Furniture of America CM3149SC-2PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-08-14
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
CM3149SC-2PK

Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
Toll-Free 1-888-980-5122 or 1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 6

Page 3 of 6

Parts List Hardware List
#1 x 2 pcs x 2
Front Leg
#2 x 1 pc x 2
Backrest w/ Legs
#3 x 1 pc x 2
Seat
#A x 2 pcs x 2
Bolt 5/16”x1-1/2”
#B x 4 pcs x 2
Bolt 5/16”x2-1/2”
Before you begin, please read Page 3
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 4 pcs x 2
Bolt 5/16”x3”
MD
#D x 10 pcs x 2
Lock Washer
Page 4 of 6
#E x 10 pcs x 2
Flat Washer
#F x 1 pc
Allen Wrench
Note: The above parts and hardware are shown for
a complete assembly of ONE chair. However, the
actual parts and hardware (with an exception of the
Allen wrench) in the box will be twice the quantities
listed to include the assembly of the second chair.
X 2

I. Place the backrest with legs (#2)
on a protected surface. Align
the seat (#3) with the pre-drilled
holes of the backrest with legs
(#2).
II. Prepare 2 bolt assemblies by
inserting FIRST the lock washer
(#D) onto the bolt (#A) and then
the flat washer (#E) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assemblies
through the pre-drilled holes near
the center of the seat (#2) and
secure those bolts using the
Allen wrench (#F) to lock them
with the backrest with legs (#2).
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
Page 5 of 6
#B x 4 pcs
#D x 4 pcs
#E x 4 pcs
#A x 2 pcs
#D x 2 pcs
#E x 2 pcs
I. Place the seat (#3) facing down on
a protected surface. Align the two
front legs (#1) with the pre-drilled
holes on the corners of the seat
(#3).
II. Prepare 4 bolt assemblies by
inserting FIRST the lock washer
(#D) onto the bolt (#B) and then the
flat washer (#E) onto the SAME bolt
(#B), in that order.
III. Insert the bolt assemblies through
the corner holes of the seat (#3) and
secure those bolts using the Allen
wrench (#F) to lock them with the
front legs (#1).
#3

Turn right (clockwise) to tighten
Page 6 of 6
#C x 4 pcs
#D x 4 pcs
#E x 4 pcs
I. Prepare 4 bolt assemblies by
inserting FIRST the lock washer
(#D) onto the bolt (#C) and then
the flat washer (#E) onto the
SAME bolt (#C), in that order.
II. Insert the bolt assemblies
through the pre-drilled holes in
the corners of the seat (#3) and
secure those bolts using the
Allen wrench (#F) to lock them in
with the backrest with legs (#2).
ASSEMBLE EVERYTHING EXACTLY THE SAME FOR THE SECOND CHAIR
Carefully place the completed chair upright.
Make sure the chair is rested on a flat surface
and does not feel loose or wobbly. If it does,
double check that the bolts are secured and
properly tightened.
#2
#3