Furniture of America CM-TR453 User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 6
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Rev: 18-03-12
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
CM-TR453
For more information contact our team: [email protected]

Page 2 of 6
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

Parts List
#1 x 1pc
#2 x 1pc
#4 x 8pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
#3 x 2pcs
Page 3 of 6
Front Panel
#A x 8pcs
Bolt Ø1/4" x 1-3/8"
#B x 8pcs
Hardware List
#D x 8pcs
Screw #4 x 20mm
#5 x 2pcs
#7 x 2pcs
#6 x 1pc
Bottom Board
Washers Ø1/4"
#C x 16pcs
Screw #4 x 30mm
#E x 4pcs
Wheel
#F x 1pc
Allen Wrench 4mm
Back Panel
Left/Right Side Panel
Slats
Board Stand
Bottom Board

Page 4 of 6
#1
#2
#3
#7
#3
#5
#6
#5
#7
#4
Exploded View
#D
#E
#1
#2
#D x 8pcs
#E x 4pcs
Align wheels (#E) to the bottom o the front and back panels (#1,2).
Secure by using screws (#D). There will be no pre-drilled holes.

Page 5 of 6
#B x 8pcs
#A x 8pcs
#1
#2
#B
#A
#F
#C
#4
#C x 16pcs
#3
#3
#1
#2
Align the side panels (#3) to the front and back panels (#1,2), then secure
by using bolts (#A) with washers (#B).
Align slats (#4) to the front and back panels (#1,2), then secure by
using screws (#C). There will be no pre-drilled holes.

Page 6 of 6
#5
#5
#6
#7
#7
#1
#2
Place the bottom boards (#5,6) onto the trundle.
Slide board stands (#7) through the grooves of the trundle.