Furniture of America CM3418T User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM3418T
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Rev: 16-07-18

Page 2 of 5

Parts List
#1 x 1 pc
Table Top
#2 x 1 pc
Leaf
#3 x 2 pcs
Pedestal
#A x 24 pcs
Bolt 5/16”x1-3/4”
Before you begin, please read Page 3
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
MD
Page 3 of 5
Hardware List
#D x 1 pc
Allen Wrench
#C x 24 pcs
Lock Washer
#B x 24 pcs
Flat Washer
#4 x 2 pcs
Pedestal Base
#5 x 2 pcs
Table Base
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around during
the assembly. ALWAYS have at least two people to
help with transporting and assembling the product to
avoid any potential injury and/or damage.

Page 4 of 5
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
I. Align the table base (#5) with the
pre-drilled holes on the other end
of the pedestal (#3).
II. Prepare 4 bolt assemblies by
inserting FIRST the lock washer
(#C) onto the bolt (#A) and then
the flat washer (#B) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assemblies through
the pre-drilled holes on the table
base (#5) and secure those bolts
using the Allen wrench (#D) to
lock them with the pedestal (#3).
IV. Repeat the process above to
assemble the other table base
(#5) onto the other pedestal (#3).
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
I. Align the pedestal base (#4) with the
pre-drilled holes on the pedestal
(#3).
II. Prepare 4 bolt assemblies by
inserting FIRST the lock washer (#C)
onto the bolt (#A) and then the flat
washer (#B) onto the SAME bolt
(#A), in that order.
III. Insert the bolt assemblies through
the pre-drilled holes on the pedestal
base (#4) and secure those bolts
using the Allen wrench (#D) to lock
them with the pedestal (#3).
IV. Repeat the process above to
assemble the other pedestal base
(#4) onto the pedestal (#3)

Page 5 of 5
Turn right (clockwise) to tighten
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
#5 #5
I. With the help of another person,
carefully place the table top (#1) facing
down on a protected surface.
II. Align the assembled table base (#5)
with the pre-drilled holes on the bottom
of the table top (#1)
III. Prepare 4 bolt assemblies by inserting
FIRST the lock washer (#C) onto the
bolt (#A) and then the flat washer (#B)
onto the SAME bolt (#A), in that order.
IV. Insert the bolt assemblies through the
pre-drilled holes of the table base (#5)
and secure those bolts using the Allen
wrench (#D) to lock them with the table
top (#1).
V. Repeat the process above to assemble
the other assembled table base (#5)
onto the table top (#1).
VI. Carefully turn the completed table
upright. Make sure the table is rested
on a flat surface and does not feel
loose or wobbly. If it does, double
check that the bolts/screws are
secured and properly tightened.
I. To insert the table leaf (#2) unlock the
latches located under the table top
(#1).
II. Once unlocked, slide outward on both
ends of the outer-piece table until
there is sufficient opening to place the
table leaf (#2). Then slide inward on
both ends of the outer-piece table
until they are touching and sitting
flush with the table leaf (#2).
III. Secure the parts together by locking
the latches located under the table
top (#1).
ASSEMBLY IS COMPLETED
Adjust the leveler according to the ground level.
To lower or to raise the leg, turn the leveler
clockwise or counterclockwise, respectively.