Fulterer FR771 User manual

#126 08/6/07 H.S.
page 1 of 5
Mounting Instructions
FR771 Progressive-Action Full Extension, Bottom Mount
250 lbs. Capacity, with Matching Top Guide
(US Patent No. 6,199,966)
LGA tested according to DIN 4554
standard at 50.000 Double Cycles
http://www.fulterer.com
http://www.fultererusa.com

page 2 of 5
Mounting Instructions
Tee nuts M6 or 1/4”
39
25
56
– 107
min. 124
79.5
#8 screws
M6 or 1/4”-20
thru bolts
Adapter
2
37
2
x
0
37 99
291
419
451
483
515 547
(11x)
Cabinet Profile
Cabinet Profile
6.5
56
Front View
Front
Front
Front
2
37
39
0
B
1
1a
1b
Mounting
+ FR777 Progressive-Action Pantry-Pullout Cabinet Profile
mounts in cabinet as per drawing 1, 1a and according to the
hole locations 1b.
Important: Due to the high weight capacity and leverage created
when fully loaded, we highly recommend to thru-bolt the cabinet
profile at the last two holes (X) M6 thru bolts (DIN 931 or
7985A) and tee nuts are used. (or 1/4"-20 machine screws with T-nuts.)
It is also essential that the cabinet is securely mounted to the
wall (not only to the sheetrock, but to the stud frame work of the wall
to prevent tipping over.)
Hole Locations

page 3 of 5
Mounting Instructions
2
2
10
37
*
*
*
* use 4mm diameter (#6)
countersunk screws 192160
39.6
25
Front View
Front
Front
Front
Front
Front
(36.5 )
39
2
210
37192160
39
2
39 199
359 519
0
(4x)
Top Guide U-Profile
5
0
37
69
197
229
357
389
(3x) 12
(3x)
Ball-Bearing
Slide
6.5
( 6.5 )
210
#6 screws
37192160
+1
59 -1
+8
0
2
2a
A
3
Mounting
+ The Top Guide mounts as per drawing 2, 2a and according to hole locations.
+ The U-Profile of the Top Guide mounts as per drawing 3, 2a and according to the hole locations.
Hole Locations

page 4 of 5
Mounting Instructions
Mounting
+ The Adapter mounts as per drawing 4, 1a and according to the hole locations.
Mounting
+ The following adjustments should already be pre-adjusted:
Please check before inserting slide-out unit that the safety-clip on the
U-profile of the Top Guide is open (Illustration A) and the angle-
adjustment is all the way down (Illustration B).
+ Insert the slide-out unit all the way to the end stop.
+ Close safety-clip on the U-profile of the Top Guide (Illustration A).
+ Tighten the Allen Head set screws at the same time adjusting the side
to side position (Illustration B).
+ Adjust the angle position on the FR771 as per (Illustration B).
Important:
+ Do not lubricate any part of the slide at any time!
Options
+ Easy-close damping-system Order Number 000003401
consisting of (6200510, 8300015, 6200516, 8300001)
Hole Locations
Safety-clip
closed
open
Adapter
Allen Key 4mm
Vertical and horizontal
adjustments on the slide
in
L
out
inout
R
LR
RL
RL
up
down
side adjustment
Angle adjustment
Adapter mounting
+ side adjustment
2
39
137.5 439.5 459.5
199
359 519
0
(4x)
Adapter
8Machine Counter Sunk
Screw 1/4”-20
117.5
Front
4
A
A
B

page 5 of 5
Easy-Close 3401 for FR771 Mounting Instructions
http://www.fulterer.com
http://www.fultererusa.com
Caution:
Clip springs on the right side
Clip into place with piston in
closed position only, to avoid
bending the piston
6200516
8300015
6200510
8300001
Standard setup
adjust from
underneath with
4mm Allen Key
Adjustment range up / down ± 1.5mm
+1.5
1mm
-1.5
3
4
5
1
2
Assemble parts as illustrated 1, 2, 3, 4, 5.