Furinno NT-13008 User manual

Assembly Instruction
Customer Service
Tel/Fax: [phone]
Toll Free: 773.299.8111 (Mon - Fri 9am - 5pm)
Email: [email protected]
WARNING:
>This unit has been designed to support the
maximum loads shown. Exceeding these
load limits could cause sagging, instability,
product collapse, and/or serious injury.
>DO NOT allow children to climb on unit.
>Put heavier items on lower shelves.
its Space. its Budget
www.furinno.com
Recommended Maximum Weight
Furinno Ubah No Tools Contemporary
Computer Desk
NT1300820140425
MODEL : NT-13008
43.5”(W) x 28.3”(H) x 19.8”(D)DIMENSION :
40
*Unit in Pound(lbs)
Attach Panel(D)to Panel(B)&(I).
Repeat the same method as
Step 6.
STEP 12
Attach Short Round Pole(6)to
Panel(A)and tighten it.
STEP 11
Attach Panel(A)to assembled unit.
Attach Short Round Pole(6)to Panel(E)
and Fix Mini Round Leg(5)to Panel(E)
and tighten it.
STEP 13
Slot in Door(10)to assembled unit,as shown.
STEP 14
Insert Plastic Stopper(7)into
pre-drilled holes of Panel(J).
STEP 10
(7)x8pcs
(5)x4pcs
Tool RequiredTool RequiredNo Tools Required
Recomm. 1 PersonRecomm. 2 Person
Approx. 5 minutesApprox. 40 minutesApprox. 15 minutesApprox. 30 minutes

STEP 9
Attach Panel(J)to assembled
unit and insert Plastic Pin &
Nut(8)into the pre-holes of
Panel(J).
Attach Panel(E)&(F)to assembled
unit.Repeat the same method as
Step 6.
STEP 8
unfinished
edge
Attach Panel(C)to Panel(B).
** 1)Turn on Cam-Lock and fix
into the pre-drilled nut.
2)Turn off Cam-Lock when
the panel were fixed.
STEP 6
Insert Dowel(1)into pre-holes
on Panel(B)(C)&(D).
STEP 3
unfinished
edge
Attach Panel(H)&(I)to Panel(G).
Repeat the same method as in
Step 6.
STEP 7
unfinished
edge
4.1 Insert Dowel(1)into the
pre-holes on Panel(G,H,I).
4.2 Insert Magnet(4)into the
pre-holes on Panel(I).
STEP 4
(4)x2pcs
(1)x12pcs
Insert Door Spring(7)into the
pre-drilled holes on Plastic
Door(10),as shown.
STEP 5
(7)x2pcs
Fix Insert Cap(3)into Panel(A).
STEP 2
(3)x4pcs
STEP 1
Fix Lock Switch(2)into the
Cam-Lock of every panels.
turn on turn off
slot in
Cam-Lock
(2)x22pcs
(1)x7pcs
unlocked
locked
4
1
2
3
21pcs
22pcs
4pcs
Insert Cap
No Hardware List Qty
Plastic Dowel(M6x20mm)
Lock Switch(12mm)
4
5
6
2pcs
4pcs
4pcs
Short Round Pole
Magnet
Mini Round Leg
7
8
7pcs
8pcs
Plastic Pin/Nut
Plastic Stopper
9
10
4pcs
2pcs
Door Spring
Plastic Door
A
1pcs
Top Panel
No Qty Parts List
B
C
1pcs
1pcs
Side Front Bar
Right Side Panel
D
E
F
1pcs
1pcs
1pcs
Bottom Panel
Back Bar
Small Top Panel
G
H
1pcs
1pcs
Left Side Panel
Shelf Panel
I
J
1pcs
1pcs
Back Panel
Center Panel
USEFUL HINTS BEFORE YOU START:
1. Read each step carefully before starting.
2. It is important that each step is performed in correct order to avoid difficulties.
3. Identify, sort and count the parts before assembly.
4. Assemble your furniture on packaging cardboard to prevent scratch or damage.
5. Clean the product with mild cleanser using soft damped cloth. Do not use harsh or abrasive cleanser.
6. Using uncompatible hardware might cause damage to product.
(I)