Fulterer FR 771 User manual

(0904#126)
Mounting Instructions
FR 771 Progressive-Action Full-Extension
Heavy-Duty Drawerslide with Top Guide
(US-Patent No. 6,199,966)
www.fultererusa.com page 1 of 4
LGA tested according to DIN 4554
standard at 50.000 cycles
FLOOR
TOP
250
LBS
(per slide)
75
3
mm
in.
WSI MSSU 139-022

FR 771 Progressive-Action Full-Extension
Heavy-Duty Drawerslide with Top Guide
(US-Patent No. 6,199,966)
www.fultererusa.com page 2 of 4(0904#126)
1
3
24
96
56
2
75
108.2
2
2
35
0
Cabinet Profile
Adapter
2a
1a
4
2
192160 37
49+5
37.5
(x)
25
Cabinet Profile
Adapter
160160 37
WSI MSSU 139-022

Mounting Instructions
www.fultererusa.com page 3 of 4(0904#126)
;;
;;
;;
;
;;
;
A
B
For cabinets taller than 1800mm (72in.)
Up to 450mm (18in.) width one slide is recommended.
Over 450mm (18in.) width two slides are recommended.
Mounting
• The FR 771 Progressive-Action Pantry-Pullout Cabinet Profile
mounts in cabinets as per drawing 1, 1a and according to the
hole locations (page 4).
Important: Due to the high weight capacity and leverage created
when fully loaded, we highly recommend to thru-bolt the cabinet
profile at the last two holes (x) with M6 and/or 1/4"-20 machine
screws with T-nuts. It is also essential that the cabinet is securely
mounted to the wall (not only to sheetrock, but to the stud frame
work of the wall) to prevent tipping over.
• The Top Guide mounts as per drawing 2, 2a and according to the
hole locations (page 4).
• The U-profile of the Top Guide mounts as per drawing 4, 2a
and according to the hole locations (page 4).
• The Adapter mounts as per drawing 3, 1a and according to the
hole locations (page 4).
Installation
• The following adjustments should already be pre-adjusted:
Please check before inserting slide -out unit that the safety-clip
on the U-profile of the Top Guide is open (illustration A) and the
height adjustment is all the way down (illustration B).
Also check that the Allen Head setscrews are backed out far
enough (illustration B).
• Insert the slide-out unit all the way to the end stop.
• Close safety-clip on the U-profile of the Top Guide (illustration A).
• Tighten the Allen Head setscrews at same time adjusting the side
to side position (illustration B).
• Adjust the height position on the FR771 as per (illustration B).
Important
•Do not lubricate any part of the slide at any time.
Height adjustment
screw
Adapter set-screws
and side adjustment
Vertical and horizontal
adjustments on the slide
Safety Clip
Open
Closed
Width
Width
WSI MSSU 139-022

(0904#126) page 4 of 4
www.fultererusa.com
Hole Locations
FR 771 Progressive-Action Full-Extension
Heavy-Duty Drawerslide with Top Guide
(US-Patent No. 6,199,966)
547
(x)
515 583
Cabinet Profile and Adapter
451
56
419 291
Hole locations for cabinet profile = 575mm length
99 35 0
2
4
2
192160
Top Guide and U-Profile
37
49+5
37.5
Top Guide U-Profile
25
2
2
2
35
0
Cabinet Profile
Adapter
160160 37
WSI MSSU 139-022