Fujitsu PRIMERGY TX1330 M4 User manual

Operating Manual - English
FUJITSU Server PRIMERGY TX1330 M4
Operating Manual
October 2018

Copyright and Trademarks
Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
[email protected].
Documentation creation according
to DIN EN ISO 9001:2015
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2015.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright 2018 FUJITSU LIMITED
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
– The contents of this manual may be revised without prior notice.
– Fujitsu assumes no liability for damages to third party copyrights or other rights arising from
the use of any information in this manual.
– No part of this manual may be reproduced in any without the prior written permission of
Fujitsu.
Microsoft, Windows, Windows Server, and Hyper-V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.

TX1330 M4 Operating Manual
Before reading this manual
For your safety
This manual contains important information for safely and correctly using this
product.
Carefully read the manual before using this product. Pay particular attention to
the accompanying manual "Safety Notes and Regulations" and ensure that
these safety notes are understood before using the product. Keep this manual
and the "Safety Notes and Regulations" manual in a safe place for easy
reference while using this product.
Radio interference
This product is a "Class A" ITE (Information Technology Equipment). In a
domestic environment this product may cause radio interference, in which case
the user may be required to take appropriate measures. VCCI-A
Aluminum electrolytic capacitors
The aluminum electrolytic capacitors used in the printed circuit board
assemblies of the product and in the mouse and keyboard are limited-life
components. Use of these components beyond their operating life may result in
electrolyte leakage or depletion, potentially causing emission of foul odor or
smoke.
As a guideline, in a normal office environment (25°C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the
product is used in a hot environment. The customer shall bear the cost of
replacing replaceable components which have exceeded their operating life.
Note that these are only guidelines, and do not constitute a guarantee of
trouble-free operation during the maintenance support period.
High safety use
This product has been designed and manufactured to be used in commercial
and/or industrial areas as a server.
When used as visual display workplace, it must not be placed in the direct field
of view to avoid incommoding reflections (applies only to TX server systems).

Operating Manual TX1330 M4
The device has not been designed or manufactured for uses which demand an
extremely high level of safety and carry a direct and serious risk of life or body
if such safety cannot be assured.
These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance
control in weapons systems (hereafter, "high safety use"). Customers should
not use this product for high safety use unless measures are in place for
ensuring the level of safety demanded of such use. Please consult the sales
staff of Fujitsu if intending to use this product for high safety use.
Measures against momentary voltage drop
This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, the use of an
uninterruptible power supply is recommended.
(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)
Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan
Documents produced by Fujitsu may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.

TX1330 M4 Operating Manual
Harmonic Current Standards
This product conforms to harmonic current standard JIS C 61000-3-2.
Only for Japan:
About SATA HDDs
The SATA version of this server supports HDDs with SATA/BC-SATA storage
interfaces. Please note that the usage and operation conditions differ
depending on the type of HDD used.
For more information on the usage and operation conditions of each available
type of HDD, see the following internet address:
http://jp.fujitsu.com/platform/server/primergy/harddisk/

Operating Manual TX1330 M4

TX1330 M4 Operating Manual
Content
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.1 Notational conventions . . . . . . . . . . . . . . . . . . . . 11
2 Before you start . . . . . . . . . . . . . . . . . . . . . . . . 13
2.1 Documentation overview . . . . . . . . . . . . . . . . . . . 13
3 Product description . . . . . . . . . . . . . . . . . . . . . . 17
3.1 Overview of the server . . . . . . . . . . . . . . . . . . . . . 18
3.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.3 Connectors, controls and indicators . . . . . . . . . . . . . 28
3.3.1 Connectors on the server . . . . . . . . . . . . . . . . . . . . 28
3.3.1.1 Server front . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.3.1.2 Server rear . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.3.2 Controls and indicators on the server front . . . . . . . . . . . 30
3.3.2.1 Controls on the front panel . . . . . . . . . . . . . . . . . . 30
3.3.2.2 Indicators on the front panel . . . . . . . . . . . . . . . . . 31
3.3.2.3 Indicator on the ODD . . . . . . . . . . . . . . . . . . . . . 35
3.3.2.4 Indicators on the hot-plug HDD/SSD module . . . . . . . . 36
3.3.3 Indicators on the server rear . . . . . . . . . . . . . . . . . . . 37
3.3.3.1 Indicators on the I/O panel . . . . . . . . . . . . . . . . . . 37
3.3.3.2 Indicator on hot-plug PSU . . . . . . . . . . . . . . . . . . 40
3.3.3.3 Indicator on FJBU . . . . . . . . . . . . . . . . . . . . . . 41
4 Important information . . . . . . . . . . . . . . . . . . . . . 43
4.1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . 43
4.2 ENERGY STAR . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.3 CE conformity . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.4 FCC Class A Compliance Statement . . . . . . . . . . . . . 53
4.5 Environmental protection . . . . . . . . . . . . . . . . . . . 54

Operating Manual TX1330 M4
Content
5 Starting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
5.1 Installation steps, overview . . . . . . . . . . . . . . . . . . . 58
5.2 Unpacking the server . . . . . . . . . . . . . . . . . . . . . . 60
5.3 Setting up the floorstand model . . . . . . . . . . . . . . . . 61
5.3.1 Installing the anti-tilt bracket . . . . . . . . . . . . . . . . . . . 62
5.4 Installing the server in the rack . . . . . . . . . . . . . . . . . 64
5.4.1 Installing the server in the rack . . . . . . . . . . . . . . . . . . 66
5.5 Connecting cables . . . . . . . . . . . . . . . . . . . . . . . . 68
5.5.1 Notes on connecting/disconnecting cables . . . . . . . . . . . . 68
5.5.2 Connecting devices to the server . . . . . . . . . . . . . . . . . 69
5.5.3 Connecting the power cord . . . . . . . . . . . . . . . . . . . . 70
5.5.3.1 Using cable ties (standard PSU) . . . . . . . . . . . . . . . 70
5.5.3.2 Using the cable clamp . . . . . . . . . . . . . . . . . . . . . 72
5.6 Switching the server on for the first time . . . . . . . . . . . 73
5.7 Configuring the server with
ServerView Installation Manager . . . . . . . . . . . . . . . . 74
5.7.1 Configuring the server and installing the operating system . . . . 74
5.7.1.1 Configuring the controllers . . . . . . . . . . . . . . . . . . 75
5.7.1.2 Installing the operating system . . . . . . . . . . . . . . . . 75
5.8 Configuring the server without
ServerView Installation Manager . . . . . . . . . . . . . . . . 75
5.8.1 Configuring the server and installing the operating system . . . . 75
5.8.1.1 Configuring the onboard SAS/SATA controller . . . . . . . . 75
5.8.1.2 Installing the operating system . . . . . . . . . . . . . . . . 75
5.9 Notes on configuring controllers . . . . . . . . . . . . . . . . 77
5.9.1 Notes on onboard SATA controllers . . . . . . . . . . . . . . . . 77
5.9.2 Notes on SAS/SATA RAID controllers . . . . . . . . . . . . . . 77
5.10 Note on operating system . . . . . . . . . . . . . . . . . . . 78
6 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
6.1 Switching the server on and off . . . . . . . . . . . . . . . . 79
6.2 Access to the drives (floorstand model) . . . . . . . . . . . . 82
6.2.1 Removing the drive covers . . . . . . . . . . . . . . . . . . . . 82

TX1330 M4 Operating Manual 9
Content
6.3 Installing HDD/SSD modules . . . . . . . . . . . . . . . . . 85
6.3.1 Installing 2.5-inch HDD/SSD modules . . . . . . . . . . . . . . 85
6.3.1.1 Removing a 2.5-inch HDD/SSD dummy module . . . . . . . 85
6.3.1.2 Installing a 2.5-inch HDD/SSD module . . . . . . . . . . . . 86
6.3.2 Installing 3.5-inch HDD modules . . . . . . . . . . . . . . . . 87
6.3.2.1 Removing a 3.5-inch HDD dummy module . . . . . . . . . 87
6.3.2.2 Installing a 3.5-inch HDD/SSD module . . . . . . . . . . . . 87
6.4 Installing a second PSU . . . . . . . . . . . . . . . . . . . . 89
6.4.1 Removing the dummy cover . . . . . . . . . . . . . . . . . . . 89
6.4.2 Installing a PSU . . . . . . . . . . . . . . . . . . . . . . . . . 90
6.5 Cleaning the server . . . . . . . . . . . . . . . . . . . . . . 91
7 Troubleshooting and tips . . . . . . . . . . . . . . . . . . . 93
8 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . 101
9 Warranty and service . . . . . . . . . . . . . . . . . . . . . . 109

10 Operating Manual TX1330 M4
Content