Fujitsu PRIMERGY TX200 S2 User manual

PRIMERGY
PRIMERGY TX200 S2
Server System
Options Guide
Susanne Däschlein
Fujitsu Siemens Computers GmbH München
81730 München
e-mail: email: [email protected]
Tel.: [phone]
Fax: (++49) 700 / 372 00000
U41593-J-Z156-2-76
Sprachen: En
Edition February 2006

Comments Suggestions Corrections
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Fax forms for sending us your comments are included in
the back of the manual.
There you will also find the addresses of the relevant
User Documentation Department.
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademar s
Copyright © 2006 Fujitsu Siemens Computers GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.

U41593-J-Z156-2-76 Options Guide
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Overview of the documentation . . . . . . . . . . . . . . . . . . 5
1.2 Extensions and conversions . . . . . . . . . . . . . . . . . . . . 6
1.3 Notational conventions . . . . . . . . . . . . . . . . . . . . . . 9
2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3 Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1 Floorstand model . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 19
4.1.2 Removing the front cover . . . . . . . . . . . . . . . . . . . . 20
4.2 Rack model . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.2.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 23
4.2.2 Removing the rack front cover . . . . . . . . . . . . . . . . . . 26
5 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.1 Equipping rules . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.2 Extending/replacing the main memory . . . . . . . . . . . . . 28
6 Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.1 Installing a second processor . . . . . . . . . . . . . . . . . . 31
6.2 Replacing the processor . . . . . . . . . . . . . . . . . . . . 40
6.3 Replacing the heat sink . . . . . . . . . . . . . . . . . . . . . 43
7 Accessible drives . . . . . . . . . . . . . . . . . . . . . . . 45
7.1 Installing a slim line CD/DVD-ROM drive . . . . . . . . . . . . 45
7.2 Installing an accessible 5.25-inch drive . . . . . . . . . . . . . 48
7.3 Installing the hard disks extension box . . . . . . . . . . . . . 53
8 Controller in the PCI slots . . . . . . . . . . . . . . . . . . . 57
8.1 Installing a controller (PCI slots 1-4) . . . . . . . . . . . . . . 58
8.2 Installing a controller (PCI slot 5) . . . . . . . . . . . . . . . . 60
8.3 PCI slot assembling . . . . . . . . . . . . . . . . . . . . . . . 64
9 RemoteView components . . . . . . . . . . . . . . . . . . . 67
9.1 Installing the chipDISK . . . . . . . . . . . . . . . . . . . . . 67
9.2 RemoteView Service Board S2 LP . . . . . . . . . . . . . . . 68
10 External SCSI interface . . . . . . . . . . . . . . . . . . . . 71
10.1 Installing the external SCSI interface . . . . . . . . . . . . . . 71

Options Guide U41593-J-Z156-2-76
Contents
11 Parallel interface for printers . . . . . . . . . . . . . . . . . 73
11.1 Installing a parallel interface . . . . . . . . . . . . . . . . . . . 73
12 Upgrading to redundant system fans . . . . . . . . . . . . 77
13 Conversion standard PS to hot-plug PS . . . . . . . . . . . 83
14 Converting from the floorstand model to the rack model . . 93
15 Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
15.1 Floorstand model . . . . . . . . . . . . . . . . . . . . . . . . 97
15.1.1 Attaching the front cover . . . . . . . . . . . . . . . . . . . . 97
15.1.2 Closing the server . . . . . . . . . . . . . . . . . . . . . . . . 99
15.2 Rack model . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
15.2.1 Attaching the rack front cover . . . . . . . . . . . . . . . . . . 101
15.2.2 Closing the server . . . . . . . . . . . . . . . . . . . . . . . . 102
16 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
16.1 Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
16.2 SCSI configurations . . . . . . . . . . . . . . . . . . . . . . . 111
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

U41593-J-Z156-2-76 Options Guide 5
1Introduction
The PRIMERGY TX200 S2 Server is an Intel-based server for medium-sized
networks and large companies. The server is suitable for use as a file server as
well as an application, information, or Internet server. It is available as a floor-
stand or rack model. The floorstand model can be converted to a rack model
using an optional conversion kit.
1.1 Overview of the documentation
IPRIMERGY manuals are available in PDF format on the ServerBooks CD
which is supplied in the ServerView Suite package for every server system.
These PDF files can also be downloaded free of charge from the
Internet: at http://manuals.fujitsu-siemens.com you will find an overview
page with the online documentation available on the Internet. You can go
to the PRIMERGY Server documentation by clicking on industry standard
servers.
Concept and target groups
This Options Guide shows you how you can expand and upgrade the server.
IThe Operating Manual for the server describes how you install/remove
the hot-plug components.
The activities described in this manual may only be performed by technical
specialists.
Additional documentation about the server
The PRIMERGY TX200 S2 documentation comprises the following additional
manuals:
– The “Safety” manual (printed copy always supplied with the server, and
available as a PDF file on the ServerBooks CD supplied)
– The “Guarantee” manual (printed copy always supplied with the server, and
available as a PDF file on the ServerBooks CD supplied)
– The “Returning used devices” manual (PDF file available on the ServerBooks
CD)

6 Options Guide U41593-J-Z156-2-76
Extensions and conversions Introduction
– The Operating Manual for PRIMERGY TX200 S2 (PDF available on the
ServerBooks CD supplied)
– The Technical Manual for the system board D1919 (PDF available on the
ServerBooks CD supplied)
– The “BIOS Setup” manual (PDF available on the ServerBooks CD supplied)
– The “PRIMERGY ServerView Suite - ServerStart” manual (printed copy
always supplied with the server, and available as PDF file on the ServerBooks
CD supplied)
– The “Global Array Manager Client Software User’s Guide” (PDF available on
the ServerBooks CD supplied)
– The “Integrated Mirroring User’s Guide” (PDF available on the ServerBooks
CD supplied)
IYou can order a supplementary ServerBooks CD by sending an e-mail to
the following address, quoting your server data:
Reklamat-PC-LO[email protected]
Further sources of information:
– Technical Manual on the relevant rack
– Manual on the monitor
– Manual on ServerView Server Management
– Manual on the RemoteView Remote Test and Diagnostics System
– Documentation on boards and drives
– Documentation on your operating system
– Information files on your operating system
(see also “Related publications” on page 121)
1.2 Extensions and conversions
Second processor
The system board can be upgraded with a second processor. Only processors
of the same type may be used on the system board. The second processor must
have at least the same clock frequency as the first processor.

U41593-J-Z156-2-76 Options Guide 7
Introduction Extensions and conversions
Extension of the main memory
The six slots for the main memory are suitable for PC2-3200 DDR DIMM
memory modules. The organization in three memory banks, 0 to 2, permits
rapid memory access with two-way interleaving.
Memory modules must always be incorporated in pairs. A memory bank must
always be equipped fully with the same type of memory modules.
Additional accessible drives
Two free 5.25-inch bays are available for accessible drives.
The third 5.25-inch bay offers a 5.25-inch slim line and a 5.25-inch bay. The
5.25-inch bay is occupied by a 3.5-inch x 1-inch floppy disk drive.
Hard disks extension box
The two free 5.25-inch bays for accessible drives can be used to integrate a
hard disks extension box.
The hard disks extension box enables up to three additional HDD modules to be
integrated. Each HDD module can accommodate a SCSI hard disk drive with
an SCA (Single Connector Attachment) interface and a height of at most 1 inch.
The connection to the SCSI backplane is made without cables via the SCA
interface. This makes it simple to plug in or pull out the HDD modules. If the
server has a RAID controller and the corresponding RAID configuration,
defective HDD modules can also be replaced while the system is operating.
Additional controllers in the PCI slots
The system board offers five PCI slots. The bus frequency of PCI slot 5 is
33 MHz, of the PCI slots 3 and 4 100 MHz/133 MHz and of the PCI slots 1
and 2 66 MHz.
The hardware of the system board optimizes the speed of the PCI bus (IOOP™)
for PCI slots 3 and 4, depending on how the slots are equipped. If only one of
this two slots is occupied, the PCI bus speed is 133 MHz. For all other
equipment variants the PCI bus speed is 100 MHz.
The PCI slot 1(blue socket) is prepared for Zero Channel RAID (ZCR).

8 Options Guide U41593-J-Z156-2-76
Extensions and conversions Introduction
RemoteView
RemoteView provides you with a comprehensive test and diagnostics package.
The test and diagnostics software is stored on a chipDISK. The chipDISK is a
memory component with an IDE interface. In the event of a fault the test and
diagnostics software is automatically loaded from the chipDISK and executed.
RemoteView Service Board S2 LP
The RemoteView Service Board S2 LP (RSB S2 LP) is a PCI board with a
completely independent system, i.e. it has its own operating system with Web
server and SNMP agents and can optionally be equipped with an external
power supply. The RSB S2 LP is inserted into PCI slot 5 and connected to the
system board via a power and a data cable. The RSB S2 LP permits remote
diagnosis for system analysis, remote system configuration and remote restart
even in the event of operating system failure or hardware faults. It has its own
LAN connection and its own COM port. All the functions of the RSB S2 LP are
thus available either via a LAN or modem.
External SCSI interface
If the internal hard disks are connected via a PCI RAID controller, one channel
of the on-board controller can also be made available for connecting peripheral
cabinets via an external SCSI interface.
Parallel interface for printers
As an option, a parallel interface can be provided for printers.
Upgrading to redundant system fans
The two system fans can be upgraded to four system fans. If four system fans
are installed, the fans are operating in a redundant configuration. A defective
system fan can be replaced during the next service.
Conversion standard power supply to hot-plug power supply
The standard power supply can be replaced by a hot-plug power supply. The
hot-plug power supply consists of two power supply modules.
If one power supply module fails, the other power supply module guarantees the
unrestricted operation and the defective power supply module can be replaced
be replaced while the system is operating (hot-plug).

U41593-J-Z156-2-76 Options Guide 9
Introduction Notational conventions
Conversion of the floorstand model to a rack model
The floorstand model can optionally be converted so that the server can be
integrated into the common rack systems.
1.3 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands, menu items or software programs.
„Quotation marks“ indicate names of chapters and terms that are being
emphasized.
Êdescribes activities that must be performed in the order
shown.
VCAUTION! pay particular attention to texts marked with this symbol.
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips.
Table 1: Notational conventions

U41593-J-Z156-2-76 Options Guide 11
2Procedure
VCAUTION!
The actions described in these instructions should only be performed by
technical specialists. Equipment repairs should only be performed by
authorized, qualified staff. Any unauthorized opening and improper
repairs could expose the user to risks (electric shock, energy hazards,
fire hazards) and could also damage the equipment. Please note that
any unauthorized opening of the device will result in the invalidation of
the warranty and exclusion from all liability.
ÊFirst of all please familiarize yourself with the safety instructions in the
section chapter “Safety notes” on page 13ff.
ÊEnsure that all required manuals (see “Additional documentation about the
server” on page 5) are available, printing out the PDF files if necessary. You
will definitely need the Operating Manual for the server and the Technical
Manual for the system board.
ÊShut down the server correctly, switch it off, pull out the power plug, and
open the server as described in the chapter “Preparation” on page 19ff.
ÊExtend or upgrade your server as described in the relevant chapter.
IThe Operating Manual for the server describes how you
install/remove the hot-plug components.
IProcedures which are identical for the floorstand and rack models are
only described for the floorstand model.
ÊClose the server, connect it to the power outlet, and switch it on as described
in the chapter “Completion” on page 97ff.
ÊStart the operating system and, if necessary, configure it as required (see
the Operating Manual).

U41593-J-Z156-2-76 Options Guide 13
3 Safety notes
IThe following safety notes are also provided in the “Safety” manual.
This device complies with the relevant safety regulations for data processing
equipment.
If you have any questions about where you can set up the device, contact your
sales outlet or our customer service team.
VCAUTION!
The actions described in these instructions should only be performed by
technical specialists. Equipment repairs should only be performed by
authorized, qualified staff. Any unauthorized openings and improper
repairs could expose the user to risks (electric shock, energy hazards,
fire hazards) and could also damage the equipment. Please note that
any unauthorized openings of the device will result in the invalidation of
the warranty and exclusion from all liability.
Before operating the device
VCAUTION!
●During installation and before operating the device, observe the
instructions on environmental conditions for your device.
●If the device is brought in from a cold environment, condensation may
form both inside and on the outside of the machine.
Wait until the device has acclimatized to room temperature and is
absolutely dry before starting it up. Material damage may be caused
to the device if this requirement is not observed.
●Transport the device only in the original packaging or in packaging
that protects it from knocks and jolts.

14 Options Guide U41593-J-Z156-2-76
Safety notes
Installation and operation
VCAUTION!
●If the rack model is integrated in an installation that receives power
from an industrial (public) power supply network with the IEC309
connector, the (public) power supply protection must comply with the
requirements for the non-industrial (public) power supply networks for
the type A connector.
●The server automatically sets itself to a voltage in the range of
100 V to 240 V. Make sure that your local voltage is within this range.
●This device has a specially approved power cable and must only be
connected to a grounded insulated socket.
●Ensure that the power socket on the device or the grounded wall
outlet is freely accessible.
●The ON/OFF button does not disconnect the device from the mains
voltage. To disconnect the line voltage completely, switch OFF the
mains power switch (if available on the standard power supply unit)
and remove the power plug(s) from the grounded insulated socket(s).
●Always connect the device and the attached peripherals to the same
power circuit. Otherwise you run the risk of losing data if, for example,
the central processing unit is still running but the peripheral device
(e.g. storage subsystem) has failed during a power outage.
●Data cables to peripheral devices must be adequately shielded.
●To the LAN wiring the requirements apply in accordance with the
standards EN 50173 and EN 50174-1/2. As minimum requirement
the use of a protected LAN line of category 5 for 10/100 MBps
Ethernet, and/or of category 5e for Gigabit Ethernet is considered.
The requirements of the specification ISO/IEC 11801 are to be
considered.
●Route the cables in such a way that they do not form a potential
hazard (make sure no-one can trip over them) and that they cannot
be damaged. When connecting up a device, refer to the relevant
notes in this manual.
●Never connect or disconnect data transmission lines during a storm
(lightning hazard).

U41593-J-Z156-2-76 Options Guide 15
Safety notes
VCAUTION!
●In emergencies (e.g. damaged casing, controls or cables, penetration
of liquids or foreign matter), switch off the device immediately, remove
the power plug and contact your sales outlet or customer service
team.
●Proper operation of the device (in accordance with IEC 60950/
EN 60950) is only ensured if the casing is completely assembled and
the rear covers for the installation openings have been put in place
(electric shock, cooling, fire protection, interference suppression).
●Only install system expansions that satisfy the requirements and
rules governing safety and electromagnetic compatibility and relating
to telecommunications terminal equipment. If you install other expan-
sions, you may damage the system or violate the safety regulations
and regulations governing RFI suppression. Information on which
system expansions are suitable can be obtained from the customer
service centre or your sales outlet.
●The components or parts marked with a warning label (e.g. lightning
symbol) may only be opened, removed or exchanged by authorized,
qualified personnel. The hot-plug power supply units are exceptions
to this rule.
●The warranty expires if the device is damaged during the installation
or replacement of system expansions.
●You may only set those resolutions and refresh rates specified in the
„Technical data“ section of the monitor description. Otherwise, you
may damage your monitor. If you are in any doubt, contact your sales
outlet or customer service centre.

16 Options Guide U41593-J-Z156-2-76
Safety notes
Batteries
VCAUTION!
●Incorrect replacement of batteries may lead to a risk of explosion. The
batteries may only be replaced with identical batteries or with a type
recommended by the manufacturer (see the technical manual for the
system board under “Related publications” on page 121).
●Replace the lithium battery on the system board in accordance with
the instructions in the technical manual for the system board (see
“Related publications” on page 121).
Notes on handling CDs and CD-/DVD-ROM drives
VCAUTION!
●Use only CDs in proper condition in the CD-/DVD-ROM drive of your
server to prevent data loss, damage to the device and injuries.
●Therefore, check each CD for damage, cracks, breakage etc. before
inserting it in the drive.
Please note that any additional labels applied may change the
mechanical properties of a CD and cause imbalance.
Damaged and imbalanced CDs can break at high drive speeds (data
loss).
Under certain conditions sharp-edged pieces of broken CDs can
penetrate the cover of the drive (damage to the device) and be thrown
out of the device (danger of injury, particularly on uncovered body
parts such as the face or neck).
IYou protect the CD-/DVD-ROM drive and prevent mechanical damage,
as well as premature wearing of the CDs, by observing the following
suggestions:
– Only insert the CDs in the drive when needed and remove them after
use.
– Store the CDs in suitable sleeves.
– Protect the CDs from exposure to heat and direct sunlight.

U41593-J-Z156-2-76 Options Guide 17
Safety notes
Note about the laser
The CD-/DVD-ROM drive is classified for laser class 1according to IEC 60825-
1.
VCAUTION!
The CD-/DVD-ROM drive contains a laser diode (LED). Sometimes the
LED produces a stronger laser beam than laser class 1. Direct view into
this laser beam is dangerous.
Never remove parts of the CD-/DVD-ROM drive assembly!
Modules with electrostatic-sensitive components:
Systems and components that might be damaged by electrostatic discharge
(ESD) are marked with the following label:
Figure 1: ESD label
When you handle components fitted with ESDs, you must observe the following
points under all circumstances:
●Remove the power plug from the power socket before inserting or removing
components containing ESDs.
●You must always discharge yourself of static charges (e.g. by touching a
grounded object) before working.
●The equipment and tools you use must be free of static charges.
●Only touch the components at the positions highlighted in green (touch
points).
●Do not touch any exposed pins or conductors on a component.
●Use a grounding cable designed for this purpose to connect yourself to the
system unit as you install components.

18 Options Guide U41593-J-Z156-2-76
Safety notes
●Place all components on a static-safe base.
IYou will find a detailed description for handling ESD components in the
relevant European or international standards (DIN EN 61340-5-1,
ANSI/ESD S20.20).

U41593-J-Z156-2-76 Options Guide 19
4 Preparation
VCAUTION!
Observe the safety instructions in the chapter “Safety notes” on
page 13ff.
4.1 Floorstand model
4.1.1 Opening the server
ÊTerminate all applications and shut down the server correctly.
ÊIf your operating system has not switched off the sever, press the on/off
switch.
ÊPull all power connectors out of the power outlets.
ÊIf required, remove the lock on the side cover.
Figure 2: Loosening the knurled screw
ÊLoosen the green knurled screw (1).
1

20 Options Guide U41593-J-Z156-2-76
Floorstand model Preparation
Figure 3: Removing the left-hand side cover
ÊPush back the left-hand side cover approxiate 10 cm (1).
ÊRemove the side cover (2).
4.1.2 Removing the front cover
Remove the front cover when making the following extensions and upgrades:
– Installing further accessible drives
– Upgrading the floorstand model to a rack model
2
1