Fuller Brush FB-BFM User manual

Owner’s Manual
For The Fuller Brush
BARE FLOOR Maid Vacuum
Thank you for purchasing this
Fuller Brush Broom Vacuum.
To ensure the best results, please read this
manual and keep it for reference.
Model
FB-BFM

1
Important Safety Instructions � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2
Two-Wire Polarized Cord � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
Parts Identification � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
Replacement Filter & Microfiber Polishing Pads � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
How to Assemble the Vacuum � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5-6
How to Operate the Vacuum � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7
How to Empty the Dust Cup � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8
How to Replace the Filter� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9
Maintenance and Care� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10
Troubleshooting � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 11
For Best Performance � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 11
Warranty � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12
The model and serial numbers of this product may be found on the back side of the unit� You should register your
vacuum online at www�FullerBrushVacuums�com as soon as possible for your protection� Also, note the model and serial
numbers of your unit in the spaces provided below, and retain this book as a permanent record of your purchase�
Model Number _____________________________________________________________________________________
Serial Number ______________________________________________________________________________________
Date Purchased _____________________________________________________________________________________
Your Fuller Brush vacuum cleaner is a product of high-quality materials and superior workmanship� We urge you to
read these operating instructions carefully before you use this vacuum cleaner in order to obtain the full performance and
satisfaction it can offer you�
Before you plug in your Fuller Brush vacuum cleaner, make sure the voltage indicated on the rating plate located on the
back of the vacuum is the same as your local supply�
Index
Customer’s Record
Save These Instructions

2
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the
following:
READ ALL INSTRUCTIONS BEFORE
USING THIS APPLIANCE
The manufacturer cannot accept responsibility for damage caused
when the appliance is not used according to the
instructions, or for uses other than those for which it
was intended.
To reduce the risk of fire, electric shock or injury:
• Do not leave appliance when plugged in.
Unplug from outlet when not in use and
before servicing.
• WARNING: ELECTRIC SHOCK COULD OCCUR IF
USED OUTDOORS OR ON WET SURFACES.
• Do not allow to be used as a toy. Close
attention is necessary when used by or near
children.
• Use only as described in this manual. Use only
manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. Or if
appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped
into water.
• Do not pull or carry by cord, use cord as a
handle, close a door on the cord, or pull cord
around sharp edges or corners. Do not run
appliance over cord. Keep cord away from
heated surfaces.
• Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
• Do not handle plug or appliance with
wet hands.
• Do not put any object into openings. Do not
use with any opening blocked; keep free of
dust, lint, hair and anything that may reduce
air flow.
• Keep hair, loose clothing, fingers and all parts
of body away from openings and moving
parts.
• Do not pick up anything that is burning or
smoking, such as cigarettes, matches or hot
ashes.
• Do not use without filters in place.
• Turn off all controls before unplugging.
• Do not use to pick up flammable or
combustible liquids such as gasoline or use in
areas where they may be present.
• Do not attempt to service the unit while
appliance is plugged in.
• Do not use vacuum to pick up water or any
wet materials.
• Use extra care when cleaning on stairs.
SAVE THESE INSTRUCTIONS.
WARNING:

3
Two-Wire Polarized Cord
To reduce the risk of electric shock, this product is equipped with a polarized alternating
current line plug (a plug having one blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the plug still does not fit, contact a
qualified electrician to replace the obsolete outlet. Do not defeat the safety purpose of
the polarized plug.
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to
cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to
cause birth defects or other reproductive harm.
Two-Wire Polarization Instructions

4
• Genuine Fuller Brush High Flow Filter
Part # FBQM-HFF
• Genuine Fuller Brush Microfiber Polishing Pads
Part # BFM-P
Parts Identification
Replacement Filters & Polishing Pads
On/Off
Button
Floor
Nozzle
Dust Cup Release Button
(to remove dust cup from
the vacuum)
Dust Cup
Handle
Power Cord
Cord Hooks
Main Body
Microfiber
Polishing Pad

5
Attaching the Handle
With the On/Off button facing the front of
the vacuum, insert the handle into the top
of the vacuum until it clicks into place (Fig. 1).
Attaching the Dust Cup Assembly
Line up the bottom of the dust cup with the base
of the vacuum. Then push the top of
the dust cup into the vacuum until it clicks
into place (Fig. 2).
Removing the Dust Cup Assembly
Push the dust cup release button and
remove the dust cup assembly from the
vacuum (Fig. 3).
How to Assemble the Vacuum
Fig. 1
Installation and removal of dust cup component
When dust cup is installed, please firstly check whether internal parts
of dust cup component are installed completely or not. Missed
installation should be avoided. Please firstly align to clamp at the
bottom of dust cup during installation. After the bottom of dust cup is
correctly aligned, dust cup component can be directly pulled into main
body, and reliable assembly can be ensured after locking sound is
heard.
If dust cup is should be removed, dust cup release button should be
pressed, and the dust cup should be removed according to direction in
the drawing.
Fig. 2
Installation and removal of dust cup component
When dust cup is installed, please firstly check whether internal parts
of dust cup component are installed completely or not. Missed
installation should be avoided. Please firstly align to clamp at the
bottom of dust cup during installation. After the bottom of dust cup is
correctly aligned, dust cup component can be directly pulled into main
body, and reliable assembly can be ensured after locking sound is
heard.
If dust cup is should be removed, dust cup release button should be
pressed, and the dust cup should be removed according to direction in
the drawing.
Fig. 3

6
Fig. 1
Fig. 2
How to Assemble the Vacuum
Attaching the Floor Nozzle
Place the floor nozzle on the floor with the neck
locked in the upright position. Line up the neck of
the floor nozzle with the inlet at the base of the
vacuum. Push until it clicks into place (Fig. 1).
Removing the Floor Nozzle
Press the metal button at the base of the vacuum
with a screw driver or other pointed tool. Then
remove the floor nozzle from the inlet (Fig. 2).
Attaching the Power Cord
Attach the cord to the clip on the back of the
handle, then wrap the cord around the upper
and lower cord hooks (Fig. 3).
Unwinding the Power Cord
The upper cord hook rotates to allow for quick
access to the power cord. Turn the upper cord
hook downward and you can quickly drop the
power cord to the floor without unwinding it from
the cord hooks.
When storing the vacuum cleaner, turn the upper
cord hook to the upright position and wrap the
power cord around the cord storage hooks (Fig. 4).
Fig. 4
Fig. 3

7
On/Off Button
Push the power button on the handle
(Fig. 1) to turn on the vacuum. Press the
power button again to turn off the vacuum.
Reclining the Vacuum
Place your foot on the top of the floor
nozzle and pull the handle toward you
(Fig. 2).
Vacuuming Rugs
The Bare Floor Maid is designed to sweep
and polish your bare floors in one easy step
thanks to the strong vacuum suction and
microfiber polishing pad. This microfiber
polishing pad prevents the vacuum from
gliding over rugs or carpet. Remove the
microfiber polishing pad from the bottom of
the floor nozzle to vacuum rugs or low pile
carpet (Fig. 3).
Fig. 1
Fig. 2
Fig. 3
How to Operate the Vacuum

8
WARNING: Empty the dust cup after each use
or before the contents reach the “MAX FILL”
line on the dust cup. Over-filling the dust cup
may cause dirt and debris to clog the filter and
cause loss of suction.
• Remove the dust cup from the vacuum by
pressing the dust cup release button on top of
the dust cup (Fig. 1).
• Remove the filter assembly by pulling it up
and out of the dust cup (Fig. 2).
• Tip the dust cup upside down over a trash
can to empty contents.
• Replace the filter assembly by lining up the
notches on the filter and the dust cup and
pushing straight down (Fig. 3).
• Replace the dust cup onto the vacuum body
and resume vacuuming (Fig. 4).
Installation and removal of dust cup component
When dust cup is installed, please firstly check whether internal parts
of dust cup component are installed completely or not. Missed
installation should be avoided. Please firstly align to clamp at the
bottom of dust cup during installation. After the bottom of dust cup is
correctly aligned, dust cup component can be directly pulled into main
body, and reliable assembly can be ensured after locking sound is
heard.
If dust cup is should be removed, dust cup release button should be
pressed, and the dust cup should be removed according to direction in
the drawing.
Installation and removal of dust cup component
When dust cup is installed, please firstly check whether internal parts
of dust cup component are installed completely or not. Missed
installation should be avoided. Please firstly align to clamp at the
bottom of dust cup during installation. After the bottom of dust cup is
correctly aligned, dust cup component can be directly pulled into main
body, and reliable assembly can be ensured after locking sound is
heard.
If dust cup is should be removed, dust cup release button should be
pressed, and the dust cup should be removed according to direction in
the drawing.
Fig. 1
Fig. 4
Fig. 2
Fig. 3
How to Empty the Dust Cup

9
Installation and removal of dust cup component
When dust cup is installed, please firstly check whether internal parts
of dust cup component are installed completely or not. Missed
installation should be avoided. Please firstly align to clamp at the
bottom of dust cup during installation. After the bottom of dust cup is
correctly aligned, dust cup component can be directly pulled into main
body, and reliable assembly can be ensured after locking sound is
heard.
If dust cup is should be removed, dust cup release button should be
pressed, and the dust cup should be removed according to direction in
the drawing.
Installation and removal of dust cup component
When dust cup is installed, please firstly check whether internal parts
of dust cup component are installed completely or not. Missed
installation should be avoided. Please firstly align to clamp at the
bottom of dust cup during installation. After the bottom of dust cup is
correctly aligned, dust cup component can be directly pulled into main
body, and reliable assembly can be ensured after locking sound is
heard.
If dust cup is should be removed, dust cup release button should be
pressed, and the dust cup should be removed according to direction in
the drawing.
Fig. 4
How to Replace the Filter
• Remove the dust cup from the vacuum by
pressing the dust cup release button on top of
the dust cup (Fig. 1).
• Turn the filter cover to the left to the “Unlock”
position and lift off (Fig. 2).
• Remove the High Flow filter by grasping the top
of the filter and pulling straight up.
• Replace with a new filter or if desired you can
rinse the filter under warm water. Make sure the
filter is completely dry before placing it back into
the vacuum.
• Reattach the filter cover and turn to the right to
the “Lock” position (Fig. 3).
• Replace the dust cup into the vacuum (Fig. 4).
Fig. 1
Fig. 2
Fig. 3
lock
unlock

10
Cleaning the Dust Cup
• Remove the dust cup from the vacuum by
pressing the dust cup release button on top
of the dust cup (Fig. 1).
• Remove the filter assembly by pulling it up
and out of the dust cup (Fig. 2).
• Rinse the dust cup in warm water. Allow it
to dry thoroughly before reattaching it to the
vacuum.
• Replace the filter assembly by lining up the
notches on the filter and the dust cup and
pushing straight down.
• Replace the dust cup onto the vacuum body
and resume vacuuming.
Replacing the Microfiber Polishing
Pad
• Pull gently to remove the microfiber pad from
the bottom of the floor nozzle (Fig. 3).
• Wash frequently in warm water with mild
detergent or replace as needed.
• Press microfiber pad back into place on the
bottom of the floor nozzle.
Fig. 2Fig. 1
Maintenance and Care
Installation and removal of dust cup component
When dust cup is installed, please firstly check whether internal parts
of dust cup component are installed completely or not. Missed
installation should be avoided. Please firstly align to clamp at the
bottom of dust cup during installation. After the bottom of dust cup is
correctly aligned, dust cup component can be directly pulled into main
body, and reliable assembly can be ensured after locking sound is
heard.
If dust cup is should be removed, dust cup release button should be
pressed, and the dust cup should be removed according to direction in
the drawing.
Fig. 3

11
Problem Check Point Possible Solution
Suction power is weak. • Dust cup
• Floor nozzle
• Filter
• If the dust cup is full, empty it.
• If clogged, remove the object.
• Clean or replace filter.
The vacuum does not work. • Power cord Insert the power plug firmly into an electrical
outlet.
Sudden loss of power. • Thermal reset Turn off vacuum and unplug from electrical
outlet. Let vacuum cool down for 30 minutes
before turning back on. Check for clogs.
Empty dust container.
Dirt and debris are blowing
through exhaust vent.
• Filter Make sure the filter is clean, dry and
installed correctly.
All other service should be performed at a Fuller Brush service center.
1-866-539-2099
• Keep your vacuum clean and in good operating condition.
• Always use genuine replacement parts. Use of other products may result in poor cleaning
performance, potential vacuum cleaner damage and may void the vacuum warranty.
Genuine Fuller Brush products are designed for maximum cleaning performance.
• Store your vacuum carefully in a dry area.
• For optimum cleaning performance and safety, follow your owner’s manual instructions.
WARNING! To Reduce the Risk of Electrical Shock or Injury From Moving Parts, Unplug the
Vacuum Before Servicing.
CAUTION! To Reduce the Risk of Electric Shock, Do Not Handle the Appliance with Wet Hands.
Troubleshooting
For Best Performance

12
What Is Covered:
This warranty covers any defects in material and workmanship in your new Fuller
Brush vacuum.
How Long Coverage Lasts:
Warranty coverage for the Fuller Brush vacuum lasts one year. Household models used
commercially are warranted for 90 days.
What Is Not Covered:
• Damage to the vacuum which occurs from neglect, abuse, alterations, accident,
misuse or improper maintenance.
• Normal replacement items: disposable filters and microfiber polishing pads.
What Fuller Brush Will Do:
This warranty provides, at no cost to you, all labor and parts to keep this vacuum in
correct operating condition during the warranted period.
How to Get Service:
Warranty service can only be obtained by presenting the vacuum to the Fuller Brush
Service Center.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER WARRANTIES
WHETHER WRITTEN, ORAL, EXPRESSED OR IMPLIED, (INCLUDING ANY WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE). THIS WARRANTY
DISCLAIMS LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
How State Law Applies:
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
For customer support, please call
1-866-539-2099
Register your warranty online at www.FullerBrushVacuums.com
Warranty

14
Fuller Brush Vacuum Cleaners
PO Box 730
Fenton, MO 63026
www.FullerBrushVacuums.com
1-866-539-2099
©2016 Fuller Brush Vacuum Cleaners�
FBOM-BFM
10�16