Furniture of America CM4321C User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-06-10
Page 1 of 8
DIFFICULT
ASSEMBLY RATING
CM4321C
Phillips Screwdriver
(Not Included)
2 PERSONS RECOMMENDED

Page 2 of 8

Parts List Hardware List
#1 x 1 pc
Table Top
#2 x 1 pc
Leg A
#3 x 1 pc
Leg B
#A x 12 pcs
Bolt 5/16”x7/8”
#B x 8 pcs
Flat Bolt 5/16”x7/8”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 12 pcs
Lock Washer
MD
#D x 12 pcs
Flat Washer
#4 x 1 pc
Glass Top
Page 3 of 8
#E x 1 pc
Allen Wrench
#F x 1 pc
4-Way Bracket
#G x 4 pcs
Bracket

Align the two brackets (#G) with the pre-drilled
holes of the leg A (#2). Insert 4 bolts (#B) into the
brackets (#G) using theAllen wrench (#E) to lock
them with the leg A (#2).
Turn right (clockwise) to tighten
Page 4 of 8
#B x 4 pcs
#G x 2 pcs
Turn right (clockwise) to tighten
Align the two brackets (#G) with the pre-drilled holes
of the leg B (#3). Insert 4 bolts (#B) into the
brackets (#G) using theAllen wrench (#E) to lock
them in with the leg B (#3).
#B x 4 pcs
#G x 2 pcs

I. Carefully place the table top (#1) facing down on a protected surface.
II. Align the brackets (#G) assembled on the leg A (#2) AND the leg B (#3)
with the pre-drilled holes on the bottom of the table top (#1).
III. Prepare 8 bolt assemblies by inserting FIRST the lock washer (#C) onto
the bolt (#A) and then the flat washer (#D) onto the SAME bolt (#A), in that
order.
IV. Insert the bolt assemblies through the pre-drilled holes on the brackets
(#G) and secure those bolts using the Allen wrench (#E) to lock them with
the table top (#1).
V. Align the 4-way bracket (#F) onto the center of the leg A (#2) and the leg B
(#3).
VI. Prepare 4 bolt assemblies by inserting FIRST the lock washer (#C) onto
the bolt (#A) and then the flat washer (#D) onto the SAME bolt (#A), in that
order.
VII. Insert the bolt assemblies through the pre-drilled holes on the 4-way
bracket (#F) and secure those bolts using the Allen wrench (#E) to lock
them with the leg A (#2) AND the leg B (#3).
VIII. Carefully turn the table upright. Place the glass top (#4) onto the table top
(#1). Make sure the table is rested on a flat surface and it does not feel
loose or wobbly. If it does, double check that the bolts/screws are secured
and properly tighten.
Page 5 of 8
Turn right (clockwise) to tighten
#A x 12 pcs
#C x 12 pcs
#D x 12 pcs
#F x 1 pc
ASSEMBLY IS COMPLETED
#1

Parts List Hardware List
#1 x 1 pc x 4
Seat Cushion
#2 x 1 pc x 4
Seat Frame
#3 x 1 pc x 4
Base
#A x 6 pcs x 4
Bolt 5/16”x1-3/4”
#B x 6 pcs x 4
Lock Washer
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 6 pcs x 4
Flat Washer
MD
#D x 1 pc
Allen Wrench
#4 x 1 pc x 4
Center Leg
Page 6 of 8
#E x 4 pcs x 4
Screw
#5 x 2 pcs x 4
Side Leg
X 4
Note: The above parts and hardware are shown for a complete assembly
of ONE chair. However, the actual parts and hardware (with an exception
of the Allen wrench) in the box will be four times the quantities listed to
include the assembly of the second, third and fourth chairs.

Turn right (clockwise) to tighten
Page 7 of 8
#A x 3 pcs
#B x 3 pcs
#C x 3 pcs
Turn right (clockwise) to tighten
Align the seat cushion (#1) onto the top of the seat
frame (#2). Tighten 4 screws (#E) through the bottom of
the seat frame (#2) using the Phillips screwdriver to
secure them with the seat cushion (#1).
#E x 4 pcs
I. Insert the center leg (#4) and
the two side legs (#5) into the
seat frame (#2).
II. Prepare 3 bolt assemblies by
inserting FIRST the lock washer
(#B) onto the bolt (#A) and then
the flat washer (#C) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assemblies
through the pre-drilled holes on
the seat frame (#2) and secure
those bolts using the Allen
wrench (#D) to lock them with
the center leg (#4) and the two
side legs (#5).
#2

I. Insert the assembled center leg (#4) and
the side legs (#5) into the base (#3).
II. Prepare 3 bolt assemblies by inserting
FIRST the lock washer (#B) onto the bolt
(#A) and then the flat washer (#C) onto
the SAME bolt (#A), in that order.
III. Insert the bolt assemblies through the
pre-drilled holes on the base (#3) and
secure those bolts using the Allen
wrench (#D) to lock them with the
assembled center leg (#4) and the side
legs (#5).
IV. Make sure the chair is rested on a flat
surface and it does not feel loose or
wobbly. If it does, double check that the
bolts/screws are secured and properly
tighten.
Page 8 of 8
Turn right (clockwise) to tighten
#A x 3 pcs
#B x 3 pcs
#C x 3 pcs
ASSEMBLE EVERYTHING EXACTLY THE SAME FOR THE OTHER THREE CHAIRS.