Furinno 19154H User manual

19154H20210810
18
Recommended Maximum Weight
*Unit in Pound(lbs.)
WARNING:
>This unit has been designed to
support the maximum loads shown.
Exceeding these load limits could
cause sagging, instability, product
collapse, and/or serious injury.
>DO NOT allow children to climb on
unit.
> Put heavier items on lower shelves.
Assembly Instruction
Furinno Lucca Simple Design 3-Drawer Dresser
MODEL : 19154H
Customer Support
www.furinno.com
NEED HELP? For replacement requests or product inquiries,
please contact our Customer Service Team by emailing us at
[email protected]. Thank you for selecting Furinno!
20
Recomm. 2 Persons
Approx. 1.5 Hours
Wall stud
wallboard
STEP 11
STEP 12
15
WALL MOUTING SET
12
1 SET
TOOL REQUIRED
Tool RequiredTool Required
TOOL REQUIRED

2
EXPLODED VIEW
USEFUL HINTS BEFORE YOU START:
1. Read each step carefully before starting.
2. It is important that each step is performed in correct order to avoid difficulties.
3. Identify, soft and count the parts before assembly.
4. Assemble your furniture on packaging cardboard to prevent scratch or damage.
5. Clean the product with mild cleanser using soft damped cloth. Do not use harsh or abrasive cleanser.
6. Using incompatible hardware might cause damage to product.
EXPLODED VIEW
PARTS LIST
LEFT PANEL 1 PC
A
RIGHT PANEL 1 PC
B
HARDWARE LIST
DRAWER SLIDE
6
9
POWER PIN 18 PCS
BOTTOM PANEL 1 PC BOTTOM BACK PANEL 1 PC
E
DRAWER SIDE 6 PCS
G
L BRACKET 4 PCS
7
STEP 9
STEP 10
TOP PANEL 1 PC
C
DRAWER FRONT 3 PCS
F
DRAWER BACK 3 PCS
I
DRAWER BOTTOM 3 PCS
H
SUPPORT PANEL 1 PC
J
10
5
8
PAN HEAD SCREW 38 PCS
HANDLE SCREW 6 PCS
11
DRAWER BRACKET 6 PCS
3 SETS
4 10
FLAT HEAD SCREW 18 PCS DRADWER SLIDE 3 SETS
TOOL REQUIRED
D
UPPER BACK PANEL 1 PC
L
K
DRAWER SUPPORT 3 PCS
KICK PANEL 1 PC
M
F
E
A
B
C
DH
J
K
L
M
G
G
I
1
4
7
CAM BOLT 12 PCS
FLAT HEAD SCREW 36 PCS
DRIVE FASTENER 12 PCS
13
HANDLE 3 PCS
3
DOWEL 20 PCS
2
CAM LOCK 12 PCS
WALL MOUTING SET
12
1 SET
finished surface
x3
H
F
7
7
7
7
I
G
G
M
x3
F
H
8
13
I
G
G
x
F
G
I
M
4
4
4
4
4
4
8
HANDLE SCREW 6 PCS
DRIVE FASTENER 12 PCS
7
13
HANDLE 3 PCS
TOOL REQUIRED
TOOL REQUIRED
3
STEP 9.1 STEP 9.2
DR
DL
CR
CL
CL
CR
DR
DL
DL
DL
DL
DR
screw position
DR
DL

6
STEP 7
STEP 8
3
STEP 1
STEP 2
1
CAM BOLT 8 PCS CAM LOCK 4 PCS
24
FLAT HEAD SCREW 18 PCS
PAN HEAD SCREW 12 PCS
5TOOL REQUIRED
2
3
2
3
3
3
3
E
J
2
2
2
2
3
2
2
5
5
9
K
D
x3
M
3
3
finished edge
1
2
3
11
2
1
A
CL
10a
3
2
1
finished edge
11
1
2
B
10b
CR
bracket orienta onbracket orienta
x3
x3
5
5
5
5
11 11
GG
5
Please note, you will repeat this step for
each of the 3 drawers.
x3
F
5
5
5
MG
G
PAN HEAD SCREW 12 PCS
5
DRAWER BRACKET 6 PCS
11 TOOL REQUIRED
L BRACKET 4 PCS
3
DOWEL 18 PCS
CAM LOCK 8 PCS
2
5
PAN HEAD SCREW 8 PCS
9
TOOL REQUIRED
44
TOOL REQUIRED
3
DOWEL 2 PCS
CR
10
DRAWER SLIDE 3 SETS
CL
ARROW FACING OUTWARD
ARROW FACING OUTWARD
11
5
``CL ``
``CR
CR
``
CR

5
4
STEP 3
STEP 4
STEP 5
STEP 6
TOOL REQUIRED
finished edge
A
E
A
B
C
Assure that the unit is square.
Distance from corner to corner
must be equal as shown.
and/or serious injury.
Failure to do so could cause instability, product collapse,
All nails must be driven into the parts straight and centered.
Please make sure that the Back Panel is attached securely.

6
5
E
D
B
L
1
2
TURN 180°
TOOL REQUIRED
STEP 5.2
1
2
TURN 180°
TOOL REQUIRED
TURN 180°
TOOL REQUIRED
TOOL REQUIRED
5
PAN HEAD SCREW 6 PCS
6
POWER PIN 18 PCS
finished edge
A
J
E
D
K
1
2
TURN 180°
A
B
J
E
D
K
STEP 4.1
finished edge
STEP 4.2
1
1
1
1
finished edge
unfinished edge
STEP 5.1
C
1
CAM BOLT 4 PCS
TURN 90°