Fujitsu PRIMERGY TX150 S6 User manual

PRIMERGY TX150 S6 Server
Options Guide
Edition June 2009

Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
[e-mail].
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
Copyright © 2009Fujitsu Technology Solutions GmbH.
All rights reserved.
Delivery subject to availability. The right to technical modification is reserved.
All hardware and software names used are trade names and/or trademarks of their respective
manufacturers.

TX150 S6 Options Guide
Contents
1 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.1 Concept and target groups . . . . . . . . . . . . . . . . . . . 7
1.2 Documentation overview . . . . . . . . . . . . . . . . . . . . 7
1.3 Expansions and conversions . . . . . . . . . . . . . . . . . . 9
1.4 Notational conventions . . . . . . . . . . . . . . . . . . . . 11
2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . 15
4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.1 Floorstand model . . . . . . . . . . . . . . . . . . . . . . . . 21
4.1.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 21
4.1.2 Removing the front cover . . . . . . . . . . . . . . . . . . . . 22
4.1.3 Removing the hard disk cover . . . . . . . . . . . . . . . . . . 24
4.2 Rack model . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.2.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 25
4.2.2 Removing the rack front cover . . . . . . . . . . . . . . . . . . 28
5 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.1 Equipping rules . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.2 Expanding/replacing the main memory . . . . . . . . . . . . 30
6 Accessible drives . . . . . . . . . . . . . . . . . . . . . . . 33
6.1 Installing an accessible 5.25-inch drive . . . . . . . . . . . . 34
6.2 Installing a 3.5-inch floppy disk drive . . . . . . . . . . . . . 37
6.3 Installing a hard disks extension box . . . . . . . . . . . . . 39

Options Guide TX150 S6
Contents
6.4 Installing the multibay . . . . . . . . . . . . . . . . . . . . . . 46
7 ServerView Local Service Panel . . . . . . . . . . . . . . . . 49
7.1 Installing a LSP . . . . . . . . . . . . . . . . . . . . . . . . . 49
8 Expansion cards in the PCI slots . . . . . . . . . . . . . . . . 57
8.1 Installing an expansion card . . . . . . . . . . . . . . . . . . 58
8.2 PCI slot assembly . . . . . . . . . . . . . . . . . . . . . . . . 60
8.3 Installing a BBU . . . . . . . . . . . . . . . . . . . . . . . . . 61
9 SATA SW RAID . . . . . . . . . . . . . . . . . . . . . . . . . . 63
9.1 Inserting the RAID key . . . . . . . . . . . . . . . . . . . . . 63
10 External interfaces . . . . . . . . . . . . . . . . . . . . . . . 65
10.1 Installing the COM2 interface . . . . . . . . . . . . . . . . . . 65
10.2 Installing a parallel interface . . . . . . . . . . . . . . . . . . 66
11 Conversion standard PS to hot-plug PS . . . . . . . . . . . . 69
12 Conversion from a floorstand model to a rack model . . . . . 79
13 Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
13.1 Floorstand model . . . . . . . . . . . . . . . . . . . . . . . . 85
13.1.1 Attaching the hard disk cover . . . . . . . . . . . . . . . . . . . 85
13.1.2 Attaching the front cover . . . . . . . . . . . . . . . . . . . . . 86
13.1.3 Closing the server . . . . . . . . . . . . . . . . . . . . . . . . . 87
13.2 Rack model . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
13.2.1 Attaching the rack front cover . . . . . . . . . . . . . . . . . . . 88
13.2.2 Closing the server . . . . . . . . . . . . . . . . . . . . . . . . . 89

TX150 S6 Options Guide
Contents
14 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
14.1 Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

TX150 S6 Options Guide 7
1 Preface
The PRIMERGY TX150 S6 server is an Intel-based server for small and mid-
size networks. The server is suitable for use as a file server and also as an appli-
cation, information or Internet server. It is available as a floorstand or rack
model. The floorstand model can be converted to a rack model using an optional
conversion kit.
1.1 Concept and target groups
This Options Guide shows you how to extend and upgrade your server.
VCAUTION!
The activities described in this manual may only be performed by
technical specialists.
IThe installation and removal of the hot-plug components is described in
the Operating Manual supplied with the server.
1.2 Documentation overview
More information on your PRIMERGY TX150 S6 can be found in the following
documents:
– “Quick Start Hardware - PRIMERGY TX150 S6” leaflet (only included as a
printed copy)
– “Quick Start Software - Quick Installation Guide” leaflet (only included as a
printed copy)
– “Safety notes and other important information” manual
– “Warranty” manual
– “Customer Self Service (CSS)” manual
– “Ergonomics” manual
– “Returning used devices” manual
– “Helpdesk” leaflet
– Technical manual for the system board D2559

8 Options Guide TX150 S6
Documentation overview Preface
– “PRIMERGY TX150 S6 Server Operating Manual”
– “PRIMERGY TX150 S6 Server Options Guide”
– “BIOS Setup V4.06 / FirstBIOS Desktop Pro V5.0 /TrustedCoreTM V6.0”
manual
– “SAS/SATA Controller MegaRAID 1064 / 1068 / 1078 Installation Guide”
– “LSI SATA Software RAID User’s Guide”
– “LSI Logic MegaRAID SAS Software User’s Guide”
– “LSI Logic MegaRAID SAS Device Driver Installation” manual
– “Integrated RAID for SAS User’s Guide”
– “Embedded SATA Software RAID for ICH7R User’s Guide”
– “ServerView RAID User's Guide”
– “Integrated Mirroring User’s Guide”
IPRIMERGY manuals are available in PDF format on the ServerBooks
DVD. The ServerBooks DVD is part of the ServerStart Suite supplied with
every server.
The PDF files of the manuals can also be downloaded free of charge
from the Internet. The overview page showing the online documentation
available on the Internet can be found using the URL:
http://manuals.ts.fujitsu.com. The PRIMERGY server documentation
can be accessed using the Industry standard servers navigation option.
Further sources of information:
– Manual for the monitor
– Documentation for boards and drives
– Documentation for your operating system
– Information files on your operating system

TX150 S6 Options Guide 9
Preface Expansions and conversions
1.3 Expansions and conversions
Main memory expansion
The system board supports up to 16 Gbyte main memory. 4 slots (2 memory
banks with 2 slots each) are provided for the main memory. Each memory bank
can be populated with 512 Mbyte, 1 Gbyte, 2 Gbyte or 4 Gbyte unbuffered
DDR2 memory modules.
Accessible drives
Three 5.25-inch bays are available for accessible drives. In these bays you can
install a DVD/DVD-RW drives, magnetic tape drives, a multibay (slimline DVD
and FDD/ServerView Local Service Panel) or a hard disks extension box (only
SAS base units). Below the 5.25-inch bays for accessible drives you will find
also a bay for a 3.5-inch floppy disk drive.
Hard disks extension box
In the SAS base units two 5.25-inch bays for accessible drives can be used to
install a hard disks extension box.
Two variants of the hard disks extension box are available:
– Variant 1:
one bay for a ServerView Local Service Panel, one bay for a slimline DVD
drive and two bays for 3.5“ hard disks
– Variant 2 (special release required):
eight bays for 2.5“ hard disks
ServerView Local Service Panel
The system board supports the CSS (Customer Self Service) functionality
(description see the operating manual). You can install a ServerView Local
Service Panel for an easier identification of the defective components.

10 Options Guide TX150 S6
Expansions and conversions Preface
Additional expansion cards in the PCI slots
The system board offers six PCI slots:
– 3 x PCI (32 Bit / 33 MHz)
– 2 x PCI Express x8
– 1 x PCI Express x4
SATA Software RAID
Only possible in SATA base units: the SATA SW RAID 5 functionality will be
activated by installing a license key (RAID key).
COM2 interface
As an option, a second serial interface (COM2) can be provided.
Parallel interface for printers
As an option, a parallel interface can be provided for printers.
Conversion standard power supply to hot-plug power supply
The standard power supply can be replaced by a hot-plug power supply. The
hot-plug power supply consists of two power supply modules. The conversion
kit contains only one power supply module, you have to order the second power
supply separately.
If one power supply module fails, the other power supply module guarantees the
unrestricted operation and the defective power supply module can be replaced
be replaced while the system is operating (hot-plug).
Conversion from a floorstand model to a rack model
The floorstand model can be optionally converted to allow the server to be
installed into any typical rack systems.

TX150 S6 Options Guide 11
Preface Notational conventions
1.4 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands or menu items.
“Quotation marks” indicate names of chapters and terms that are being
emphasized.
Êdescribes activities that must be performed in the order
shown.
VCAUTION! pay particular attention to texts marked with this symbol.
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips.

TX150 S6 Options Guide 13
2Procedure
VCAUTION!
●The actions described in this manual should only be performed by
technical specialists.
●Repairs to the device that do not relate to CSS failures must only be
carried out by service personnel. Please note that unauthorized inter-
ference with the system will void the warranty and exempt the
manufacturer from all liability.
●Any failure to observe the guidelines in this manual, and any improper
repairs could expose the user to risks (electric shock, energy
hazards, fire hazards) or damage the equipment.
ÊFirst of all, carefully read the safety instructions in the chapter “Safety
instructions” on page 15 et seq..
ÊMake sure that all necessary manuals (see the section “Documentation
overview” on page 7) are available; print the PDF files if required. Most
importantly, you will need the operating manual for the server and the
technical manual for the system board.
ÊShut the server down correctly, switch it off, disconnect the power plugs and
open the server as described in the chapter “Preparation” on page 21 et
seq..
ÊCarry out the expansion or upgrade of your server as described in the
pertinent chapter.
IInstallation and removal of the hot-plug components are described in
the operating manual.
ÊClose the server, connect it to the power outlet, and switch it on as described
in the chapter “Completion” on page 85 et seq..
ÊStart the operating system and make the appropriate configuration if
necessary (see the operating manual).

TX150 S6 Options Guide 15
3 Safety instructions
IThe following safety instructions are also provided in the manual “Safety
notes and other important information”.
This device meets the relevant safety regulations for IT equipment. If you have
any questions about whether you can install the server in the intended
environment, please contact your sales outlet or our customer service team.
VCAUTION!
●The actions described in this manual should only be performed by
technical specialists.
●Repairs to the device that do not relate to CSS failures must only be
carried out by service personnel. Please note that unauthorized inter-
ference with the system will void the warranty and exempt the
manufacturer from all liability.
●Any failure to observe the guidelines in this manual, and any improper
repairs could expose the user to risks (electric shock, energy
hazards, fire hazards) or damage the equipment.

16 Options Guide TX150 S6
Safety instructions
Before starting up
VCAUTION!
●During installation and before operating the device, observe the
instructions on environmental conditions for your device.
●If the device is brought in from a cold environment, condensation may
form both inside and on the outside of the device.
Wait until the device has acclimatized to room temperature and is
absolutely dry before starting it up. Material damage may be caused
to the device if this requirement is not observed.
●Transport the device only in the original packaging or in packaging
that protects it from knocks and jolts.
Installation and operation
VCAUTION!
●This unit should not be operated in ambient temperatures above
35 °C.
●If the unit is integrated into an installation that draws power from an
industrial power supply network with an IEC309 connector, the power
supply's fuse protection must comply with the requirements for non-
industrial power supply networks for type A connectors.
●The unit automatically adjusts itself to a mains voltage in a range of
100 V -240 V. Ensure that the local mains voltage lies within these
limits.
●This device must only be connected to properly grounded shock-
proof sockets or insulated sockets of the rack's internal power supply
with tested and approved power cables.
●Ensure that the device is connected to a grounded shockproof socket
close to the device.

TX150 S6 Options Guide 17
Safety instructions
VCAUTION!
●Ensure that the power sockets on the device and the grounded shock-
proof sockets are freely accessible.
●The On/Off button or the main power switch (if present) does not
isolate the device from the mains power supply. To disconnect it
completely from the mains power supply, unplug all network power
plugs from the grounded shockproof sockets.
●Always connect the server and the attached peripherals to the same
power circuit. Otherwise you run the risk of losing data if, for example,
the server is still running but a peripheral device (e.g. memory
subsystem) fails during a power outage.
●Data cables must be adequately shielded.
●The EN 50173 and EN 50174-1/2 standards apply for LAN cabling.
The minimum requirement is the use of a category 5 screened LAN
cable for 10/100 Mbps Ethernet, or a category 5e cable for Gigabit
Ethernet. The requirements from the ISO/IEC 11801 specification
must also be met.
●Route the cables in such a way that they do not create a potential
hazard (make sure no-one can trip over them) and that they cannot
be damaged. When connecting the server, refer to the relevant
instructions in this manual.
●Never connect or disconnect data transmission lines during a storm
(risk of lightning strike).
●Make sure that no objects (e.g. jewelry, paperclips etc.) or liquids can
get inside the server (risk of electric shock, short circuit).
●In emergencies (e.g. damaged casing, controls or cables, penetration
of liquids or foreign bodies), switch off the server immediately, remove
all power plugs and contact your sales outlet or customer service
team.

18 Options Guide TX150 S6
Safety instructions
VCAUTION!
●Proper operation of the system (in accordance with
IEC 60950-1/EN 60950-1) is only ensured if the casing is completely
assembled and the rear covers for the installation slots have been
fitted (electric shock, cooling, fire protection, interference
suppression).
●Only install system expansions that satisfy the requirements and
rules governing safety and electromagnetic compatibility and those
relating to telecommunication terminals. If you install other expan-
sions, they may damage the system or violate the safety regulations.
Information on which system expansions are approved for installation
can be obtained from our customer service center or your sales
outlet.
●The components marked with a warning notice (e.g. lightning symbol)
may only be opened, removed or exchanged by authorized, qualified
personnel. Exception: hot-plug power supply units/CCS components
can be replaced.
●The warranty is void if the server is damaged during installation or
replacement of system expansions.
●Only set screen resolutions and refresh rates that are specified in the
operating manual for the monitor. Otherwise, you may damage your
monitor. If you are in any doubt, contact your sales outlet or customer
service center.
Batteries
VCAUTION!
●Incorrect replacement of batteries may result in a risk of explosion.
The batteries may only be replaced with identical batteries or with a
type recommended by the manufacturer (see the technical manual for
the system board).
●Replace the lithium-battery on the system board in accordance with
the instructions in the technical manual for the system board.

TX150 S6 Options Guide 19
Safety instructions
Working with CDs/DVDs and CD/DVD drives
When working with devices with CD/DVD drives, these instructions must be
followed.
VCAUTION!
●Only use CDs/DVDs that are in perfect condition in your server's
CD/DVD drive, in order to prevent data loss, equipment damage and
injury.
●Check each CD/DVD for damage, cracks, breakages etc. before
inserting it in the drive.
Note that any additional labels applied may change the mechanical
properties of a CD/DVD and cause imbalance.
Damaged and imbalanced CDs/DVDs can break at high drive speeds
(data loss).
Under certain circumstances, sharp CD/DVD fragments can pierce
the cover of the CD/DVD drive (equipment damage) and can fly out
of the device (danger of injury, particularly to uncovered body parts
such as the face or neck).
IYou can prevent mechanical damage and damage to the CD/DVD drive,
as well as premature CD/DVD wear, by observing the following sugges-
tions:
– Only insert CDs/DVDs in the drive when needed and remove them
after use.
– Store the CDs/DVDs in suitable sleeves.
– Protect the CDs/DVDs from exposure to heat and direct sunlight.
Laser information
The CD/DVD drive complies with IEC 60825-1 laser class 1.
VCAUTION!
The CD/DVD drive contains a light-emitting diode (LED), which under
certain circumstances produces a laser beam stronger than laser
class 1. Looking directly at this beam is dangerous.
Never remove parts of the CD/DVD drive casing!

20 Options Guide TX150 S6
Safety instructions
Modules with electrostatic-sensitive devices
Modules with electrostatic-sensitive devices are identified by the following
sticker:
Figure 1: ESD label
When you handle components fitted with ESDs, you must always observe the
following points:
●Switch off the system and remove the power plugs from the power outlets
before installing or removing components with ESDs.
●You must always discharge static build-up (e.g. by touching a grounded
object) before working with such components.
●Any devices or tools that are used must be free of electrostatic charge.
●Wear a suitable grounding cable that connects you to the external chassis of
the system unit.
●Always hold components with ESDs at the edges or at the points marked
green (touch points).
●Do not touch any connectors or conduction paths on an ESD.
●Place all the components on a pad which is free of electrostatic charge.
IFor a detailed description of how to handle ESD components, see the
relevant European or international standards (EN 61340-5-1,
ANSI/ESD S20.20).