target groups
This Options Guide shows you how to extend and upgrade your server.
VCAUTION!
The activities described in this manual may only be performed by
technical specialists.
IThe installation and removal of the hot-plug components is described in
the Operating Manual supplied with the server.
The PRIMERGY TX100 S1 has a power management function
that reduces power consumption to <65 W in typical
configurations. The server thus satisfies the requirements of the
U.S. Environmental Protection Agency (EPA).

6 OptionsGuide TX100 S1
Documentation overview Introduction
1.2 Documentation overview
More information on your PRIMERGY TX100 S1 can be found in the following
documents:
– "Quick Start Hardware - PRIMERGY TX100 S1" leaflet (only included as a
printed copy)
– "Quick Start Software - Quick Installation Guide" DVD booklet (only included
with the PRIMERGY ServerView Suite as a printed copy)
– "Safety notes and other important information" manual
– "Warranty" manual
– "Returning used devices" manual
– "Helpdesk" leaflet
– Technical manual for the system board D2679-B11
– "PRIMERGY TX100 S1 Server Operating Manual"
– "PRIMERGY TX100 S1 Server Options Guide"
– "D2679-B11 BIOS Setup Utility for PRIMERGY TX100 S1" manual
IPRIMERGY manuals are available in PDF format on the PRIMERGY
ServerView Suite DVD 2. The PRIMERGY ServerView Suite DVD 2 is
part of the PRIMERGY ServerView Suite supplied with every server.
If you no longer have the ServerView Suite DVDs, you can obtain the
relevant current versions using the order number U15000-C289.
The PDF files of the manuals can also be downloaded free of charge
from the Internet. The overview page showing the online documentation
available on the Internet can be found using the URL:
http://manuals.ts.fujitsu.com. The PRIMERGY server documentation can
be accessed using the Industry standard servers navigation option.

TX100 S1 Options Guide 7
Introduction Expansions and upgrades
Further sources of information:
– PRIMERGY Abbreviations and Glossary on the PRIMERGY
ServerView Suite DVD 2
– Manual for the monitor
– Documentation for the boards and drives
– Operating system documentation
– Information files in your operating system
1.3 Expansions and upgrades
Upgrading the main memory
The system board supports up to 8 Gbyte of main memory. There are 4 slots
available for the main memory. The slots can be fitted with 1 Gbyte and 2 Gbyte
PC2-6400 DDR2 800 MHz (unbuffered) DIMM memory modules.
Additional accessible drives
There is one free 5.25-inch bay for an additional accessible drive. The first
(upper) bay already has a DVD drive.
Slots for expansion cards
The server can be flexibly expanded via four slots:
– One PCIe Gen2 x 8 slot
– One PCIe Gen2 x 4 (mech. x8) slot
– One PCIe Gen2 x 1 slot
– One PCI slot
Parallel interface for printers
As an option, a parallel interface can be provided for printers.

8 OptionsGuide TX100 S1
Notational conventions Introduction
Trusted Platform Module (TPM)
IThe system board is optional equipped with a TPM (Trusted Platform
Module) by the manufacturer. This module enables programs from third
party manufacturers to store key information (e.g. drive encryption using
Window's Bitlocker Drive Encryption).
The TPM is activated via the BIOS system (for more information, refer to
the BIOS manual).
1.4 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands or menu items.
"Quotation marks" indicate names of chapters and terms that are being
emphasized.
Êdescribes activities that must be performed in the order
shown.
VCAUTION! pay particular attention to texts marked with this symbol.
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips.

TX100 S1 Options Guide 9
2Procedure
VCAUTION!
●The actions described in this manual should only be carried out by
technical specialists.
●Equipment repairs should only be performed by service staff. Please
note that unauthorized interference with the system will void the
warranty and exempt the manufacturer from all liability.
●Any failure to observe the guidelines in this manual, and any improper
repairs could expose the user to risks (electric shock, energy
hazards, fire hazards) or damage the equipment.
ÊFirst of all, carefully read the safety instructions in chapter "Safety
instructions" on page 11 and following.
ÊMake sure that all necessary manuals (see section "Documentation
overview" on page 6) are available; print the PDF files if required. Most
importantly, you will need the operating manual for the server and the
technical manual for the system board.
ÊShut the server down correctly, switch it off, disconnect the power plugs and
open the server as described in chapter "Preparation" on page 17.
ÊCarry out the expansion or upgrade of your server as described in the
pertinent chapter.
ÊClose the server, connect it to the power outlet, and switch it on as described
in chapter "Completion" on page 37.
ÊStart the operating system and make the appropriate configuration if
necessary (see operating manual).

TX100 S1 Options Guide 11
3 Safety instructions
IThe following safety instructions are also provided in the manual "Safety
notes and other important information".
This device meets the relevant safety regulations for IT equipment. If you have
any questions about whether you can install the server in the intended
environment, please contact your sales outlet or our customer service team.
VCAUTION!
●The actions described in this manual should only be carried out by
technical specialists.
●Equipment repairs should only be performed by service staff. Please
note that unauthorized interference with the system will void the
warranty and exempt the manufacturer from all liability.
●Any failure to observe the guidelines in this manual, and any improper
repairs could expose the user to risks (electric shock, energy
hazards, fire hazards) or damage the equipment.

12 OptionsGuide TX100 S1
Safety instructions
Before starting up
VCAUTION!
●During installation and before operating the device, observe the
instructions on environmental conditions for your device.
●If the device is brought in from a cold environment, condensation may
form both inside and on the outside of the device.
Wait until the device has acclimatized to room temperature and is
absolutely dry before starting it up. Material damage may be caused
to the device if this requirement is not observed.
●Transport the device only in the original packaging or in packaging
that protects it from knocks and jolts.
Installation and operation
VCAUTION!
●The device may only be operated in a maximum ambient temperature
of 35°C.
●If the device is integrated in an installation that receives power from
an industrial (public) power supply network with the IEC309
connector, the (public) power supply protection must comply with the
requirements for non-industrial (public) power supply networks for the
type A connector.
●The unit automatically adjusts itself to a mains voltage in a range of
100 V - 240 V. Ensure that the local mains voltage lies within these
limits.
●This device must only be connected to properly grounded shock-
proof sockets or insulated sockets of the rack's internal power supply
with tested and approved power cables.
●Ensure that the device is connected to a grounded shockproof socket
close to the device.

TX100 S1 Options Guide 13
Safety instructions
VCAUTION!
●Ensure that the power sockets on the device and the grounded
shockproof sockets are freely accessible.
●The On/Off button or the main power switch (if there is one) does not
disconnect the device from the mains voltage. To completely
disconnect it, you must remove all the power plugs from the power
outlets.
●Always connect the server and the attached peripherals to the same
power circuit. Otherwise you run the risk of losing data if, for example,
the server is still running but a peripheral device (e.g. memory
subsystem) fails during a power outage.
●Data cables must be adequately shielded to avoid interference.
●The EN 50173 and EN 50174-1/2 standards apply for LAN cabling.
The minimum requirement is the use of a category 5 screened LAN
cable for 10/100 Mbit/s Ethernet, or a category 5e cable for Gigabit
Ethernet. The requirements from the ISO/IEC 11801 specification
must also be met.
●Route the cables in such a way that they do not form a potential
hazard (tripping) and cannot be damaged. When connecting the
device, refer to the relevant notes in the operating manual.
●Do not connect or disconnect any data transmission cables during a
thunderstorm (lightning hazard).
●Make sure that no objects (e.g. bracelets or paper clips) fall into or
liquids spill into the device (risk of electric shock or short circuit).
●In emergencies (e.g. damaged casing, control elements or power
cable, penetration of liquids or foreign bodies), switch off the device
immediately, unplug it from the grounded power outlets, and contact
your customer service center.

14 OptionsGuide TX100 S1
Safety instructions
VCAUTION!
●Proper operation of the device (in accordance with
IEC 60950-1/EN 60950-1) is only ensured if the casing is fully
assembled and the rear covers for the installation bays are in place
(electric shock, cooling, fire protection, interference suppression).
●Install only system extensions that satisfy the requirements and rules
governing safety, electromagnetic compatibility, and
telecommunications terminal equipment. If you install other
extensions, you may damage the system or violate these safety
regulations. You can find out which system extensions are suitable
from the customer service center or your sales outlet.
●The components marked with a warning label (e.g. lightning symbol)
may only be opened, removed or exchanged by authorized, qualified
personnel.
●If you cause a defect on the device by installing or exchanging system
extensions, the warranty will be invalidated.
●Only set the resolutions and refresh rates specified in the operating
manual for your monitor. Otherwise, you may damage the monitor. If
you are in any doubt, contact your sales outlet or customer service
center.
Batteries
VCAUTION!
●Incorrect replacement of batteries may result in a risk of explosion.
The batteries may only be replaced with identical batteries or with a
type recommended by the manufacturer (see the technical manual for
the system board).
●Replace the lithium-battery on the system board in accordance with
the instructions in the technical manual for the system board.

TX100 S1 Options Guide 15
Safety instructions
Working with CDs/DVDs and CD/DVD drives
When working with devices with CD/DVD drives, these instructions must be
followed.
VCAUTION!
●Only use CDs/DVDs that are in perfect condition in your server's
CD/DVD drive, in order to prevent data loss, equipment damage and
injury.
●Check each CD/DVD for damage, cracks, breakages etc. before
inserting it in the drive.
Note that any additional labels applied may change the mechanical
properties of a CD/DVD and cause imbalance.
Damaged and imbalanced CDs/DVDs can break at high drive speeds
(data loss).
Under certain circumstances, sharp CD/DVD fragments can pierce
the cover of the CD/DVD drive (equipment damage) and can fly out
of the device (danger of injury, particularly to uncovered body parts
such as the face or neck).
IYou can prevent mechanical damage and damage to the CD/DVD drive,
as well as premature CD/DVD wear, by observing the following
suggestions:
– Only insert CDs/DVDs in the drive when needed and remove them
after use.
– Store the CDs/DVDs in suitable sleeves.
– Protect the CDs/DVDs from exposure to heat and direct sunlight.
Laser information
The CD/DVD drive complies with IEC 60825-1 laser class 1.
VCAUTION!
The CD/DVD drive contains a light-emitting diode (LED), which under
certain circumstances produces a laser beam stronger than laser
class 1. Looking directly at this beam is dangerous.
Never remove parts of the CD/DVD drive casing!

16 OptionsGuide TX100 S1
Safety instructions
Modules with Electrostatic-Sensitive Devices
Modules with electrostatic-sensitive devices are identified by the following
sticker:
Figure 1: ESD label
When you handle components fitted with ESDs, you must always observe the
following points:
●Switch off the system and remove the power plugs from the power outlets
before installing or removing components with ESDs.
●You must always discharge static build-up (e.g. by touching a grounded
object) before working with such components.
●Any devices or tools that are used must be free of electrostatic charge.
●Wear a suitable grounding cable that connects you to the external chassis of
the system unit.
●Always hold components with ESDs at the edges or at the points marked
green (touch points).
●Do not touch any connectors or conduction paths on an ESD.
●Place all the components on a pad which is free of electrostatic charge.
IFor a detailed description of how to handle ESD components, see the
relevant European or international standards (EN 61340-5-1,
ANSI/ESD S20.20).

TX100 S1 Options Guide 17
4 Preparation
VCAUTION!
Follow the safety instructions in the chapter "Safety instructions" on
page 11.
4.1 Opening the server
ÊTerminate all applications and shut down the server correctly.
ÊIf your operating system has not switched off the server, press the on/off
button.
ÊSwitch off the power supply unit (use the master switch) and disconnect the
power plug from the grounded shockproof socket.
ÊIf required, remove the lock on the side cover.
ÊLay the server on its left side (as seen from the front).

18 OptionsGuide TX100 S1
Opening the server Preparation
Removing the side cover
Figure 2: Opening the locking lever
ÊPull the locking lever as far as it will go.

TX100 S1 Options Guide 19
Preparation Opening the server
Figure 3: Removing the side cover
ÊLift up the side cover (1).
ÊRemove the side cover (2).
/
0

20 OptionsGuide TX100 S1
Opening the server Preparation
Lifting up the drive cage
Figure 4: Lifting up the drive cage
ÊLoosen the knurled screw (1).
/