Fujitsu PRIMERGY TX100 S2 User manual

Options Guide - English
PRIMERGY TX100 S2
Options Guide
July 2010

Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
email: [email protected].
Certified documentation
according to DIN EN ISO 9001:2008
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2008.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
Copyright © 2010 Fujitsu Technology Solutions GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
– The contents of this manual may be revised without prior notice.
– Fujitsu assumes no liability for damages to third party copyrights or other rights arising from
the use of any information in this manual.
– No part of this manual may be reproduced in any form without the prior written permission
of Fujitsu.
Microsoft, Windows, Windows Server, and Hyper V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.

TX100 S2 Options Guide
Before reading this manual
For your safety
This manual contains important information for safely and correctly using this
product.
Carefully read the manual before using this product. Pay particular attention to
the accompanying manual "Safety Notes and Regulations" and ensure these
safety notes are understood before using the product. Keep this manual and the
manual "Safety Notes and Regulations" in a safe place for easy reference while
using this product.
Radio interference
This product is a "Class A" ITE (Information Technology Equipment). In a
domestic environment this product may cause radio interference, in which case
the user may be required to take appropriate measures. VCCI-A
Aluminum electrolytic capacitors
The aluminum electrolytic capacitors used in the product's printed circuit board
assemblies and in the mouse and keyboard are limited-life components. Use of
these components beyond their operating life may result in electrolyte leakage
or depletion, potentially causing emission of foul odor or smoke.
As a guideline, in a normal office environment (25°C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the product
is used in a hot environment. The customer shall bear the cost of replacing
replaceable components which have exceeded their operating life. Note that
these are only guidelines, and do not constitute a guarantee of trouble-free
operation during the maintenance support period.
High safety use
This product has been designed and manufactured for general uses such as
general office use, personal use, domestic use and normal industrial use. It has
not been designed or manufactured for uses which demand an extremely high
level of safety and carry a direct and serious risk to life or body if such safety
cannot be ensured.

OptionsGuide TX100 S2
These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance control
in weapons systems (hereafter, "high safety use"). Customers should not use
this product for high safety use unless measures are in place for ensuring the
level of safety demanded of such use. Please consult the sales staff of Fujitsu if
intending to use this product for high safety use.
Measures against momentary voltage drop
This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, use of an AC
uninterruptible power supply is recommended.
(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)
Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan
Documents produced by Fujitsu may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.
Harmonic Current Standards
This product conforms to harmonic current standard JIS C 61000-3-2.
Only for the Japanese market:
About SATA hard disk drives
The SATA version of this server supports hard disk drives with SATA / BC-SATA
storage interfaces. Please note that the usage and operation conditions differ
depending on the type of hard disk drive used.
Please refer to the following internet address for further information on the
usage and operation conditions of each available type of hard disk drive:
http://primeserver.fujitsu.com/primergy/harddisk/

TX100 S2 Options Guide
Only for the Japanese market:
IAlthough described in this manual, some sections do not apply to the
Japanese market. These options and routines include:
– USB Flash Module (UFM)

OptionsGuide TX100 S2

TX100 S2 Options Guide
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 Concept and target groups . . . . . . . . . . . . . . . . . . . 9
1.2 Documentation overview . . . . . . . . . . . . . . . . . . . 10
1.3 Expansions and upgrades . . . . . . . . . . . . . . . . . . . 11
1.4 Notational conventions . . . . . . . . . . . . . . . . . . . . 12
2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . 15
4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 23
4.2 Removing the air duct . . . . . . . . . . . . . . . . . . . . . 27
5 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.1 Equipping rules . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.2 Extending/replacing the main memory . . . . . . . . . . . . 31
6 Accessible drives . . . . . . . . . . . . . . . . . . . . . . . 33
6.1 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.2 Installing an accessible 5.25-inch drive . . . . . . . . . . . . 35
7 Non-accessible drives . . . . . . . . . . . . . . . . . . . . . 37
7.1 Installing and removing the hard disk drives . . . . . . . . . 37

OptionsGuide TX100 S2
Contents
8 Expansion cards and parallel interface . . . . . . . . . . . . 43
8.1 Installing an expansion card . . . . . . . . . . . . . . . . . . 45
8.2 Installing a parallel interface cable . . . . . . . . . . . . . . . 47
8.3 Installing TPM (optional) . . . . . . . . . . . . . . . . . . . . 50
8.4 Installing the UFM (optional) . . . . . . . . . . . . . . . . . . 53
9 Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
9.1 Installing the air duct . . . . . . . . . . . . . . . . . . . . . . 55
9.2 Closing the server . . . . . . . . . . . . . . . . . . . . . . . . 56
10 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
10.1 Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

TX100 S2 Options Guide 9
1 Introduction
The PRIMERGY TX100 S2 server is an Intel-based server for workgroups and
small networks. The server is suitable for use as a file server and also as an
application, information or Internet server.
Thanks to its highly developed hardware and software components, the
PRIMERGY TX100 S2 server offers a high level of data security and availability.
Security functions in the BIOS-Setup and on the system board protect the data
on the server against manipulation. The supported RAID levels allow the hard
disk controllers to offer error tolerance, through data redundancy, for users who
want to provide complete protection for valuable data.
Its low noise level and high energy efficiency make it ideal for office
environments.
1.1 Concept and target groups
This Options Guide shows you how to extend and upgrade your server.
VCAUTION!
The activities described in this manual may only be performed by
technical specialists.
IThe installation and removal of the hot-plug components is described in
the Operating Manual supplied with the server.
The PRIMERGY TX100 S2 has a power management function
that reduces power consumption to <65 W in typical
configurations. The server thus satisfies the requirements of the
U.S. Environmental Protection Agency (EPA).

10 OptionsGuide TX100 S2
Introduction
1.2 Documentation overview
More information on your PRIMERGY TX100 S2 can be found in the following
documents:
– "Quick Start Hardware - PRIMERGY TX100 S2" leaflet (included as a
printed copy)
– "Quick Start Software - Quick Installation Guide" DVD booklet (included with
the PRIMERGY ServerView Suite as a printed copy)
– "Safety notes and other important information" manual
– "Warranty" manual
– "Returning used devices" manual
– "Helpdesk" leaflet
– Technical manual for the system board D2779
– "PRIMERGY TX100 S2 Server Operating Manual"
– "PRIMERGY TX100 S2 Server Options Guide"
– "D2779 BIOS Setup Utility for PRIMERGY TX100 S2" manual
IPRIMERGY manuals are available in PDF format on the
ServerView Suite DVD 2. The ServerView Suite DVD 2 is part of the
ServerView Suite supplied with every server.
If you no longer have the ServerView Suite DVDs, you can obtain the
relevant current versions using the order number U15000-C289 (the
order number for the Japanese market: please refer to the configurator
of the server http://primeserver.fujitsu.com/primergy/system.html).
The PDF files of the manuals can also be downloaded free of charge
from the Internet. The overview page showing the online documentation
available on the Internet can be found using the URL (for EMEA market):
http://manuals.ts.fujitsu.com. The PRIMERGY server documentation can
be accessed using the Industry standard servers navigation option.
For the Japanese market please use the URL:
http://primeserver.fujitsu.com/primergy/manual.html.