Furinno Turn-N-Tube 99603 User manual

Assembly Instruction
Customer Service
Tel/Fax: [phone]
Toll Free: 773.299.8111 (Mon - Fri 9am - 5pm)
Email: [email protected]
WARNING:
>This unit has been designed to support the
maximum loads shown. Exceeding these
load limits could cause sagging, instability,
product collapse, and/or serious injury.
>DO NOT allow children to climb on unit.
>Put heavier items on lower shelves.
its Space. its Budget
www.furinno.com
Recommended Maximum Weight
Furinno Turn-N-Tube 3-Tier
TV Entertainment Center
9960320140923
MODEL : 99603
38.6”(W) x 22.85”(H) x 13.4”(D)DIMENSION :
*Unit in Pound(lbs)
STEP 5
Slide Bottom Back Panel (E) into the grooves of
Long Engrove Tubes (3), as shown.
Attach Back Panel (C) to assembled section from
Step 5 using Legs (6) and No-Tip Feet (7).
STEP 6
3E
FINISHED
SURFACE
UNFINISHED
SURFACE
E
B
6 LEG - 2 PCS
7 NO -TIP FEET - 2 PCS
UNFINISH
SURFACE
7
C
6
6
7
50
30
30
Tool RequiredTool RequiredNo Tools Required
Recomm. 1 PersonRecomm. 2 Person
Approx. 5 minutesApprox. 10 minutesApprox. 15 minutesApprox. 20 minutesApprox. 30 minutes
All manuals and user guides at all-guides.com
all-guides.com

STEP 2
Attach Short Tube (2) and Short Engrove Tube (4)
to Insert Cap (5), as shown.
Attach Shelf Panel (B) to assembled from Step 3
using Long Tube (1) and Long Engrove Tube (3),
as shown.
STEP 4
Slide Upper Back Panel (D) into the grooves of
Short Engrove Tubes (4), as shown.
STEP 3
STEP 1
Press Insert Cap (5) into Top Panel (A), as shown.
A
UNFINISHED
SURFACE
5
5 5
5
5 INSERT CAP - 4 PCS
INSERT CAP INSERT
CAP
4 SHORT ENGROVE TUBE - 2 PCS
2 SHORT TUBE - 2 PCS
22
44
5
AUNFINISHED
SURFACE
4D
UNFINISHED
SURFACE
A
DFINISHED
SURFACE
3 LONG ENGROVE TUBE - 2 PCS
1 LONG TUBE - 2 PCS
11
33
UNFINISHED
SURFACE A
Using either a soft rubber mallet or by firmly
pressing the Insert Caps into the Top Panel
using the flat side of a book or other hard flat
surface to press the caps into the panel.
USEFUL HINTS BEFORE YOU START:
1. Read each step carefully before starting.
2. It is important that each step is performed in correct order to avoid difficulties.
3. Identify, sort and count the parts before assembly.
4. Assemble your furniture on packaging cardboard to prevent scratch or damage.
5. Clean the product with mild cleanser using soft damped cloth. Do not use harsh or abrasive cleanser.
6. Using uncompatible hardware might cause damage to product.
1
2
3
2pcs
2pcs
2pcs
A 1pcs
Top Panel
Long Engrove Tube
No Hardware List Qty No QtyParts List
Long Tube
Short Tube
4
5
6
2pcs
4pcs
2pcs
Leg
7 2pcs
No-Tip Feet
Short Engrove Tube
Insert Cap
B
C
1pcs
1pcs
Bottom Panel
Shelf Panel
D
E
1pcs
1pcs
Upper Back Panel
Bottom Back Panel
A
B
C
D
E
All manuals and user guides at all-guides.com