Fukuda EK-226P User manual

EK-226P
INSTRUCTIONS
Supplied by Laser Levels Online – The Laser Level Specialists
www.laser-level.co.uk Tel: [phone]
Thank you for purchasing the EK-226P automatic Cross Line Laser Level kit.
These instructions are intended to explain the quick basics to operating this
equipment. If you need any more information, or the unit requires calibration
or repair, then please contact our Service Dept on tel [phone] or
fax [phone]. We are here to help.
Power source:
Unscrew the battery cover & remove carefully.
Fit 3 x type AA alkaline batteries. Take care with correct polarity as marked
on the case. Refit the battery cover. The EK-226P will accept rechargeable
batteries but there is no provision for charging in the laser. You will need to
charge these batteries externally. We would also recommend that a spare set
of batteries are kept in the carry case as a back-up.
Positioning the Laser:
Mount the EK-226P on a generally level, firm surface or 5/8” threaded Tripod.
(note: an adapter may be required) To operate correctly, this surface must be
within +/-3 deg of true horizontal. Use the top bubble level as a "guide".
1

Principle of Operation:
It is important to note that this bubble level does NOT set the accuracy of the
level. The EK-226P has a fully automatic pendulum system to set true level.
IF THE EK-226P EMITS CONTINUOUS RED LASER LINES ie. not
flashing, THEN THEY WILL BE TRUE LEVEL & PLUMB.
This laser can be used Indoors or Outside, where it is waterproof to IP54.
Controls:
A simple ON/OFF switch combined with a black transit latch is located on the
side of the case. Position laser & centralise the bubble level, as described
above. Switch ON - the top "H" LED will illuminate green & the horizontal red
laser line will project onto the wall opposite. To switch OFF, press button "H"
again.
A second button marked V1/V2 is used to switch both of the vertical laser
plumb lines ON or OFF, either together or independently.
*Outdoor button - see details below, in the laser Detector Procedure
section.
Working Range:
Depending on ambient lighting - generally 50m with detector & 10m without.
To set Squaring:
The EK-226P does have a squaring facility to set out 90 degrees.
Place the instrument on the floor & operate BOTH vertical lines. These will
project along the floor (to set floor squaring), up the walls opposite & square
on the ceiling above too.
The body of the laser can be slowly rotated by hand, keeping the feet in the
same position. This gives a coarse setting on any plumb (vertical) lines.
The User can adjust the fine setting cross spindle to finalise line positions.
To set Plumb:
Again, switch on BOTH vertical lines. The Cross on the ceiling is true plumb
with the red DOT below the instrument. This is an electronic equivalent of a
plumb string line - a very convenient & useful feature.
2

To Switch OFF:
Simply turn the transit latch to OFF / LOCK.
Detector model FD-9R
(colour may vary)
Fit the supplied 9V battery, polarity marked. Power up via left hand ON/OFF
button. The mode button is not used.
The User can switch the sounder On or OFF, as required with the right hand
press button.
Bright LED's next to the red pick-up window show above/below or SET LEVEL.
Both side & rear LED's simply repeat the main front display.
Use with or without its staff mounting bracket. Spare brackets are available.
Detector Procedure:
SWITCH ON the *OUTDOOR button.
Face the detector towards the EK-226P & find the centreline of the laser
beams via the red pick-up window. Obtain a continuous tone for perfect level.
Mark out.
Outdoor use....
If the sun is low in the sky & shining into the red window, shield it with a
cupped hand to prevent false readings. Positioning the EK-226P laser itself in
full sun is no problem but the detector window can in some instances, be
affected by direct bright sunlight or reflections. So please take extra care!
Important
Only switch on the Outdoor button when you need a "pulsed output" to
operate the detector. This will save battery power & make the normal red
3

laser lines brighter - for general use.
cont....
SAFETY PRECAUTIONS:
Comply with class II laser operating safety procedures.
Display a Laser Safety Notice in the working area.
General Advice:
This is an accurate measuring device - so to give good service, look after it!
Prevent the EK-226P from receiving severe knocks, bangs or vibration.
Store the laser & its accessories in the supplied, foam-lined carry case.
If wet, dry before storing & keep in storage temperatures between 5 - 30 deg
C.
For long-term storage, remove all batteries - to prevent any internal damage.
There are NO User serviceable parts.
We offer a full Back-up service including calibration & usage advice.
Accessories for the various Trades are also available - on request.
eg. Floor-to-ceiling Pillar kits, tripods, staffs, wall brackets & adapters etc.
To contact us:
P.R.Engineering Ltd, Unit 35 Bridge Business Centre,
Beresford Way, CHESTERFIELD, S41 9FG. England.
Tel: [phone] / Fax: [phone]
4

[e-mail] www.laser-level.co.uk
5