Fulterer FR 3610 User manual

Supplied Parts List
ADrawer Slide, left (cabinet, middle and drawer profile with integrated ECD).
BDrawer Slide, right (cabinet, middle and drawer profile with integrated ECD).
CBottom Mount Brackets
D1 Connecting Bracket
D2 Connecting Bracket with slot
D3 Support profile, left
D4 Support profile, right
FTray (1 piece).
GWire Support (1piece).
Screws:
(g) M4 x 8mm, zinc
(h) M4 Nut, zinc
( i ) M4 x 8mm, zinc
( j ) No. 8 x 5/8 in., zinc
( n) Washer
FR 3610 Mounting Instructions
1 of 3
FR 3610
FR 3610
235 (9.25)
468 (18.43)
FR 3610: 375 – 475 (14.76 –18.75)
Inside cabinet width
mm (in.)mm (in.)
6
0
96
(3.78)
38
70
102
134
Adjustable
Door Front Bracket
facing inward
Adjustable
Door Front Bracket
facing outward
64 (2.52)
65 (2.56)
10
Min. inside cabinet depth
575 (22.64)
Inside cabinet width
375–475
(14.75 –18.75)
34L (36 qt.)
Waste Basket
34L (36 qt.)
Waste Basket
Figure 1

F
Tray
Adjustable door
front bracket
max.
424mm
(16.69in.)
Tray width
G
Wire Support
(n)
(i)
mm (in.)
Adjustable door
front bracket
F
Tray
min.
324mm
(12.76in.)
Tray width
FR 3610 Mounting Instructions
2 of 3
B
Cabinet Profile
Integrated ECD
(Easy-Close-Device)
A
Cabinet Profile
C
C
C
(g)
(h)
(h)
Back set
from front of cabinet
(g)
(h)
(h)
(j)
Step 1. Identify all parts. The build-in width of the unit is set to its maximum of 476mm (18.75 in.) with tray Fat 424mm
(16.69 in.). If you are faced with a narrower cabinet inside width you have the option of cutting tray Fdown to the required size
on a table saw. Be sure to cut away equal amounts from each side to a minimum tray width of 324mm (12.76 in.) and a
minimum build-in width of 375mm (14.76 in.). Make appropriate width adjustment to the connecting brackets
D1 and D2 (figure 2).
Step 2. Mount cabinet profiles Aand B to the floor of the cabinet with screws (j) (figure 1, 2 and 3). Make sure that slides
are parallel and perpendicular to the front edge. Determine the back set from the front edge of the cabinet by the thickness
of the bumpers on the door panel.
Figure 2

FR 3610 Mounting Instructions
3 of 3
D2
D1
B
Drawer Profile
A
Drawer Profile
FRONT
(g)
(g)
(g)
(g)
(i)
(i)
(i)
(h)
(h)
(k)
(h)
(g)
(g)
(g)
(g)
(g)
(g)
(j)
(j)
(j)
(j)
(j)
(j)
(g)
(g)
D1
D1 FR 3610
D2
D4
D2
D3
Figure 3
Step 3. Determine the location of the door front bracket using figure 1. Attach door with screws (j).
Adjust alignment screws (k).
1., 2., 3. and 3.1.
Position the ECD as illustrated flush with the end if the slide.
Be sure that all parts clip in their appropriate location.
ECD Assembly
1.
2.
3.
3.1.