Furniture of America CM-BK600A User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 12
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Rev: 17-01-05
CM-BK600A
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]

Page 2 of 12
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

Parts List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 12
#1 x 2pcs
Lower HB/FB
#2 x 2pcs
#3 x 1pc
#4 x 1pc
#5 x 1pc
Lower Front Side Rail
#6 x 1pc
Lower Back Side Rail
#7 x 2Set (10pcs)
#8 x 1pc
Ladder
Twin Slat Kit
#9 x 2pcs
Front Panel
#10 x 2pcs
Side ( Left )
#11x 2pcs
Side ( Right )
#12 x 2pcs
Back Panel
#13 x 2pcs
Bottom Panel
#14 x 2pcs
Center Support
Upper HB/FB
Upper Back Side Rail
Upper Front Side Rail

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 4 of 12
Hardware List
#A x 16pcs
#B x 16pcs
#D x 4pcs
#F x 40pcs
#G x 20pcs
#C x 6pcs
Barrel Nut
Screw 3/16" x 1-3/16"
Bolt 1/4" x 1-9/16"
Screw 1/4" x 4"
Bolt 1/4" x 4"
#I x 1pc
Allen Wrench 4mm
Screw 3/16" x 1"
#E x 4pcs
Metal Dowel ɐ3/8" x 3-9/16"
Wood Dowel 1/4"x1-3/16"
#H x 8pcs

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 5 of 12
#12 #11
#10 #14
#13
#9
#12 #11
#10 #14
#13
#9
#1
#1
#2
#2
#4
#3
#5
#6
#8
#7
#7

#A x 8pcs
#B x 8pcs
Page 6 of 12
#A x 8pcs
#B x 8pcs
#D x 4pcs
#A
#B
#I
#1
#1
#4
#3
#A
#I
#B
#D
#2
#2
#6
#5
Insert barrel nuts (#B) to the holes of the side rails
(#3,4). Align side rails (#3,4) to the holes of the
lower HBs (#1), then secure with bolts (#A). Make
sure bolts (#A) connects to barrel nuts (#B).
Insert barrel nuts (#b) to the holes of the upper side rails (#5,6). Align
side rails (#5,6) to the holes of the upper HBs (#2), then secure with
bolts (#D). Make sure bolts (#D) connects to barrel nuts (#B).

#E x 4pcs
#C x 6pcs
Page 7 of 12
#E
#E
#E
#C
#I
#8
Insert metal dowels (#E) to the
holes of the lower HBs (#1). Align
the upper HBs (#2) to the holes
metal dowels (#E), then carefully
place onto it.
#3
#5
#6
#4
Align the ladder (#8) to the holes of the front side
rails, then secure with bolts (#C).

Page 8 of 12
#H x 4pcs
#11 #H
#F x 40pcs
#7
#7
#9
#F
#F
x 2
#10
Align twin slat kits (#7) to the bunk bed side rails.
Secure with screws (#F).
Insert wood dowels (#H) to the holes of the front panel
(#9). Align the left and right side panel (#10,11) to the
wood dowels (#H) attached to front panel (#9).

#13
Page 9 of 12
#G
#G x 4pcs
x 2
x 2
#10
#11
#9
#10
#11
#9
Secure the side panels (#10,11) with
screws (#G). There will be no pre-
drilled holes for screws (#G).
Slide bottom panel (#13) through the little linear gaps of the panels (#9,10,11).

#13
#12
#14
#G x 2pcs
#G x 4pcs
#G
#G
#G
x 2
x 2
Page 10 of 12
Align the linear gaps of the back panel (#12) to bottom
panel (#13), then secure with screws (#G).
Align center support (#14) to the holes of the front and
back panel (#9,12). Secure with screws (#G).