Fujitsu PRIMERGY TX120 S2 User manual

PRIMERGY TX120 S2 Server
Options Guide
Edition April 2009

Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
[email protected].
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
Copyright © 2009 Fujitsu Technology Solutions GmbH.
All rights are reserved.
Delivery subject to availability. The right to technical modification is reserved.
All hardware and software names used are trade names and/or trademarks of their respective
manufacturers.

TX120 S2 Options Guide
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 ENERGY STAR . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Concept and target groups . . . . . . . . . . . . . . . . . . . 6
1.3 Documentation overview . . . . . . . . . . . . . . . . . . . . 7
1.4 Expansions and conversions . . . . . . . . . . . . . . . . . . 9
1.5 Notational conventions . . . . . . . . . . . . . . . . . . . . 10
2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 19
4.2 Removing the crosspiece . . . . . . . . . . . . . . . . . . . 20
4.3 Removing the drive cage . . . . . . . . . . . . . . . . . . . 21
5 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.1 Equipping rules . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.2 Expanding/replacing the main memory . . . . . . . . . . . . 25
6 Accessible drives . . . . . . . . . . . . . . . . . . . . . . . 27
6.1 Installing an HDD extension box . . . . . . . . . . . . . . . 27
6.2 Installing a backup drive . . . . . . . . . . . . . . . . . . . . 31
7 Expansion cards in the PCI slots . . . . . . . . . . . . . . . 37

OptionsGuide TX120 S2
Contents
7.1 PCI slot overview . . . . . . . . . . . . . . . . . . . . . . . . 37
7.2 Installing an expansion card . . . . . . . . . . . . . . . . . . 38
8 Trusted Platform Module (TPM) . . . . . . . . . . . . . . . . . 45
9 Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
9.1 Installing the drive cage . . . . . . . . . . . . . . . . . . . . . 41
9.2 Installing the crosspiece . . . . . . . . . . . . . . . . . . . . 43
9.3 Assembling the server . . . . . . . . . . . . . . . . . . . . . 44
10 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
10.1 Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

TX120 S2 Options Guide 5
1 Introduction
The PRIMERGY TX120 S2 server is an Intel-based server for small and
medium-sized networks and can be used in the horizontal position or as a
desktop model.
The PRIMERGY TX120 S2 server features exceptionally low energy
consumption, very quiet running and a compact size. As a result, it is also the
ideal solution for home and small offices.
Thanks to its highly developed hardware and software components, the
PRIMERGYTX120 S2serveroffersahighlevel ofdatasecurityandavailability.
These include hot-plug HDD modules, the ServerView server management
software, Prefailure Detection and Analysing (PDA) and Automatic Server
Reconfiguration and Restart (ASR&R).
Security functions in the BIOS-setup protect the data on the server against
manipulation. Additional security is provided by the lockable drive cover.

6 OptionsGuide TX120 S2
ENERGY STAR Introduction
1.1 ENERGY STAR
1.2 Concept and target groups
This Options Guide shows you how to extend and upgrade your server.
VCAUTION!
The activities described in this manual may only be performed by
technical specialists.
IThe installation and removal of the hot-plug components is described in
the Operating Manual supplied with the server.
In some particular configurations1the PRIMERGY TX120 S2 is
equipped with a power management system which, in energy-
saving mode, reduces the power consumption to <65 W. The
server thus satisfies the requirements of the U.S. Environmental
Protection Agency (EPA).
The EPA estimates that computer systems use around 5 % of all
electricity in the office sector and that this figure is growing
rapidly. If all computer systems and peripherals were placed in
energy-saving mode when not in use, the overall savings in
electricity could amount to some US $ 2 billion annually. These
savings would also prevent the emission of 20 million tons of
carbon dioxide into the atmosphere - equivalent to theemissions
from 5 million automobiles.
As an ENERGY STAR partner, Fujitsu Technology Solutions
GmbH has determined that in some particular configurations this
product meets the ENERGY STAR guidelines for energy
efficiency.
1These servers are always delivered with a particular setting in the BIOS setup. For details
please see the manual “D2785 BIOS Setup Utility for PRIMERGY TX120 S2” on the
PRIMERGY ServerView Suite DVD 2.

TX120 S2 Options Guide 7
Introduction Documentation overview
1.3 Documentation overview
More information on your PRIMERGY TX120 S2 can be found in the following
documents:
– “Quick Start Hardware - PRIMERGY TX120 S2” leaflet (only included as a
printed copy)
– “Quick Start Software - Quick Installation Guide” DVDbooklet (only included
with the PRIMERGY ServerView Suite as a printed copy)
– “Safety notes and other important information” manual
– “Warranty” manual
– “PRIMERGY ServerView Suite Local Service Concept - LSC” manual
– “Returning used devices” manual
– “Helpdesk” leaflet
– Technical manual for the system board D2785
– “PRIMERGY TX120 S2 Server Operating Manual”
– “PRIMERGY TX120 S2 Server Options Guide”
– “D2785 BIOS Setup Utility für PRIMERGY TX120 S2“ manual
IFurther information on SAS/SATA RAID controllers is provided in the
“Modular RAID Controller Installation Guide” (on PRIMERGY
ServerViewSuiteDVD 2underIndustry Standard Servers -Expansion Cards
- Storage Adapters - LSI RAID / SCSI Controllers).
Further information on other SAS/SATA RAID controllers (e.g. for
operatingexternalSAS/SATA harddisk drives ortapedrives)is available
on PRIMERGY ServerView Suite DVD 2 under Industry Standard Servers
- Expansion Cards - Storage Adapters - LSI RAID / SCSI Controllers.

8 OptionsGuide TX120 S2
Documentation overview Introduction
IPRIMERGY manuals are available in PDF format on the PRIMERGY
ServerView Suite DVD 2. The PRIMERGY ServerView Suite DVD 2 is
part of the PRIMERGY ServerView Suite supplied with every server.
If you no longer have the ServerView Suite DVDs, you can obtain the
relevant current versions using the order number U15000-C289.
The PDF files of the manuals can also be downloaded free of charge
from the Internet. The overview page showing the online documentation
available on the Internet can be found using the URL:
http://manuals.ts.fujitsu.com. The PRIMERGY server documentation can
be accessed using the Industry standard servers navigation option.
Further sources of information:
– PRIMERGY Abbreviations and Glossary on the PRIMERGY
ServerView Suite DVD 2
– Manual for the monitor
– Documentation for the boards and drives
– Operating system documentation
– Information files in your operating system

TX120 S2 Options Guide 9
Introduction Expansions and conversions
1.4 Expansions and conversions
Main memory expansion
The system board supports up to 16 Gbyte of main memory. 4 slots (2 memory
banks with 2 slots each) are provided for the main memory. Each memory bank
can be equippeded with 1 GB, 2 GB or 4 GB unbuffered DDR2 memory
modules.
If the memory modules are installed in pairs, they must be identical (2-way inter-
leaved mode).
Additional accessible drive
A 3.5-inch bay for an HDD extension box or a backup drive is available.
Expansion cards in the PCI slots
The following PCI slots are provided by the system board:
PCI slot Description
1 PCI Express x8 slot
2 PCI Express x8 slot
3 PCI slot (32-bit/33MHz)
4 PCI Express x8 slot

10 OptionsGuide TX120 S2
Notational conventions Introduction
1.5 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands or menu items.
“Quotation marks” indicate names of chapters and terms that are being
emphasized.
Êdescribes activities that must be performed in the order
shown.
VCAUTION! pay particular attention to texts marked with this symbol.
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips.

TX120 S2 Options Guide 11
2 Procedure
VCAUTION!
●The actions described in this manual should only be performed by
technical specialists.
●Repairs to the device must only be carried out by service personnel.
Please note that unauthorized interference with the system will void
the warranty and exempt the manufacturer from all liability.
●Anyfailureto observe theguidelinesinthismanual,andanyimproper
repairs could expose the user to risks (electric shock, energy
hazards, fire hazards) or damage the equipment.
ÊFirst of all, carefully read the safety instructions in the chapter “Safety” on
page 13.
ÊMake sure that all necessary manuals (see the section “Documentation
overview” on page 7) are available; print the PDF files if required. Most
importantly, you will need the operating manual for the server and the
technical manual for the system board.
ÊShut the server down correctly, switch it off, disconnect the power plugs and
open the server as described in thechapter “Preparation” on page 19 .
ÊCarry out the expansion or upgrade of your server as described in the
pertinent chapter.
IInstallation and removal of the hot-plug components are described in
the operating manual.
ÊClosethe server, connectit tothe poweroutlet, and switch iton asdescribed
in the chapter “Completion” on page 41.
ÊStart the operating system and make the appropriate configuration if
necessary (see the operating manual).

TX120 S2 Options Guide 13
3Safety
IThe following safety instructions are also provided in the manual “Safety
notes and other important information”.
This device meets the relevant safety regulations for IT equipment. If you have
any questions about whether you can install the server in the intended
environment, please contact your sales outlet or our customer service team.
VCAUTION!
●The actions described in this manual should only be performed by
technical specialists.
●Repairs to the device that do not relate to CSS failures must only be
carried out by service personnel. Please note that unauthorized inter-
ference with the system will void the warranty and exempt the
manufacturer from all liability.
●Anyfailureto observe theguidelinesinthismanual,andanyimproper
repairs could expose the user to risks (electric shock, energy
hazards, fire hazards) or damage the equipment.

14 OptionsGuide TX120 S2
Safety
Before starting up
VCAUTION!
●During installation and before operating the device, observe the
instructions on environmental conditions for your device.
●Ifthedevice is brought in fromacold environment,condensationmay
form both inside and on the outside of the device.
Wait until the device has acclimatized to room temperature and is
absolutely dry before starting it up. Material damage may be caused
to the device if this requirement is not observed.
●Transport the device only in the original packaging or in packaging
that protects it from knocks and jolts.
Installation and operation
VCAUTION!
●This unit should not be operated in ambient temperatures above
35 °C.
●If the unit is integrated into an installation that draws power from an
industrial power supply network withan IEC309 connector, the power
supply's fuse protection must comply with the requirements for non-
industrial power supply networks for type A connectors.
●The unit automatically adjusts itself to a mains voltage in a range of
100 V - 240 V. Ensure that the local mains voltage lies within these
limits.
●This device must only be connected to properly grounded shock-
proof sockets or insulated sockets of the rack's internal power supply
with tested and approved power cables.
●Ensure that the device is connectedto a grounded shockproof socket
close to the device.

TX120 S2 Options Guide 15
Safety
VCAUTION!
●Ensure that the power sockets on the device and the grounded
shockproof sockets are freely accessible.
●The On/Off button or the main power switch (if present) does not
isolate the device from the mains power supply. To disconnect it
completely from the mains power supply, unplug all network power
plugs from the grounded shockproof sockets.
●Always connect the server and the attached peripherals to the same
powercircuit.Otherwiseyou run theriskoflosing dataif,for example,
the server is still running but a peripheral device (e.g. memory
subsystem) fails during a power outage.
●Data cables must be adequately shielded.
●The EN 50173 and EN 50174-1/2 standards apply for LAN cabling.
The minimum requirement is the use of a category 5 screened LAN
cable for 10/100 Mbit/s Ethernet, or a category 5e cable for Gigabit
Ethernet. The requirements from the ISO/IEC 11801 specification
must also be met.
●Route the cables in such a way that they do not create a potential
hazard (make sure no-one can trip over them) and that they cannot
be damaged. When connecting the server, refer to the relevant
instructions in this manual.
●Never connect or disconnect data transmission lines during a storm
(risk of lightning strike).
●Make sure that no objects (e.g. jewelry, paperclips etc.) or liquids can
get inside the server (risk of electric shock, short circuit).
●Inemergencies(e.g.damagedcasing,controlsorcables,penetration
of liquids or foreign bodies), switch off the server immediately,
remove all power plugs and contact your sales outlet or customer
service team.

16 OptionsGuide TX120 S2
Safety
VCAUTION!
●Proper operation of the system (in accordance with IEC 60950-1/
EN 60950-1) is only ensured if the casing is completely assembled
and the rear covers for the installation slots have been fitted (electric
shock, cooling, fire protection, interference suppression).
●Only install system expansions that satisfy the requirements and
rules governing safety and electromagnetic compatibility and those
relating to telecommunication terminals. If you install other expan-
sions, they may damage the system or violate the safety regulations.
Informationonwhichsystem expansionsareapprovedforinstallation
can be obtained from our customer service center or your sales
outlet.
●Thecomponentsmarkedwithawarningnotice(e.g.lightningsymbol)
may only be opened, removed or exchanged by authorized, qualified
personnel. Exception: CCS components can be replaced.
●The warranty is void if the server is damaged during installation or
replacement of system expansions.
●Only set screen resolutions and refresh rates thatare specified in the
operating manual for the monitor. Otherwise, you may damage your
monitor. If you are in any doubt, contact your sales outlet or customer
service center.
Batteries
VCAUTION!
●Incorrect replacement of batteries may result in a risk of explosion.
The batteries may only be replaced with identical batteries or with a
typerecommendedbythemanufacturer(seethetechnicalmanualfor
the system board).
●Replace the lithium-battery on the system board in accordance with
the instructions in the technical manual for the system board.

TX120 S2 Options Guide 17
Safety
Working with CDs/DVDs and CD/DVD drives
When working with devices with CD/DVD drives, these instructions must be
followed.
VCAUTION!
●Only use CDs/DVDs that are in perfect condition in your server's
CD/DVD drive, in order to prevent data loss, equipment damage and
injury.
●Check each CD/DVD for damage, cracks, breakages etc. before
inserting it in the drive.
Note that any additional labels applied may change the mechanical
properties of a CD/DVD and cause imbalance.
DamagedandimbalancedCDs/DVDscanbreakathigh drivespeeds
(data loss).
Under certain circumstances, sharp CD/DVD fragments can pierce
the cover of the CD/DVD drive (equipment damage) and can fly out
of the device (danger of injury, particularly to uncovered body parts
such as the face or neck).
IYou can prevent mechanical damage and damage to the CD/DVD drive,
as well as premature CD/DVD wear, by observing the following sugges-
tions:
– Only insert CDs/DVDs in the drive when needed and remove them
after use.
– Store the CDs/DVDs in suitable sleeves.
– Protect the CDs/DVDs from exposure to heat and direct sunlight.
Laser information
The CD/DVD drive complies with IEC 60825-1 laser class 1.
VCAUTION!
The CD/DVD drive contains a light-emitting diode (LED), which under
certain circumstances produces a laser beam stronger than laser
class 1. Looking directly at this beam is dangerous.
Never remove parts of the CD/DVD drive casing!

18 OptionsGuide TX120 S2
Safety
Modules with electrostatic-sensitive components
Systems and components that might be damaged by electrostatic discharge
(ESD) are marked with the following label:
Figure 1: ESD label
When you handle components fitted with ESDs, you must observe the following
points under all circumstances:
●Remove the power plug before installing or removing components
containing ESDs.
●You must always discharge yourself of static charges (e.g. by touching a
grounded object) before working.
●The equipment and tools you use must be free of static charges.
●Only touch the components at the positions highlighted in green (touch
points).
●Do not touch any exposed pins or conductors on a component.
●Use a grounding cable designed for this purpose to connect yourself to the
system unit as you install components.
●Place all components on a static-safe base.
IYou will find a detailed description for handling ESD components in the
relevant European or international standards (DIN EN 61340-5-1,
ANSI/ESD S20.20).

TX120 S2 Options Guide 19
4Preparation
VCAUTION!
Please note the safety instructions in chapter “Safety” on page 13.
4.1 Opening the server
ÊExit all applications and shut down the server properly.
ÊPress the On/Off button if the server has not been switched off by the
operating system.
ÊUnplug all power plugs.
ÊDisconnect all cables on the rear of the server.
Figure 2: Opening the server
ÊRemovethestabilizersfromtheserver(seeoperatingmanual)andplacethe
server on its four rubber feet (1), if the server is operated in the vertical
position.
ÊPress and hold in the locks on both sides of the server (2), push the top
cover forwards and lift it up and off (3).
1
2
3

20 OptionsGuide TX120 S2
Removing the crosspiece Preparation
4.2 Removing the crosspiece
Figure 3: Removing the crosspiece
ÊPull the crosspiece out a little to the side (1).
ÊUnhook the crosspiece on the left (2).
ÊCarefully remove the crosspiece.
2
1