Fujitsu PRIMERGY S10 User manual

Primergy
PRIMERGY S10
Storage Subsystem
XeniaFierley
FujitsuSiemensComputersGmbHcognitasPS
85521München_Ottobrunn
e-mail:Internet:[e-mail]
Tel.:[phone]
Fax:[phone]
U41181-J-Z156-1-74
Sprachen:En
Edition October 2000

This manual is printed on
paper treated with
chlorine-free bleach.
Comments…Suggestions…Corrections…
The User Documentation Department would like to know
your opinion on this manual. Your feedback helps us to
optimize our documentation to suit your individual needs.
Fax forms for sending us your comments are included at the
back of the manual.
There you will also find the addresses of the relevant User
Documentation Department
Copyright and Trademarks
Copyright © 2000 Fujitsu Siemens Computers GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.

Introduction
Important notes
Installation
Preparation or use and operation
Troubleshooting
Related publications and index

U41181-J-Z156-1-74
Contents
1Introduction............................1
1.1 Targetgroup............................2
1.2 Notational conventions .......................2
1.3 User-friendly documentation – verified quality ...........3
1.4 Technicaldata...........................4
2 Important notes ..........................7
2.1 Notesonsafety ..........................7
2.2 Electrostatic-sensitive component label . . ............9
2.3 CEcertificate .......................... 10
2.4 RFI suppression ......................... 10
2.5 FCCnotices(FederalCommunicationsCommission)...... 10
2.6 Powercordselection....................... 11
2.6.1 For the United States and Canada ............... 11
2.6.2 For the United Kingdom ..................... 12
2.7 Notes on mounting in the rack .................. 13
2.8 Notesontransportation ..................... 14
2.9 Environmentalprotection .................... 14
3 Installation ........................... 17
3.1 Installationsteps......................... 17
3.2 Unpacking the storage subsystem ................ 18
3.3 Mounting the subsystem in the rack ............... 18
3.3.1 Routingcables.......................... 19
3.4 SettingtheSCSIID ....................... 20
3.5 Connecting the storage subsystem ............... 20
3.5.1 Connecting SCSI cables ..................... 21
3.5.2 Connecting the power cable ................... 21
3.6 Connecting and disconnecting cables . . . ........... 22
4 Preparation for use and operation .............. 23
4.1 Operating and display components ............... 23
4.2 Switchingthestoragesubsystemon/off............. 23
5 Troubleshooting ........................ 25
5.1 Opening the storage subsystem housing . ........... 25
5.2 Storage subsystem cannot be switched on ........... 26
5.3 SCSIdevicesarenotdetected ................. 27
5.4 IncorrectSCSIID ........................ 27
5.5 Fanfailure ............................ 27
5.6 Replacingthebackupunit.................... 28

U41181-J-Z156-1-74
Contents
Related publications ............................31
Index ....................................33

U41181-J-Z156-1-74 1
1 Introduction
The demand for storage capacity that is capable of scalable growth and the
increasing trend towards rack-based servers have generated a need for corre-
spondingly compact and powerful backup systems with a correspondingly
serious approach to data security.
The PRIMERGY S10 storage subsystem provides a flexible means of consoli-
dating rack-based data security. The PRIMERGY S10 makes it possible to
install present-day backup units (such as, for example, DLT 7000, DDS3,
DDS4, Autoloader, etc.) in a separate 19” cabinet and provides two 3.2”-high or
four 1.6”-high slots for this purpose. The subsystem is also prepared to accom-
modate future back up units.
The subsystem offers a simple, flexible and low-priced solution for avoiding
backup constraints and facilitating expansion.
The PRIMERGY S10 can be connected via onboard controllers or Adaptec
2940 U2W. The storage subsytem has been equipped with an LVD interface
module.
The LVD interface module accommodates the control and display elements and
the logic for controlling the power supply and monitoring the fan. It also estab-
lishes a connection between the external and internal cabling. All the necessary
connectors for the internal cabling are located on this module (socket for the
power supply, for the fan connector, and for the internal SCSI line), as well as
the socket for the external SCSI output (see also section “Connecting the
storage subsystem” on page 20). An LVD/SE SCSI terminator is integrated in
the interface and is automatically activated on the last subsystem in the string if
no SCSI connection to another storage subsystem exists (no daisy-chain).
Up to two PRIMERGY S10 can be connected to a SCSI string.
The storage subsystem is cooled by a fan. The fan is monitored to make sure it
does not fall below the nominal speed. If the “Local/Remote” switch is set to
“Remote“, the storage subsystem is switched off in the event of an error, or the
system is prevented from being switched on again, as appropriate (see also
chapter “Troubleshooting” on page 25).
The PRIMERGY S10 storage subsystem possesses an integrated power
supply unit.
The PRIMERGY S10 occupies three height units (3 HU) in the 19” rack.

2U41181-J-Z156-1-74
Target group Introduction
1.1 Target group
This manual is intended for those responsible for installing the hardware and
ensuring that the system runs smoothly. The operating manual contains all the
information required for installing and operating your system.
Knowledge of the hardware and data transfer, as well as a basic knowledge of
the operating system used, is required to understand the various expansion
options. You should also have a good working knowledge of the English
language.
1.2 Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
Text in italics indicate commands or menu item
"Quotation marks" indicate names of chapters and terms that are being
emphasized
ÊTexts which follow this symbol describe activities that
must be performed in the order shown
IThis symbol is followed by supplementary information,
remarks and tips
VPay particular attention to texts marked with this symbol.
Failure to observe this warning endangers your life,
destroys the system, or may lead to loss of data.
Table 1: Notational conventions

U41181-J-Z156-1-74 3
Introduction User-friendly documentation – verified quality
1.3 User-friendly documentation – verified
quality
As part of its efforts to further improve the information provided for users, the
editorial department responsible for this manual has been independently
audited to verify its high standards of quality of the documentation.
This audit was carried out by TÜV PRODUCT SERVICE GmbH. The following
aspects were investigated:
– General comprehensibility
– User-friendliness
– Occupational hygiene and safety for the users
– Safety of the application and observance of the relevant
regulations, standards and guidelines
– Environmental protection
– Layout, realization, readability
– Conformity with the product
– Accuracy and completeness of the contents
The criteria for the audit were developed in a joint project between
TÜV PRODUCT SERVICE GmbH and
tekom, Gesellschaft für technische Kommunikation e.V.
The DOCcert seal provides visible
evidence of the successful completion
of the audit.

4U41181-J-Z156-1-74
Technical data Introduction
1.4 Technical data
Electrical data power supply unitl
Rated voltage 100 V-125 V / 200 V-240 V
Tolerance of the rated voltage +6 % / -10 %
Rated frequency 50 Hz / 60 Hz
Max. rated current 240 V / 2,0 A
100 V / 4,0 A
Apparent power (heat transfer) max. 200 W
Power factor (PF) >65%
Effective power of typical peripheral devices
(the actual effective power will depend on the number and type of peripheral
devices installed)
DLT7000 39 W
LTO 50 W
SLR100 23.1 W
Mammoth 18 W
Magneto Optical Disk 15 W
Dimensions and weight
Height (mm) 133
Width (mm) 483
Depth (mm) 646
Weight (kg) ca. 20 (depending on configuration)

U41181-J-Z156-1-74 5
Introduction Technical data
Environmental conditions (according to DIN EN 60721-3-x)
Climate/operation (class 3K3):
Temperature(°C) 15to35
Relative humidity (%) 5 to 85
Climate/transport (class 2K2):
Temperature (°C) -25 to 60
Relative humidity (%) 15 to 98
Mechanical environmental conditions
Operation class 3M2
Transport class 2M1
Standards complied with
Product safety and ergonomics IEC 60950 (DIN EN 60950), UL 1950,
CSA 22.2 No. 950
Electromagnetic compatibility
Emitted interference EN 55022, class B; FCC part 15, class B
Noise immunity EN 50024
FCC verification Class B
CE label EMC guideline 89/339/EWG;
EN 61000-3-2; EN 61000-3-3
Product safety 73/23/EEC
Approval certification GS, CSA US/C, CB certificate
Noise development (ISO 9296) Operation
Workstation-related
sound pressure level (LpAm)
max. 56 dB(A)
Maintenance areas and ventilation distances
Specified by the rack

U41181-J-Z156-1-74 7
2 Important notes
2.1 Notes on safety
In this section you will find information that you must note when using the
storage subsystem.
This device complies with the relevant safety standards for IT equipment,
including electronic office machines, intended for use in the office environment.
IYou will also find the following safety instructions in the manual entitled
“Safety, Guarantee and Ergonomics“ which also includes other notes on
guarantee and ergonomics. Also pay attention to the notes in the manual
of the connected PRIMERGY system.
If you have any questions relating to setting up and operating your system in the
environment where you intend to use it, please consult our service organization.
V  The actions described in these instructions should only be performed
by technicians, service personnel or technical specialists. Equipment
repairs should only be performed by qualified staff. Any failure to
observe the guidelines in this manual could expose the user to risks
(electric shock, fire hazards) and could also damage the equipment.
Note that any unauthorized opening of the device will result in the
invalidation of the warranty and exclusion from all liability.
 Transport the device in its original packaging or in other suitable
packaging which will protect it against shock or impact.
 Read the notes on environmental conditions in section “Technical
data” on page 4 before setting up and operating the device.
 If the device is brought in from a cold environment, condensation may
form both inside and on the outside of the machine.
Wait until the device has acclimatized to room temperature and is
absolutely dry before starting it up. Material damage may be caused
to the device if this requirement is not observed.

8U41181-J-Z156-1-74
Notes on safety Important notes
V  Check that the rated voltage specified on the device's ID plate is the
same as the local line voltage.
 The device must only be connected to a properly grounded wall outlet
(the device is fitted with a tested and approved power cable).
 Make sure that the protective grounded outlet of the building’s wiring
system is freely accessible.
 Before opening the unit, switch off the device and then pull out the
power plugs.
 Route the cables in such a way that they do not form a potential
hazard (make sure no-one can trip over them) and that they cannot
be damaged. When connecting up a device, refer to the relevant
notes in this manual.
 Never connect or disconnect data transmission lines during a storm
(lightning hazard).
 The system unit and the directly connected external storage
subsystems should be connected to the same power supply
distributor. Otherwise you run the risk of losing data if, for example,
the central processing unit is still running but the storage subsystem
has failed during a power failure.
 Make sure that no objects (such as bracelets or paper clips) fall into
or liquids spill into the device (risk of electric shock or short circuit).
 In emergencies (e.g. damage to housings, power cords or controls or
ingress of liquids or foreign bodies), immediately power down the
device, pull out the power plugs and notify your service department.
 Note that proper operation of the system (in accordance with IEC
60950/DIN EN 60950) is guaranteed only if slot covers are installed
on all vacant slots and/or dummies on all vacant bays and the housing
cover is fitted (cooling, fire protection, RFI suppression).

U41181-J-Z156-1-74 9
Important notes Electrostatic-sensitive component label
2.2 Electrostatic-sensitive component label
Electrostatic-sensitive components may be identified by the following sticker:
Figure 1: Electrostatic-sensitive component sticker
You must follow the instructions below when handling modules containing
electrostatic-sensitive components
ÊDischarge static electricity from your body (for example by touching a
grounded metal object) before handling modules containing electrostatic-
sensitive components.
ÊThe equipment and tools you use must be free of static charge.
ÊRemove the power plug before installing or removing modules containing
electrostatic-sensitive components.
ÊOnly hold modules containing electrostatic-sensitive components by their edges.
ÊDo not touch any of the pins or track conductors on a module containing
electrostatic-sensitive components.
ÊUse a grounding strap designed for the purpose, to connect you to the system
unit as you install the modules.
ÊPlace all components on a static-safe base.
IAn exhaustive description of the handling of modules containing electro-
static-sensitive components can be found in “Guidelines on handling
electrostatic sensitive devices and modules (ESD)” or “ITS Circular
4/95”.

10 U41181-J-Z156-1-74
CE certificate Important notes
2.3 CE certificate
2.4 RFI suppression
All other equipment which is connected to this product must also have radio
noise suppression in accordance with EC Guideline 89/336/EWG.
Products which meet this requirement are accompanied by a certificate to that
effect issued by the manufacturer and/or bear the CE mark. Products which do
not meet this requirement may be operated only with the special permission of
the BZT (Bundesamt für Zulassungen in der Telekommunikation).
2.5 FCC notices (Federal Communications
Commission)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful inter-
ference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
The shipped version of this device complies with the requirements of
the EEC directives 89/336/EEC "Electromagnetic compatibility" and
73/23/EEC "Low voltage directive". The device therefore qualifies for
the CE certificate (CE=Communauté Européenne).

U41181-J-Z156-1-74 11
Important notes Power cord selection
2.6 Power cord selection
2.6.1 For the United States and Canada
Use a UL listed and CSA labeled cord set consisting of a three conductor cord
with a maximum length of 15 feet.
For units which stand on a desk or table, type SVT or SJT cord sets shall be
used.
For units which stand on floor, only SJT type cord sets shall be used.
The cord set must be selected according to the current rating for your unit.
Please consult the table below for the selection criteria for power cords used in
the United States and Canada.
The power cord for this unit has been packed
separately and has been selected according to
the country of destination. It must be used to
prevent electric shock. Use the following guide-
lines if it is necessary to replace the original cord
set.
The female receptacle of the cord set must meet
CEE-22 requirements (see Figure).
Cord Type Size of Conductors in Cord Maximum Current Rating of Unit
SJT 18 AWG
16 AWG
14 AWG
10 Amps
12 Amps
12 Amps
SVT 18 AWG
17 AWG
10 Amps
12 Amps

12 U41181-J-Z156-1-74
Power cord selection Important notes
For units set at 230 V (outside of the United States and Canada):
use a cord set consisting of a minimum AWG according to the table above and
a grounding type attachment plug rated 15 A, 250 V. The cord set should have
the appropriate safety approvals for the country in which the equipment will be
installed and should be marked HAR.
2.6.2 For the United Kingdom
Should the plug on the flexible cord not be of the type for your socket outlets, do
not use an adapter but remove the plug from the cord and discard. Carefully
prepare the end of the supply cord and fit a suitable plug.
VThis appliance must be earthed.
IMPORTANT
The wires in this mains lead are colored in accordance with the following code:
Parallel Tandem
For units set at 115 V: For units set at 230 V (domestic use):
use a parallel blade, grounding type
attachment plug rated 15 A, 125 V.
use a tandem blade, grounding type
attachment plug rated 15 A, 250 V.
Green and Yellow: Earth
Blue: Neutral
Brown: Live

U41181-J-Z156-1-74 13
Important notes Notes on mounting in the rac
k
As the colors of the wires in the mains lead of this appliance may not correspond
with the colored markings identifying the terminals in your plug, proceed as
follows:
– The wire which is colored Green and Yellow must be connected to the
terminal in the plug which is marked with the letter E or by the earth symbol
or colored Green or Green and Yellow.
– The wire which is colored Blue must be connected to the terminal which is
marked with the letter N or colored Black.
– The wire which is colored Brown must be connected to the terminal which is
marked with the letter L or colored Red.
2.7 Notes on mounting in the rack
 When connecting and disconnecting cables, observe the notes in the
documentation for your PRIMERGY system and the comments in the
"Important notes" chapter in the corresponding rack operating manual
supplied with the rack.
 Ensure that the anti-tilt bracket is correctly mounted when you set up the
rack.
 For safety reasons, no more than one unit may be withdrawn from the rack
at any one time during installation and maintenance work.
 If more than one unit is withdrawn from the rack at any one time, there is a
danger that the rack will tilt forward.
 The power supply to the rack must be installed by an authorized specialist
(electrician).

14 U41181-J-Z156-1-74
Notes on transportation Important notes
2.8 Notes on transportation
ITransport the storage subsystem in its original packaging or in other
suitable packaging which will protect it against shock or impact.
Do not unpack it until all transport maneuvers are completed.
If you need to lift or transport the storage subsystem, ask someone to
help you.
2.9 Environmental protection
Environmentally friendly product design and development
This product has been designed in accordance with the FSC standard for
“environmentally friendly product design and development”.
This means that the designers have taken into account important criteria such
as durability, selection of materials and coding, emissions, packaging, the ease
with which the product can be dismantled and the extent to which it can be
recycled.
This saves resources and thus reduces the harm done to the environment.
Notesonsavingenergy
Devices that do not have to be on permanently should not be switched on until
they need to be used and should be switched off during long breaks and on
completion of work
Notes on packaging
We recommend that you do not throw away the original packaging in case you
need it later for transportation. If possible, devices should be transported in their
original packaging.
Notes on labeling plastic housing parts
Please avoid attaching your own labels to plastic housing parts wherever
possible, since this makes it difficult to recycle them.