Fujitsu Eternus DX500 S3 Technical manual

FUJITSU Storage
ETERNUS DX500 S3/DX600 S3
Disk storage system
Site Planning Guide
P3AM-7712-05ENZ0

This page is intentionally left blank.

Preface
Fujitsu would like to thank you for purchasing our FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage
system (hereinafter referred to as ETERNUS DX).
The ETERNUS DX is designed to be connected to Fujitsu servers (Fujitsu M10, PRIMEQUEST, or PRIMERGY) or
non-Fujitsu servers.
This manual describes the environmental requirements that are necessary to install and use the ETERNUS
DX.
This manual is intended for use of the ETERNUS DX in regions other than Japan.
Please carefully review the information outlined in this manual.
Fifth Edition
December 2014
About This Manual
Organization
This manual is composed of the following two chapters:
•"Chapter 1 ETERNUS DX Installation" (page 11)
This chapter provides the installation specification of the ETERNUS DX.
•"Chapter 2 Rack Installation Specifications" (page 37)
This chapter provides the installation specification of racks.
3
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

Registered Trademarks and Trademarks
•All SPARC trademarks are used under license from SPARC International, Inc. and are trademarks or regis-
tered trademarks of that company in the United States and other countries.
•UNIX is a registered trademark of The Open Group in the United States and other countries.
•Microsoft, Windows, Windows Server, and Internet Explorer are either registered trademarks or trademarks
of Microsoft Corporation in the United States and/or other countries.
•Oracle and Java are registered trademarks of Oracle and/or its affiliates.
•HP-UX is a trademark of Hewlett-Packard Company in the U.S. and other countries.
•Mozilla, Firefox, and the Mozilla and Firefox logos are trademarks or registered trademarks of the Mozilla
Foundation in the United States and other countries.
•Red Hat is a registered trademark of Red Hat, Inc. in the U.S. and other countries.
•Linux is a registered trademark of Linus Torvalds.
•SUSE is a registered trademark of Novell, Inc. in the United States and other countries.
•IBM, AIX, and Tivoli are trademarks of International Business Machines Corporation, registered in many ju-
risdictions worldwide.
•VMware, VMware logos, Virtual SMP, and vMotion are either registered trademarks or trademarks of
VMware, Inc. in the U.S. and/or other countries.
•ARCserve® products and logos are registered trademarks of CA Technologies.
•The company names, product names and service names mentioned in this document are registered trade-
marks or trademarks of their respective companies.
•Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
Naming Conventions
■Product Names
•The following abbreviations are used for Microsoft® Windows Server®.
Product name Abbreviation
Microsoft® Windows Server® 2003, Datacenter Edition Windows Server 2003
Microsoft® Windows Server® 2003, Enterprise Edition
Microsoft® Windows Server® 2003, Standard Edition
Microsoft® Windows Server® 2008 Datacenter
Microsoft® Windows Server® 2008 R2 Datacenter
Windows Server 2008
Microsoft® Windows Server® 2008 Enterprise
Microsoft® Windows Server® 2008 R2 Enterprise
Microsoft® Windows Server® 2008 Standard
Microsoft® Windows Server® 2008 R2 Standard
Microsoft® Windows Server® 2008 for Itanium-Based Systems
Microsoft® Windows Server® 2008 R2 for Itanium-Based Systems
Microsoft® Windows Server® 2008 HPC Edition
Microsoft® Windows Server® 2008 R2 HPC Edition
Preface
4
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

Product name Abbreviation
Microsoft® Windows Server® 2012 Datacenter
Microsoft® Windows Server® 2012 R2 Datacenter
Windows Server 2012
Microsoft® Windows Server® 2012 Standard
Microsoft® Windows Server® 2012 R2 Standard
Microsoft® Windows Server® 2012 Essentials
Microsoft® Windows Server® 2012 R2 Essentials
•The following abbreviations are used for Red Hat Linux.
Product name Abbreviation
Red Hat Enterprise Linux 5 (for x86)
Red Hat Enterprise Linux 5 (for Intel64)
Red Hat Enterprise Linux 5
Red Hat Enterprise Linux 6 (for x86)
Red Hat Enterprise Linux 6 (for Intel64)
Red Hat Enterprise Linux 6
Red Hat Enterprise Linux 7 (for Intel 64) Red Hat Enterprise Linux 7
■Symbols Used in This Manual
The following symbol is used throughout this manual:
This indicates information for the user to note when using the ETERNUS DX. Please be
sure to read this information.
This indicates supplementary and reference information.
■Abbreviations Used in This Manual
•"ETERNUS DX500 S3" refers to the FUJITSU Storage ETERNUS DX500 S3 Disk storage system and "ETERNUS
DX600 S3" refers to the FUJITSU Storage ETERNUS DX600 S3 Disk storage system.
•"ETERNUS DX" refers to the ETERNUS DX500 S3 and ETERNUS DX600 S3 Disk storage systems.
•"CA" refers to a host interface module that is used in an ETERNUS DX to connect to a server.
•"Host Bus Adapter (HBA)" refers to the interface module that is normally used by the server to connect to
ETERNUS DX storage systems.
•Trademark symbols such as ™ and ® are omitted in this document.
Preface
5
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

Warning Signs
Warning signs are shown throughout this manual in order to prevent injury to the user and/or material dam-
age. These signs are composed of a symbol and a message describing the recommended level of caution.
The following explains the symbol, its level of caution, and its meaning as used in this manual.
This symbol indicates the possibility of serious or fatal injury if the ETERNUS DX is not
used properly.
This symbol indicates the possibility of minor or moderate personal injury, as well as
damage to the ETERNUS DX and/or to other users and their property, if the ETERNUS DX
is not used properly.
This symbol indicates IMPORTANT information for the user to note when using the ETER-
NUS DX.
The following symbols are used to indicate the type of warnings or cautions being described.
Electric Shock
The triangle emphasizes the urgency of the WARNING and CAUTION contents. Inside
the triangle and above it are details concerning the symbol (e.g. Electrical Shock).
No Disassembly
The barred "Do Not..." circle warns against certain actions. The action which must be
avoided is both illustrated inside the barred circle and written above it (e.g. No Disas-
sembly).
Unplug
The black "Must Do..." circle indicates actions that must be taken. The required ac-
tion is both illustrated inside the black disk and written above it (e.g. Unplug).
Preface
6
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

How Warnings are Presented in This Manual
A message is written beside the symbol indicating the caution level. This message is marked with a vertical
ribbon in the left margin, to distinguish this warning from ordinary descriptions.
A display example is shown here.
Warning level indicator
Warning type indicator
Warning details
•To avoid damaging the ETERNUS DX, pay attention to the following points
when cleaning the ETERNUS DX:
- Make sure to disconnect the power when cleaning.
- Be careful that no liquid seeps into the ETERNUS DX when using
cleaners, etc.
- Do not use alcohol or other solvents to clean the ETERNUS DX.
Warning layout ribbon
Example warning
CAUTION Do
Preface
7
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

Table of Contents
Chapter 1 ETERNUS DX Installation 11
1.1 Installation Specifications ............................................................................................................ 11
1.1.1 ETERNUS DX500 S3 .............................................................................................................................................11
1.1.2 ETERNUS DX600 S3 .............................................................................................................................................13
1.2 Storage System Dimensions ......................................................................................................... 15
1.3 Compliance Standards.................................................................................................................. 20
1.4 Package Size ................................................................................................................................ 21
1.5 Installation Area........................................................................................................................... 22
1.6 Installation Environment.............................................................................................................. 24
1.6.1 Air Conditioning..................................................................................................................................................24
1.6.2 Installation Methods...........................................................................................................................................25
1.6.3 Load Bearing Capacity for Floors.........................................................................................................................25
1.7 Outlet/Socket Specifications ......................................................................................................... 26
1.7.1 Specifications for Optional Power Supply Products..............................................................................................27
1.7.2 Required Number of Outlets/Sockets...................................................................................................................30
1.7.3 Circuit Protectors.................................................................................................................................................31
1.7.4 Input Power Supply Lines....................................................................................................................................35
Chapter 2 Rack Installation Specifications 37
2.1 Rack Installation Requirements.................................................................................................... 37
2.1.1 Placement in the Rack ........................................................................................................................................37
2.1.2 Cable Connection ................................................................................................................................................38
2.2 Installable Racks .......................................................................................................................... 48
2.2.1 Fujitsu Racks.......................................................................................................................................................48
2.2.2 Non-Fujitsu Racks ...............................................................................................................................................48
8
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

List of Figures
Figure 1.1 Controller Enclosure Dimensions..............................................................................................................15
Figure 1.2 2.5" Type Drive Enclosure Dimensions......................................................................................................16
Figure 1.3 3.5" Type Drive Enclosure Dimensions......................................................................................................17
Figure 1.4 High-density Drive Enclosure Dimensions ................................................................................................18
Figure 1.5 19-inch Rack Dimensions .........................................................................................................................19
Figure 1.6 Installation Area and Service Area............................................................................................................22
Figure 1.7 Installation and Service Areas (When a High-density Drive Enclosure is Installed_1)...............................22
Figure 1.8 Installation and Service Areas (When a High-density Drive Enclosure is Installed_2)...............................23
Figure 1.9 Service Area (When a High-density Drive Enclosure is Installed in the Top Part of the Rack) ...................23
Figure 1.10 Dimensions of the Location on a Floor in which a Rack is Secured ...........................................................25
Figure 1.11 Power Distribution Units (1U) ..................................................................................................................28
Figure 1.12 Power Distribution Units (2U) ..................................................................................................................29
Figure 1.13 Breaking Characteristics of Distribution Board Circuit Protectors ..............................................................32
Figure 1.14 Example of a Power Supply Connection When a Power Distribution Unit (1U) is Used .............................33
Figure 1.15 Example of a Power Supply Connection When a Power Distribution Unit (2U) is Used .............................34
Figure 1.16 Example of a Power Supply Connection When a Power Distribution Unit is not Used...............................35
Figure 1.17 Input Power Supply Lines (When Connecting to Power Sockets) ..............................................................35
Figure 1.18 Input Power Supply Lines (When Connecting to UPS)...............................................................................36
Figure 2.1 AC Cable Connection.................................................................................................................................38
Figure 2.2 Connection Example 1 (ETERNUS DX500 S3 Connections in the Same Rack)............................................40
Figure 2.3 Connection Example 2 (ETERNUS DX500 S3 Connections in the Same Rack)............................................41
Figure 2.4 Connection Example 3 (ETERNUS DX500 S3 Connections in the Same Rack)............................................42
Figure 2.5 Connection Example 4 (ETERNUS DX500 S3 Connections in Multiple Racks) ............................................43
Figure 2.6 Connection Example 1 (ETERNUS DX600 S3 Connections in the Same Rack)............................................44
Figure 2.7 Connection Example 2 (ETERNUS DX600 S3 Connections in the Same Rack)............................................45
Figure 2.8 Connection Example 3 (ETERNUS DX600 S3 Connections in the Same Rack)............................................46
Figure 2.9 Connection Example 4 (ETERNUS DX600 S3 Connections in Multiple Racks) ............................................47
Figure 2.10 Unit Installation Area ...............................................................................................................................49
9
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

List of Tables
Table 1.1 ETERNUS DX500 S3 Installation Specifications .........................................................................................11
Table 1.2 ETERNUS DX600 S3 Installation Specifications .........................................................................................13
Table 1.3 Package Size (for Regions other than EMEA&I) ........................................................................................21
Table 1.4 Rating of the Current for Each Power Cord................................................................................................26
Table 1.5 Specifications for AC200V Power Cords (for the EMEA&I Region)..............................................................27
Table 1.6 Specifications for AC200V Power Cords (for Regions Other than EMEA&I).................................................27
Table 1.7 Specifications for AC125V Power Cords (for Regions Other than EMEA&I).................................................28
Table 1.8 Specifications for Power Cords (for Regions Other than EMEA&I) .............................................................28
Table 1.9 Required Number of Outlets and Sockets to Install Power Distribution Units ...........................................28
Table 1.10 Power Distribution Unit (AC200-240V, 1U, 4 Outlets) Specifications ........................................................29
Table 1.11 Power Distribution Unit (AC200-240V, 2U, 12 Outlets) Specifications ......................................................29
Table 1.12 Power Distribution Unit (AC200-240V, 2U, 16 Outlets) Specifications ......................................................30
Table 1.13 Required Conditions for Distribution Board Circuit Protectors...................................................................31
Table 2.1 Enclosure Installation Order .....................................................................................................................37
Table 2.2 Usage of Cables for Connecting Enclosures...............................................................................................39
Table 2.3 Specifications for the Unit Installation Area .............................................................................................49
10
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

Chapter 1
ETERNUS DX Installation
This chapter explains the installation of the ETERNUS DX.
1.1 Installation Specifications
1.1.1 ETERNUS DX500 S3
The following table shows the installation specifications of the ETERNUS DX500 S3.
Table 1.1 ETERNUS DX500 S3 Installation Specifications
Item ETERNUS DX500 S3
Dimensions
(W ´ D ´ H)
Controller enclosure 482 ´ 805 ´ 133mm (3U)
Drive enclosure 2.5" type 482 ´ 540 ´ 88mm (2U)
3.5" type 482 ´ 560 ´ 88mm (2U)
High-density
type
482 ´ 980 ´ 176mm (4U)
Power distribution unit 1U 435 ´ 148 ´ 38mm
2U (485 ´ 280 ´ 43mm) ´ 2 (*1)
Maximum weight
(approx.)
Controller enclosure 54kg
Drive enclosure (*2) 2.5" type 35kg
3.5" type 35kg
High-density
type
95kg
Power distribution unit 1U 2kg
2U (6kg) ´ 2 (*1)
Power Voltage AC 100 – 120V, AC 200 – 240V
Phase Single
Frequency 50Hz/60Hz
Maximum power
consumption
Controller enclosure AC 100 – 120V 650W (660VA)
AC 200 – 240V 760W (770VA)
Drive enclosure
(*2)
2.5" type AC 100 – 120V 430W (440VA)
AC 200 – 240V 430W (440VA)
3.5" type AC 100 – 120V 340W (350VA)
AC 200 – 240V 340W (350VA)
High-density
type
AC 100 – 120V 1,300W (1,320VA)
AC 200 – 240V 1,300W (1,320VA)
11
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

Item ETERNUS DX500 S3
Maximum heat
generation
Controller enclosure AC 100 – 120V 2,400kJ/h
AC 200 – 240V 2,800kJ/h
Drive enclosure
(*2)
2.5" type AC 100 – 120V 1,600kJ/h
AC 200 – 240V 1,600kJ/h
3.5" type AC 100 – 120V 1,300kJ/h
AC 200 – 240V 1,300kJ/h
High-density
type
AC 100 – 120V 4,700kJ/h
AC 200 – 240V 4,700kJ/h
Maximum
amount of ex-
haust air
Controller enclosure 5.1m3/min
Drive enclosure (*3) 2.5" type 4.0m3/min
3.5" type 4.0m3/min
High-density
type 12.0m3/min
Environmental
conditions
Temperature Operating 10 – 40°C
Not operating 0 – 50°C
Shipping -40 – 60°C
Temperature gradient 15°C/Hr or less
Humidity Operating 20 – 80%RH
Not operating 8 – 80%RH
Shipping 8 – 90%RH
Humidity gradient 30%/day or less
Maximum wet bulb temperature 29°C
Altitude above sea level 0 – 3000m
Airborne dust 0.15mg/m3 or less
Gas concentration tolerance level Cl2: 3.4ppb or less, H2S: 7.1ppb or less,
SO2: 37ppb or less, NH3: 420ppb or less,
NO2: 52ppb or less, O3: 5ppb or less,
HCl: 6.6ppb or less, HF: 3.6ppb or less
Oil vapor 0.2mg/m3 or less
Seawater (salt corrosion) If the ETERNUS DX is installed on the ocean or
premises within 0.5km from the coast, necessary
measures must be taken to prevent salt corro-
sion.
Vibration limit Operating 400gal
Not operating 1,000gal
Noise emission
(*3)
Sound Pressure Level 53dB (A)
Sound Power Level 7.0B
*1: A 2U power distribution unit is composed of two 1U power distribution units.
*2: These values are for each drive enclosure when 24 drives are installed in a 2.5" type drive enclosure, 12
drives are installed in a 3.5" type drive enclosure, or 60 drives are installed in a high-density drive en-
closure.
Chapter 1 ETERNUS DX Installation
1.1 Installation Specifications
12
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

*3: These values are measured when a single controller enclosure and four drive enclosures are configured
in an environment in which the temperature is 23 ± 2 °C.
1.1.2 ETERNUS DX600 S3
The following table shows the installation specifications of the ETERNUS DX600 S3.
Table 1.2 ETERNUS DX600 S3 Installation Specifications
Item ETERNUS DX600 S3
Dimensions
(W ´ D ´ H)
Controller enclosure 482 ´ 805 ´ 133mm (3U)
Drive enclosure 2.5" type 482 ´ 540 ´ 88mm (2U)
3.5" type 482 ´ 560 ´ 88mm (2U)
High-density
type
482 ´ 980 ´ 176mm (4U)
Power distribution unit 1U 435 ´ 148 ´ 38mm
2U (485 ´ 280 ´ 43mm) ´ 2 (*1)
Maximum weight
(approx.)
Controller enclosure 54kg
Drive enclosure (*2) 2.5" type 35kg
3.5" type 35kg
High-density
type
95kg
Power distribution unit 1U 2kg
2U (6kg) ´ 2 (*1)
Power Voltage AC 100 – 120V, AC 200 – 240V
Phase Single
Frequency 50Hz/60Hz
Maximum power
consumption
Controller enclosure AC 100 – 120V 720W (730VA)
AC 200 – 240V 1,000W (1,010VA)
Drive enclosure
(*2)
2.5" type AC 100 – 120V 430W (440VA)
AC 200 – 240V 430W (440VA)
3.5" type AC 100 – 120V 340W (350VA)
AC 200 – 240V 340W (350VA)
High-density
type
AC 100 – 120V 1,300W (1,320VA)
AC 200 – 240V 1,300W (1,320VA)
Maximum heat
generation
Controller enclosure AC 100 – 120V 2,600kJ/h
AC 200 – 240V 3,600kJ/h
Drive enclosure
(*2)
2.5" type AC 100 – 120V 1,600kJ/h
AC 200 – 240V 1,600kJ/h
3.5" type AC 100 – 120V 1,300kJ/h
AC 200 – 240V 1,300kJ/h
High-density
type
AC 100 – 120V 4,700kJ/h
AC 200 – 240V 4,700kJ/h
Chapter 1 ETERNUS DX Installation
1.1 Installation Specifications
13
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

Item ETERNUS DX600 S3
Maximum
amount of ex-
haust air
Controller enclosure 6.2m3/min
Drive enclosure (*3) 2.5" type 4.0m3/min
3.5" type 4.0m3/min
High-density
type 12.0m3/min
Environmental
conditions
Temperature Operating 10 – 40°C
Not operating 0 – 50°C
Shipping -40 – 60°C
Temperature gradient 15°C/Hr or less
Humidity Operating 20 – 80%RH
Not operating 8 – 80%RH
Shipping 8 – 90%RH
Humidity gradient 30%/day or less
Maximum wet bulb temperature 29°C
Altitude above sea level 0 – 3000m
Airborne dust 0.15mg/m3 or less
Gas concentration tolerance level Cl2: 3.4ppb or less, H2S: 7.1ppb or less,
SO2: 37ppb or less, NH3: 420ppb or less,
NO2: 52ppb or less, O3: 5ppb or less,
HCl: 6.6ppb or less, HF: 3.6ppb or less
Oil vapor 0.2mg/m3 or less
Seawater (salt corrosion) If the ETERNUS DX is installed on the ocean or
premises within 0.5km from the coast, necessary
measures must be taken to prevent salt corro-
sion.
Vibration limit Operating 400gal
Not operating 1,000gal
Noise emission
(*3)
Sound Pressure Level 54dB (A)
Sound Power Level 7.2B
*1: A 2U power distribution unit is composed of two 1U power distribution units.
*2: These values are for each drive enclosure when 24 drives are installed in a 2.5" type drive enclosure, 12
drives are installed in a 3.5" type drive enclosure, or 60 drives are installed in a high-density drive en-
closure.
*3: These values are measured when a single controller enclosure and four drive enclosures are configured
in an environment in which the temperature is 23 ± 2 °C.
Chapter 1 ETERNUS DX Installation
1.1 Installation Specifications
14
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

1.2 Storage System Dimensions
■Controller Enclosure Dimensions
The following diagrams show the dimensions of a controller enclosure.
The dimension values do not include any protruding parts (approximation).
Figure 1.1 Controller Enclosure Dimensions
805mm133mm
482mm
Top
Front
Side
Chapter 1 ETERNUS DX Installation
1.2 Storage System Dimensions
15
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

■Drive Enclosure Dimensions
●2.5" Type Drive Enclosure
The diagrams below show the dimensions of a 2.5" type drive enclosure.
The dimension values do not include any protruding parts (approximation).
Figure 1.2 2.5" Type Drive Enclosure Dimensions
540mm
88mm
482mm
Top
Front
Side
Chapter 1 ETERNUS DX Installation
1.2 Storage System Dimensions
16
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

●3.5" Type Drive Enclosure
The diagrams below show the dimensions of a 3.5" type drive enclosure.
The dimension values do not include any protruding parts (approximation).
Figure 1.3 3.5" Type Drive Enclosure Dimensions
560mm88mm
482mm
Top
Front
Side
Chapter 1 ETERNUS DX Installation
1.2 Storage System Dimensions
17
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

●High-density Drive Enclosure
The diagrams below show the dimensions of a high-density drive enclosure.
The dimension values do not include any protruding parts (approximation).
Figure 1.4 High-density Drive Enclosure Dimensions
980mm
176mm
482mm
Top
Front
Side
Chapter 1 ETERNUS DX Installation
1.2 Storage System Dimensions
18
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

■Rack Dimensions
The following diagrams show the dimensions of a 19-inch rack. The dimension values do not include any
protruding parts (approximation).
For details on the specification information that is required for securing a rack, refer to Figure 1.10.
Figure 1.5 19-inch Rack Dimensions
Front Rear
Bottom
2,000mm
1,050mm
700mm
Side
Top
Chapter 1 ETERNUS DX Installation
1.2 Storage System Dimensions
19
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0

1.3 Compliance Standards
●Compliance Standards
•Product safety
UL60950-1, CSA-C22.2 No.60950-1, EN60950-1, IEC60950-1, TP TC 004/2011
•Electromagnetic Compatibility
CNS13438 (C6357) Class A, FCC CFR47 part 15 Class A, ICES-003 Class A, EN55022 Class A, VCCI Class A,
AS/NZS CISPR22 Class A, TP TC 020/2011
•Electromagnetic Immunity
EN55024
•CE certification
Electromagnetic Compatibility Directive 2004/108/EC
Low Voltage Directive 2006/95/EC
•Environmental compliance
RoHS-compliant (Restriction of hazardous substances)
WEEE-compliant (Waste electrical and electronic equipment)
•80PLUS GOLD (power conversion efficiency)
Chapter 1 ETERNUS DX Installation
1.3 Compliance Standards
20
FUJITSU Storage ETERNUS DX500 S3/DX600 S3 Disk storage system Site Planning Guide
Copyright 2014 FUJITSU LIMITED
P3AM-7712-05ENZ0