Fujitsu PRIMERGY TX600 S2 User manual

PRIMERGY
PRIMERGY TX600 S2
Server System
Options Guide
Joachim Pichol
Fujitsu Siemens Computers GmbH Paderborn
33094 Paderborn
e-mail: email: [email protected]
Tel.: [phone]
Fax: (++49) 700 / 372 00001
U41612-J-Z156-2-76
Sprachen: En
Edition November 2005

Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Fax forms for sending us your comments are included in
the back of the manual.
There you will also find the addresses of the relevant
User Documentation Department.
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
© cognitas. Gesellschft für Technik-Dokumentation mbH 2005 Pfad: D:\Aktuelles_Projekt\PRIMERGY\RX_TX600S2-Update\OG-TX\TX600S2_og.us.pdf\TX600S2_og_us.vor
Copyright © 2005 Fujitsu Siemens Computers GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.

U41612-J-Z156-2-76 Options Guide
Contents
1 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Documentation overview . . . . . . . . . . . . . . . . . . . . . 1
1.2 Extensions and conversions . . . . . . . . . . . . . . . . . . . . 3
1.3 Notational conventions . . . . . . . . . . . . . . . . . . . . . . 5
2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Environmental Protection . . . . . . . . . . . . . . . . . . . . 15
4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 19
4.1.1 Opening the rack model . . . . . . . . . . . . . . . . . . . . . 19
4.1.2 Opening the floor-standing model . . . . . . . . . . . . . . . . 21
5 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.1 Fitting rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.2 Upgrading / exchanging main memory . . . . . . . . . . . . . 24
6 Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.1 Installing additional processors . . . . . . . . . . . . . . . . . 29
6.2 Exchanging the processor . . . . . . . . . . . . . . . . . . . . 39
6.3 Changing to dual-core processors . . . . . . . . . . . . . . . 42
6.3.1 Hardware requirements . . . . . . . . . . . . . . . . . . . . . 42
6.3.2 Software requirements . . . . . . . . . . . . . . . . . . . . . 42
6.3.3 Processor requirements . . . . . . . . . . . . . . . . . . . . . 43
6.3.4 Tasks to be performed . . . . . . . . . . . . . . . . . . . . . . 43
7 Accessible drives . . . . . . . . . . . . . . . . . . . . . . . 45
7.1 Installing a CD/DVD drive . . . . . . . . . . . . . . . . . . . . 45
7.2 Installing a tape drive . . . . . . . . . . . . . . . . . . . . . . 49
8 Controllers in non-hot-plug PCI slots . . . . . . . . . . . . 55
8.1 Installing controllers . . . . . . . . . . . . . . . . . . . . . . . 55
9 RemoteView components . . . . . . . . . . . . . . . . . . . 57
9.1 Installing the RemoteView Service Board S2 LP . . . . . . . . 57
10 External SCSI connection . . . . . . . . . . . . . . . . . . . 61
10.1 Installing an external SCSI connection . . . . . . . . . . . . . 62

Options Guide U41612-J-Z156-2-76
Contents
11 Battery for the RoMB controller . . . . . . . . . . . . . . . . 65
11.1 Installing the battery (BBU) . . . . . . . . . . . . . . . . . . . 65
12 Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
12.1 Closing the server . . . . . . . . . . . . . . . . . . . . . . . . 69
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

U41612-J-Z156-2-76 Options Guide 1
1 Preface
The PRIMERGY TX600 S2 server is an Intel-based server for mid-size and
large companies. It is suitable for use as a file server as well as an application,
information, or Internet server.
The PRIMERGY TX600 S2 server offers a high degree of reliability and avail-
ability through highly developed hardware and software components. These
include hard disk drive modules, system fans, power supply units, PCI slots and
memory boards (all the components listed are hot-pluggable), as well as
“Prefailure Detection and Analyzing” (PDA), “Automatic Server Reconfiguration
and Restart” (ASR&R) and the ServerView server management software.
The server offers a whole host of configuration options but only uses six height
units (HU) in the 19-inch rack. It is available both as a rack and a floor-standing
model.
1.1 Documentation overview
IPRIMERGY manuals are available in PDF format on the ServerBooks
DVD, which is part of the ServerView Suite package provided with each
server system.
These PDF files can also be downloaded from the Internet free of
charge: At http://manuals.fujitsu-siemens.com you will find an overview
page showing the online documentation available on the Internet.
You can go to the PRIMERGY Server documentation by clicking on
“Intel-based Servers”.
Concept and target groups
This Options Guide shows you how to expand and upgrade your server.
VCaution!
The activities described in this manual may only be performed by
specialist personnel with technical training.
IThe installation and removal of the hot-plug components is described in
the operating manual supplied with the server.

2 Options Guide U41612-J-Z156-2-76
Documentation overview Preface
Additional server documentation
The PRIMERGY TX600 S2 documentation comprises the following additional
manuals:
– The Service Supplement for PRIMERGY TX600 S2 (PDF file available on
the ServerBooks DVD supplied)
– The Operating Manual for PRIMERGY TX600 S2 (PDF file available on the
ServerBooks DVD supplied)
– The Technical Manual for the system board D1651 (PDF file available on the
ServerBooks DVD supplied)
– The “D1651 BIOS Setup Utility” manual (PDF file available on the
ServerBooks DVD supplied)
– The “ServerView Suite” manual (printed copy always supplied with the
server, and available as a PDF file on the ServerBooks DVD supplied)
– The “WebBIOS Configuration Utility” (PDF file available on the ServerBooks
DVD supplied)
– The “Security” manual (printed copy always supplied with the server, and
available as a PDF file on the ServerBooks DVD supplied)
– The “Guarantee” manual (printed copy always supplied with the server, and
available as a PDF file on the ServerBooks DVD supplied)
– The “Ergonomics” manual (PDF file available on the ServerBooks DVD
supplied)
IYou can order a supplementary ServerBooks DVD by sending an e-mail to
the following address, quoting your server data:
[e-mail]
Further sources of information:
– Technical Manual for the relevant rack
– Manual for the monitor
– Manual on ServerView Server Management
– Manual on the RemoteView Remote Test and Diagnostics System
– Documentation for boards and drives
– Documentation for your operating system
– Information files on your operating system
(see also chapter “Related publications” on page 79)

U41612-J-Z156-2-76 Options Guide 3
Preface Extensions and conversions
1.2 Extensions and conversions
Additional processors
The system board can be upgraded to include up to four processors. You may
only use processors of the same type on the system board. All processors must
have the same frequency and cache size.
The system board can also be upgraded to dual-core processors.
Extension of the main memory
The system board offers slots for four hot-plug memory boards, each of which
can accommodate up to four memory modules (in two memory banks) The slots
are suitable for DDR II/400 MHz DIMM modules with 1 GB, 2 GB and 4 GB
capacity. The board supports a maximum memory configuration of 64GB.
Additional accessible drives
In addition to the existing CD/DVD drive, two tape drives are available as acces-
sible drives. The drives are installed in the server using module frames. The
bays for the tape drives are designed for 5.25 x 1.6-inch devices.
Additional controllers in non-hot-plug PCI slots
The system board has seven PCI slots:
●Slots 1-5 are hot-plug PCI slots which can be fitted with hot-pluggable
controllers (the hot-plug PCI slots are described in the operating manual).
●Slots 6 and 7 are 100 MHz non-hot-plug PCI slots and can be fitted with
boards with a maximum length of 315mm.
Additional external SCSI interface
If you want to connect additional external SCSI devices, one channel of the
onboard controller can be made available for connecting storage subsystems
via the external SCSI interface.
Battery (BBU) for the RoMB controller
An optional battery (battery backup unit = BBU) is available for the internal
RoMB controller to protect its memory contents in the event of a power failure.

4 Options Guide U41612-J-Z156-2-76
Extensions and conversions Preface
RemoteView
RemoteView is the remote-management solution for Intel-based PRIMERGY
systems from Fujitsu Siemens Computers. RemoteView and the associated
hardware components integrated on the system board allow remote monitoring
and servicing and fast recovery of the system in the event of an error.
RemoteView Service Board S2 LP
The RemoteView Service Board S2 “low profile” (RSB S2 LP) is a PCI board with
a completely independent system, i.e. it has its own operating system with Web
server and SNMP agents and can optionally be equipped with an external
power supply.
The RSB S2 LP is installed in a (non-hot plug) standard PCI slot and connected
to the system board with a cable.
The RSB S2 LP permits remote diagnosis for system analysis, remote system
configuration and remote restart even in the event of operating system failure or
hardware faults. It has its own LAN port which ensures that all the functions are
available.

U41612-J-Z156-2-76 Options Guide 5
Preface Notational conventions
1.3 Notational conventions
The following notational conventions are used in this manual:
Italics indicate commands, menu items or software programs.
“quotation marks” indicate names of chapters and terms that need to be
emphasized.
Êindicates an activity that must be performed.
VATTENTION! indicates that, if you ignore the information given at this
point, your health, the correct functioning of your
system or the security of your data may be at risk.
Iindicates supplementary information, remarks and tips.
Table 1: Notational conventions

U41612-J-Z156-2-76 Options Guide 7
2Procedure
VATTENTION!
●The actions described in this manual should only be performed by
engineers, service personnel or technical specialists.
●Equipment repairs should only be performed by qualified staff.
●Any failure to observe the guidelines in this manual, and any unautho-
rized opening or improper repairs could endager the user (through
electric shock, fire hazards) or damage the equipment.
●Please note that any unauthorized opening of the device will result in
the invalidation of the warranty and exclusion from all liability.
ÊFirst of all please familiarize yourself with the safety instructions in the
chapter “Important notes” on page 9ff.
ÊMake sure that all the manuals you need (see “Additional server documen-
tation” on page 2) are available, printing out the PDF files if necessary.
You will definitely need
– the Operating Manual for the server,
– the Service Supplement for the server and
– the Technical Manual for the system board.
ÊShut down the server correctly, switch it off, pull out the power plug, and
open the server as described in the chapter “Preparation” on page 19f.
ÊExtend or upgrade your server as described in the relevant chapter.
IThe installation and removal of the hot-plug components is described
in the operating manual supplied with the server.
ÊClose the server, plug in the power plugs, and switch on the server as
described in the chapter “Completion” on page 69f.
ÊStart the operating system and, if necessary, configure it as required (see
the Operating Manual).

U41612-J-Z156-2-76 Options Guide 9
3 Important notes
This chapter provides safety instructions which you must observe when
handling your server.
3.1 Notes on safety
IThe following safety instructions can also be found in the manual entitled
“Safety”.
This device complies with the relevant safety regulations for data processing
equipment, including electronic office machines for use in an office
environment.
If you have any questions as to whether you can set up the device in your
particular environment, please contact your sales outlet or our customer service
center.
VATTENTION!
The activities described in this manual may only be performed by
specialist technical personnel. Equipment repairs must only be
performed by qualified staff. Any unauthorized opening or improper
repairs could endanger the user (through electric shock, energy hazard,
fire hazard) or damage the equipment. Please note that any unautho-
rized opening of the device will result in the invalidation of the warranty
and exclusion from all liability.

10 Options Guide U41612-J-Z156-2-76
Notes on safety Important notes
Before setting up
VATTENTION!
●During installation and before operating the device, observe the
instructions on environmental conditions for your device (see
operating manual).
●If the device is brought in from a cold environment, condensation may
form both inside and on the outside of the machine.
Before operating the device, wait until it is absolutely dry and has
reached approximately the same temperature as the installation site.
Failure to observe these guidelines can lead to material damage of
the device.
●Transport the device only in its original packaging or in packaging
which protects it from knocks and jolts.
Installation and operation
VATTENTION!
●If the rack model is integrated in an installation that receives power
from an industrial (public) power supply network with the IEC309
connector, the (public) power supply protection must comply with the
requirements for the non-industrial power supply networks for the
type A connector.
●The server automatically adjusts to a mains voltage between 100 V
and 240 V. Make sure that the local mains voltage is neither above nor
below this range.
●This device has safety-tested power cables and must only be
connected to properly grounded power outlets.
●Make sure that the power sockets on the device or the grounded
mains outlets are freely accessible.
●The power switch does not disconnect the device from the mains
voltage. To completely disconnect it from the mains voltage, you must
remove the power plug from the power outlet.

U41612-J-Z156-2-76 Options Guide 11
Important notes Notes on safety
VATTENTION!
ÊAlways connect the device and the attached peripherals to the same
power circuit. Otherwise you run the risk of losing data if, for example,
a power outage occurs and the central processing unit is still running
but the peripheral device (e.g. a storage subsystem) has failed.
ÊData cables must be adequately shielded to avoid interference.
ÊFor the LAN wiring, the requirements according to standards EN
50173 and EN 50174-1/2 apply. The minimum requirement is the use
of a protected LAN line of category 5 for 10/100 Mbps Ethernet,
and/or of category 5e for Gigabit Ethernet. The requirements of the
specification ISO/IEC 11801 must also be taken into account.
ÊRoute the cables in such a way that they do not form a potential
hazard (tripping) and cannot be damaged. When connecting the
device, refer to the relevant notes in the operating manual.
ÊDo not connect or disconnect any data transmission cables during a
thunderstorm (lightning hazard).
ÊBe careful to ensure that no objects (e.g. jewelry, paper clips etc.) or
liquids get inside the device (electric shock, short circuit).
ÊIn emergencies (e.g. damaged casing, control elements or cable,
penetration of liquids or foreign bodies), switch off the device immedi-
ately, unplug it from the grounded power outlet, and contact your
customer service center.
ÊProper operation of the device (in accordance with IEC 60950/EN
60950) is only ensured if the casing is completely assembled and the
rear covers for the installation openings are in place (electric shock,
cooling, fire protection, interference suppression).

12 Options Guide U41612-J-Z156-2-76
Notes on safety Important notes
VATTENTION!
ÊInstall only system extensions that satisfy the requirements and rules
governing safety, electromagnetic compatibility, and telecommunica-
tions terminal equipment.
If you install other extensions, you may damage the system or violate
these safety regulations.
Information on which system extensions are suitable can be obtained
from the customer service center or your sales outlet.
ÊThe components marked with a warning label (e.g. lightning symbol)
may only be opened, removed, or exchanged by authorized, qualified
personnel.
Exception: You may exchange hot-plug power supply units.
ÊIf you cause a defect on the device by installing or exchanging system
extensions, the warranty will be invalidated.
ÊYou may only set the resolutions and refresh rates specified in the
operating manual for your monitor.
Otherwise, you may damage the monitor. If you are in any doubt,
contact your sales outlet or customer service center.
Batteries
VATTENTION!
●Incorrect replacement of batteries may lead to risk of explosion. The
batteries may only be replaced with identical batteries or with a type
recommended by the manufacturer (see the Technical Manual for the
system board under “Related publications” on page 79).
●When replacing the lithium battery on the system board, always follow
the instructions in the technical manual for the system board (see
“Related publications” on page 79).

U41612-J-Z156-2-76 Options Guide 13
Important notes Notes on safety
Notes on handling CDs/DVDs in CD/DVD drives
VATTENTION!
●To prevent data loss, damage to the device, or injuries, you should
use only CDs/DVDs in good condition in the CD/DVD drive of your
server.
●Therefore, check each CD/DVD for damage, cracks, breakage etc.
before inserting it in the drive.
Please note that any additional labels applied may change the
mechanical properties of a CD/DVD and cause imbalance.
Damaged and imbalanced CDs/DVDs can break at high drive speeds
(data loss).
Under certain conditions, sharp-edged pieces of broken CDs/DVDs
can penetrate the cover of the drive (cause damage to the device)
and be thrown out of the device (therefore causing injury to
uncovered body parts, particularly the face or neck).
ITo protect the CD/DVD drive and prevent mechanical damage as well as
premature wearing of the CDs/DVDs, you should observe the following
advice:
– Only insert the CDs/DVDs in the drive when needed and remove
them after use.
– Store the CDs/DVDs in suitable sleeves.
– Protect the CDs/DVDs from exposure to heat and direct sunlight.
Note on the laser
The CD/DVD drive is classified as Laser Class 1, according to IEC 60825-1.
VATTENTION!
The CD/DVD drive contains a light-emitting diode (LED) which may
generate a stronger laser beam than laser class 1. It is dangerous to look
directly into the beam.
Never remove any parts of the housing of the CD/DVD drive!

14 Options Guide U41612-J-Z156-2-76
Notes on safety Important notes
Components with electrostatic-sensitive devices:
Components with electrostatic-sensitive devices are identified by the following
sticker:
Figure 1: ESD label
When you handle components fitted with ESDs, you must always observe the
following points:
●Pull out the power plug before installing or uninstalling components.
●You must always discharge static build-up (e.g. by touching a grounded
object) before working with such components.
●Any devices or tools that are used must be free of electrostatic charge.
●Wear a suitable grounding cable that connects you to the external chassis of
the system unit.
●Always hold components with ESDs at the edges or at the points marked
green (touch points).
●Do not touch any connectors or conduction paths on an ESD.
●Place all the components on a pad which is free of electrostatic charge.
IFor a detailed description of how to handle ESD components, see the
relevant European or international standards (EN 61340-5-1, ANSI/ESD
S20.20).

U41612-J-Z156-2-76 Options Guide 15
Important notes Environmental Protection
3.2 Environmental Protection
Environmentally Friendly Product Design and Development
This product has been designed in accordance with the Fujitsu Siemens
Computers standards for ”environmentally friendly product design and devel-
opment“. This means that the designers have taken into account important
criteria such as durability, selection of materials and coding, emissions,
packaging, the ease with which the product can be dismantled and the extent to
which it can be recycled.
This saves resources and thus reduces the harm done to the environment.
Notes on Saving Energy
Devices that do not have to be on permanently should not be switched on until
they need to be used and should be switched off during long breaks and on
completion of work
Notes on Dealing with Consumables
Please dispose of printer consumables and batteries in accordance with local
government regulations.
Do not throw batteries and accumulators into the household waste. They must
be disposed of in accordance with local regulations concerning special waste
(see also “Returning Batteries” on page 17).
Notes on Labeling Plastic Housing Parts
Please avoid attaching your own labels to plastic housing parts wherever
possible, since this makes it difficult to recycle them.

16 Options Guide U41612-J-Z156-2-76
Environmental Protection Important notes
Returning Used Electrical and Electronic Devices in EU Countries
●Separate collection
Users of electrical and electronic devices are obligated to collect used
devices separately. Electrical (electronic) used devices may not be disposed
of together with unsorted household refuse. The separate collection is a
condition for reuse, recycling and utilisation of used electrical (electronic)
devices, which ensures the protection of resources.
●Return and collection systems
Electrical (electronic) used devices from private households can be returned
free of charge. To return your used device, please use the country-specific
return and collection systems available to you (see “Local Contacts” on
page 17).
The return of used devices which pose a health or safety risk for human
beings due to soiling during use may be refused.
●Reuse, recycling and utilisation
By actively using the offered return and collection systems, you make your
contribution to the reuse, recycling and utilisation of electrical (electronic)
devices.
●Effects on the environment and human health
Electrical (electronic) used devices contain parts which must be handled
selectively according to the EU directive. Separate collection and selective
treatment are the basis for environment-friendly disposal and the protection
of human health.
●Meaning of the symbol "Crossed out rubbish bin on wheels"
Electrical (electronic) devices which are marked with one of the following
symbols may not be disposed of with household refuse in accordance with
the EU directive.
Figure 2: Symbols for electrical (electronic) devices