Fujitsu PRIMERGY TX150 S5 Owner's manual

PRIMERGY
PRIMERGY TX150 S5
Server
Service Supplement
Susanne Däschlein
Fujitsu Siemens Computers GmbH München
81730 München
e-mail: email: [email protected]
Tel.: [phone]
Fax: (++49) 700 / 372 00000
TX150 S5
Sprachen: En
Edition September 2006

Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Fax forms for sending us your comments are included in
the back of the manual.
There you will also find the addresses of the relevant
User Documentation Department.
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademar s
Copyright © 2006 Fujitsu Siemens Computers GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.

TX150 S5 Service Supplement
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Overview of the documentation . . . . . . . . . . . . . . . . . . 5
1.2 Notational conventions . . . . . . . . . . . . . . . . . . . . . . 8
2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3 Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4 Replacement routines . . . . . . . . . . . . . . . . . . . . . 17
4.1 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.1.1 Floorstand model . . . . . . . . . . . . . . . . . . . . . . . . 17
4.1.1.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 17
4.1.1.2 Removing the front cover . . . . . . . . . . . . . . . . . . . . 17
4.1.2 Rack model . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.1.2.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 18
4.1.2.2 Removing the rack front cover . . . . . . . . . . . . . . . . . . 19
4.2 Replacing the operating panel module . . . . . . . . . . . . . 19
4.3 Replacing the DVD/DVD-RW drive . . . . . . . . . . . . . . . 20
4.4 Replacing the system fan . . . . . . . . . . . . . . . . . . . . 22
4.5 Replacing the standard PS . . . . . . . . . . . . . . . . . . . 24
4.6 Replacing the Power backplane . . . . . . . . . . . . . . . . . 26
4.7 Replacing the SAS/SATA backplane . . . . . . . . . . . . . . 27
4.8 Replacing the IDTEMP combo . . . . . . . . . . . . . . . . . 29
4.9 Replacing the intrusion switches . . . . . . . . . . . . . . . . 30
4.10 Replacing the processor . . . . . . . . . . . . . . . . . . . . 32
4.11 Replacing the system board . . . . . . . . . . . . . . . . . . . 38
5 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
5.1 Board layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
5.1.1 Operating panel board . . . . . . . . . . . . . . . . . . . . . 43
5.1.2 SAS/SATA backplane . . . . . . . . . . . . . . . . . . . . . . 44
5.1.3 Power backplane . . . . . . . . . . . . . . . . . . . . . . . . 45
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

TX150 S5 Service Supplement 5
1Introduction
The PRIMERGY TX150 S5 Server is an Intel-based server for medium-and
large-sized networks. The server is suitable for use as a file server as well as an
application, information, or Internet server. It is available as a floorstand or rack
model. The floorstand model can be converted to a rack model using an optional
conversion kit.
1.1 Overview of the documentation
Concept and target groups
This Service Supplement completes the information given in the Operating
Manual, the Options Guide and the Technical Manual of the system board.
The activities described in this manual may only be performed by service
personnel.
Service DVD
Service partners of Fujitsu Siemens can order a Service DVD PRIMERGY. On
the DVD the following manuals are available in pdf format:
– The “Safety notes and other important information” manual
– The Operating Manual for PRIMERGY TX150 S5
– The Technical Manual for the system board D2399
– The Options Guide for PRIMERGY TX150 S5
– The Service Supplement PRIMERGY TX150 S5
– The “BIOS Setup” manual

6 Service Supplement TX150 S5
Overview of the documentation Introduction
Information/procedure Manual
Detailed safety notes Safety Manual
Features and technical data of the server Operating Manual
Installation and operation, among other things:
– External ports
– Operation
– Configuration of the server
– Installation of the rack mounting kit
Troubleshooting
Installation/removal of all hot-plug components:
– hot-plug power supply units
– hot-plug hard disk drives
Information about the system board:
– Features of the system board
– Board layout
– Jumper settings
–LEDdisplays
– Replacing the battery
Technical Manual
Table 1: Overview of the documentation TX150 S5

TX150 S5 Service Supplement 7
Introduction Overview of the documentation
Extensions and upgrades:
IFor some components only the installation
routine is described in the Options Guide.
Removing this components proceed in
reverse order.
– Extending/replacing the main memory
– Installing accessible drives, like floppy disk
drive, DVD/DVD-RW drive etc.
– Installing the SAS hard disks extension box
– Installing controller in the PCI slots
– Installing the RAID key
– Installing the COM2 interface
– Installing the parallel interface
– Conversion standard PS to hot-plug PS
– Converting from the floorstand model to the
rack model
Options Guide
Cabling
Replacement routines:
– Replacing the operating panel
– Replacing the system fan
– Replacing the standard PS
– Replacing the Power backplane
– Replacing the SAS/SATA backplane
– Replacing the IDTEMP Combo
– Replacing the intrusion switches
– Replacing the processor
– Replacing the system board
Service Supplement
Board layout
BIOS setup BIOS Setup
Information/procedure Manual
Table 1: Overview of the documentation TX150 S5

8 Service Supplement TX150 S5
Notational conventions Introduction
1.2 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands, menu items or software programs.
„Quotation marks“ indicate names of chapters and terms that are being
emphasized.
Êdescribes activities that must be performed in the order
shown.
VCAUTION! pay particular attention to texts marked with this symbol.
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips.
Table 2: Notational conventions

TX150 S5 Service Supplement 9
2Procedure
VCAUTION!
The actions described in these instructions should only be performed by
service personnel.
ÊFirst of all please familiarize yourself with the safety instructions in the
section chapter “Safety notes” on page 11 et seq. .
ÊEnsure that all required manuals (see Service DVD) are available, printing
out the PDF files if necessary. You will definitely need the Operating Manual
for the server, the Options Guide for the server and the Technical Manual for
the system board.
ÊShut down the server correctly, switch it off, pull out the power plug, and
open the server as described in the chapter “Replacement routines” on
page 17 et seq. .
ÊReplace the defective component as described in the relevant chapter.
IProcedures which are identical for the floorstand and rack models are
only described for the floorstand model.
ÊClose the server.1
ÊConnect the cables. 1
ÊConnect the server to the power outlet.1
ÊStart the operating system.1
ÊIf necessary, configure the server as required.1
1This procedures are described in the Operating Manual.

TX150 S5 Service Supplement 11
3 Safety notes
IThe following safety notes are also provided in the “Safety notes and
other important information” manual.
This device complies with the relevant safety regulations for data processing
equipment.
VCAUTION!
The actions described in these instructions should only be performed by
service personnel.
Before operating the device
VCAUTION!
●During installation and before operating the device, observe the
instructions on environmental conditions for your device.
●If the device is brought in from a cold environment, condensation may
form both inside and on the outside of the machine.
Wait until the device has acclimatized to room temperature and is
absolutely dry before starting it up. Material damage may be caused
to the device if this requirement is not observed.
●Transport the device only in the original packaging or in packaging
that protects it from knocks and jolts.
Installation and operation
VCAUTION!
●If the rack model is integrated in an installation that receives power
from an industrial (public) power supply network with the IEC309
connector, the (public) power supply protection must comply with the
requirements for the non-industrial (public) power supply networks for
the type A connector.
●The server automatically sets itself to a voltage in the range of
100 V to 240 V. Make sure that your local voltage is within this range.

12 Service Supplement TX150 S5
Safety notes
VCAUTION!
●This device has a specially approved power cable and must only be
connected to a grounded insulated socket.
●Ensure that the power socket on the device or the grounded wall
outlet is freely accessible.
●The ON/OFF button does not disconnect the device from the mains
voltage. To disconnect the line voltage completely, remove the power
plug(s) from the grounded insulated socket(s).
●Always connect the device and the attached peripherals to the same
power circuit. Otherwise you run the risk of losing data if, for example,
the central processing unit is still running but the peripheral device
(e.g. storage subsystem) has failed during a power outage.
●Data cables to peripheral devices must be adequately shielded.
●To the LAN wiring the requirements apply in accordance with the
standards EN 50173 and EN 50174-1/2. As minimum requirement
the use of a protected LAN line of category 5 for 10/100 MBps
Ethernet, and/or of category 5e for Gigabit Ethernet is considered.
The requirements of the specification ISO/IEC 11801 are to be
considered.
●Route the cables in such a way that they do not form a potential
hazard (make sure no-one can trip over them) and that they cannot
be damaged. When connecting up a device, refer to the relevant
notes in this manual.
●Never connect or disconnect data transmission lines during a storm
(lightning hazard).
●Make sure that no objects (such as bracelets or paper clips) fall into
or liquids spill into the device (risk of electric shock or short circuit).
●In emergencies (e.g. damaged casing, controls or cables, penetration
of liquids or foreign matter), switch off the device immediately, remove
the power plug and contact your sales outlet or customer service
team.

TX150 S5 Service Supplement 13
Safety notes
VCAUTION!
●Proper operation of the device (in accordance with IEC 60950/
EN 60950) is only ensured if the casing is completely assembled and
the rear covers for the installation openings have been put in place
(electric shock, cooling, fire protection, interference suppression).
●Only install system expansions that satisfy the requirements and
rules governing safety and electromagnetic compatibility and relating
to telecommunications terminal equipment. If you install other expan-
sions, you may damage the system or violate the safety regulations
and regulations governing RFI suppression. Information on which
system expansions are suitable can be obtained from the customer
service centre or your sales outlet.
●The components or parts marked with a warning label (e.g. lightning
symbol) may only be opened, removed or exchanged by authorized,
qualified personnel. The hot-plug power supply units are exceptions
to this rule.
●The warranty expires if the device is damaged during the installation
or replacement of system expansions.
●You may only set those resolutions and refresh rates specified in the
„Technical data“ section of the monitor description. Otherwise, you
may damage your monitor. If you are in any doubt, contact your sales
outlet or customer service centre.
Batteries
VCAUTION!
●Incorrect replacement of batteries may lead to a risk of explosion. The
batteries may only be replaced with identical batteries or with a type
recommended by the manufacturer (see the Technical Manual for the
system board).
●Do not throw batteries into the trash can. They must be disposed of
in accordance with local regulations concerning special waste.
●The battery must be disposed of in accordance with local regulations
concerning special waste.

14 Service Supplement TX150 S5
Safety notes
VCAUTION!
●Replace the lithium battery on the system board in accordance with
the instructions in the Technical Manual for the system board.
●All batteries containing pollutants are marked with a symbol (a
crossed-out garbage can). In addition, the marking is provided with
the chemical symbol of the heavy metal decisive for the classification
as a pollutant:
Cd Cadmium
Hg Mercury
Pb Lead
Notes on handling CDs and CD-/DVD-ROM drives
VCAUTION!
●Use only CDs in proper condition in the CD-/DVD-ROM drive of your
server to prevent data loss, damage to the device and injuries.
●Therefore, check each CD for damage, cracks, breakage etc. before
inserting it in the drive.
Please note that any additional labels applied may change the
mechanical properties of a CD and cause imbalance.
Damaged and imbalanced CDs can break at high drive speeds (data
loss).
Under certain conditions sharp-edged pieces of broken CDs can
penetrate the cover of the drive (damage to the device) and be thrown
out of the device (danger of injury, particularly on uncovered body
parts such as the face or neck).
IYou protect the CD-/DVD-ROM drive and prevent mechanical damage,
as well as premature wearing of the CDs, by observing the following
suggestions:
– Only insert the CDs in the drive when needed and remove them after
use.
– Store the CDs in suitable sleeves.
– Protect the CDs from exposure to heat and direct sunlight.

TX150 S5 Service Supplement 15
Safety notes
Note about the laser
The CD-/DVD-ROM drive is classified for laser class 1according to
IEC 60825-1.
VCAUTION!
The CD-/DVD-ROM drive contains a laser diode (LED). Sometimes the
LED produces a stronger laser beam than laser class 1. Direct view into
this laser beam is dangerous.
Never remove parts of the CD-/DVD-ROM drive assembly!
Modules with electrostatic-sensitive components:
Systems and components that might be damaged by electrostatic discharge
(ESD) are marked with the following label:
Figure 1: ESD label
When you handle components fitted with ESDs, you must observe the following
points under all circumstances:
●Remove the power plug from the power socket before inserting or removing
components containing ESDs.
●You must always discharge yourself of static charges (e.g. by touching a
grounded object) before working.
●The equipment and tools you use must be free of static charges.
●Only touch the components at the positions highlighted in green (touch
points).
●Do not touch any exposed pins or conductors on a component.

16 Service Supplement TX150 S5
Safety notes
●Use a grounding cable designed for this purpose to connect yourself to the
system unit as you install components.
●Place all components on a static-safe base.
IYou will find a detailed description for handling ESD components in the
relevant European or international standards (DIN EN 61340-5-1,
ANSI/ESD S20.20).

TX150 S5 Service Supplement 17
4 Replacement routines
VCAUTION!
Observe the safety instructions in the chapter “Safety notes” on page 11
et seq. .
4.1 Preparation
4.1.1 Floorstand model
IYou will find a detailed description of “Opening the server“ and
“Removing the front cover“ in the Options Guide TX150 S5.
4.1.1.1 Opening the server
ÊTerminate all applications and shut down the server correctly.
ÊIf your operating system has not switched off the server, press the on/off
switch for at least four seconds (“Power override“ function).
ÊPull all power connectors out of the power outlets.
ÊIf required, remove the lock on the side cover.
ÊUnlock the server.
ÊLoosen the two screws at the server’s rear side.
ÊPush back the left-hand side cover approxiate 2 cm.
ÊRemove the left-hand side cover.
4.1.1.2 Removing the front cover
Remove the front cover when making the following replacements:
– Replacing the operating panel
– Replacing the DVD/DVD-RW drive
– Replacing the intrusion switches
ÊPush the drive cover up as far as possible.
ÊRemove the hard disk cover.

18 Service Supplement TX150 S5
Preparation Replacement routines
ÊDisengage the three tabs on the left side one after the other and rotate the
front cover outward about 2 cm.
ÊPush down the drive cover and then press the upper hook on the right side
inward.
ÊPush the drive cover upward.
ÊPress the two hooks on the right side inward and pull out the front cover
frontward.
4.1.2 Rack model
IYou will find a detailed description of “Opening the server“ and
“Removing the rack front cover“ in the Options Guide TX150 S5.
ÊTerminate all applications and shut down the server correctly.
ÊIf your operating system has not switched off the server, press the on/off
button for at least four seconds (“Power override“ function).
ÊPull all power connectors out of the power outlets.
4.1.2.1 Opening the server
ÊLoosen the four knurled screws and pull the server as far as possible out of
the rack.
Depending on how accessible the server is in the rack cabinet, it can make
sense to remove it from the cabinet. You will find a detailed description in the
Options Guide or the Operating Manual.
ÊLoosen the two screws at the server’s rear side.
ÊPush back the top cover approxiate 2 cm.
ÊRemove the top cover.

TX150 S5 Service Supplement 19
Replacement routines Replacing the operating panel module
4.1.2.2 Removing the rack front cover
Remove the rack front cover when making the following replacements:
– Replacing the operating panel
– Replacing the DVD/DVD-RW drive
– Replacing the intrusion switches
ÊRemove two screws on either side.
ÊRemove the rack front cover to the front.
ÊDisengage the three tabs on the top side one after the other and pull out the
plastic front cover frontward about 2 cm.
ÊPress the three hooks on the bottom side downward and pull out the plastic
front cover frontward.
4.2 Replacing the operating panel module
ÊOpen the server and remove the front cover / rack front cover as described
in the section “Preparation” on page 17.
Figure 2: Removing the operating panel module
ÊPress the two metal tongues of the EasyClick rails inward (1) until the locking
mechanism is released.
ÊPull the operating panel module forward out of its mounting location (2) until
you can remove the ribbon cable and the USB cable from the operating
panel board. Remove the two cables.
1
1

20 Service Supplement TX150 S5
Replacing the DVD/DVD-RW drive Replacement routines
ÊPull the operating panel module out of its bay as far as it is possible to get
access to the cable tie.
ÊThread the two cables through the cable tie.
ÊTake the operating panel module out of its bay.
ÊPush the new operating panel module into its bay as far as it is possible to
have access to the cable tie.
ÊThread the two cables through the cable tie.
ÊPush the operating panel module into its bay as far as it is possible to plug
the cables.
ÊConnect the ribbon cable and the USB cable to the operating panel board
(see the board layout on page 43).
ÊPush the operating panel module into the housing until it engages.
ÊClose the server and connect all power plugs (for a detailed description see
the Options Guide).
4.3 Replacing the DVD/DVD-RW drive
In the basic configuration the top 5.25-inch bay of the accessible drives is
occupied with a DVD/DVD-RW drive.
ÊOpen the server and remove the front cover / rack front cover as described
in the section “Preparation” on page 17.
ÊRemove the power and the data cable at the rear side of the DVD/DVD-RW
drive.