Furniture of America Lodia CM4825-C User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM4825-C
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-12-01
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
Hex Wrench
(Included)
2 PERSONS RECOMMENDED

Page 2 of 5

Parts List
#1 x 1 pc
Glass Top
#2 x 1 pc
Pedestal
#3 x 1 pc
Base
#D x 1 pc
Allen Wrench
#E x 6 pcs
Leveler
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#F x 1 pc
Hex Wrench
MD
#G x 2 pcs
Hex Nut
Page 3 of 5
#H x 2 pcs
Large Flat Washer
#I x 2 pcs
Cover
Hardware List (Continued)
Hardware List
#A x 4 pcs
Bolt 1/4”x1-1/2”
#B x 2 pcs
Threaded Stud
#C x 4 pcs
Small Flat Washer
Due to the size and/or weight of this
product, it is highly recommended that the
assembly should be done near the area of
its intended location. Make sure you have
enough space to move around during the
assembly.ALWAYS have at least two
people to help with transporting and
assembling the product to avoid any
potential injury and/or damage.

Turn right (clockwise) to tighten
Page 4 of 5
#B x 2 pcs
#G x 2 pcs
#H x 2 pcs
I. Carefully place the glass top (#1) facing down on a protected
surface. Insert the 2 threaded studs (#B) into the pre-drilled
holes on the center of the glass top (#1).
II. Place the pedestal (#2) over the 2 threaded studs (#B). Then
place 2 large flat washers (#H) over the 2 threaded studs (#B).
III. Secure the 2 hex nuts (#G) onto the same threaded studs using
the hex wrench (#F) to tighten the parts together.
#A x 4 pcs
#C x 4 pcs
#E x 6 pcs
I. Align the base (#3) with the
pre-drilled holes on the other
side of the pedestal (#2).
II. Prepare 4 bolt assemblies by
inserting the small flat
washer (#C) onto the bolt
(#A).
III. Insert the bolt assemblies
through pre-drilled holes of
the base (#3) using theAllen
wrench (#D) to lock them
with the pedestal (#2).
IV. Align the threaded ends of
the 6 levelers (#E) with the
pre-drilled holes on the base
(#3) and tighten by hand
until secured.
Turn right (clockwise) to tighten
Adjust the levelers according
to the ground level on Step 4.

Page 5 of 5
Insert the 2 covers (#I) over the 2 hex nuts (#G) secured to
the pedestal (#2).
#I x 2 pcs
ASSEMBLY IS COMPLETED
I. Carefully place the table in its
upright position. Make sure the
table is rested on a flat surface
and does not feel loose or
wobbly. If it does, double check
that the bolts/screws are
secured and properly tightened.
II. If necessary, adjust the levelers
(#E) according to the ground
level. To lower or to raise the
levelers (#E), turn the levelers
clockwise or counterclockwise,
respectively.