Furniture of America YNJ-1449 User manual

E-commerce-Enitial Lab
ASSEMBLY RATING
The Assembly Rating is a 5-point
system that shows the degree of effort
needed in assembling a specific
product (with 1 being easy and 5 being
difficult). For most products, two
persons are recommended.
EASY DIFFICULT
Page 1 of 12
Tools Required for Assembly
Phillips Screwdriver
Allen Wrench
(Not Included)
( Included)
2 PERSON RECOMMENDED
ASSEMBLY INSTRUCTIONS
14.11.21
YNJ-1449
Hammer
(Not Included)

Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
Toll-Free 1-888-980-5122 or 1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 12

Page 3 of 12

Unless you are particularly adept at assembling flat-pack/knock-down
furniture, we understand building ready-to-assemble furniture can be a
frustrating experience for some. To help avoid confusion and to make
the assembly process quicker and smoother, we have provided some
helpful tips. Before you begin the assembly, please read the following:
1. Due to the size and/or weight on most of the ready-to-assemble furniture, it is
highly recommended that the assembly should be done near the area of its
intended location. Make sure you have enough space to move around during
the assembly. ALWAYS have at least two people to help with transporting and
assembling of the product to avoid any potential injury and/or damage.
2. To protect from damage, assemble the item on a clean, protective surface,
such as on a carpet or cardboard.
3. Make sure you have taken all the parts and hardware out of their packaging.
Do not throw away packaging material until assembly is completed.
4. Make sure all parts and hardware are accounted for by comparing the actual
parts and hardware to the list provided in the assembly instructions. Also
check for any irregularity such as crack, flaw or improperly drilled hole. If there
is any problem or missing piece, please contact the manufacturer or the
supplier. Please have the model number, part number and a brief description
of the problem ready will help expedite the replacement process.
5. Read the entire instruction manual and view the diagrams first before
assembling. Arrange your parts in order of use and group the identical
hardware together to make it easier to grab each piece as you begin to
assemble.
6. During the assembly process, make sure all parts are properly aligned before
tightening with the tool provided or required for the assembly. Do not use
power tools and do not over tighten.
7. When applying glue to the wood dowels to bond the parts together, please be
ABSOLUTELY certain that the parts are correct and lined up with each other
(refer to diagrams and take notice of the various pre-drilled hole locations).
When in doubt, assemble the parts together first and if the parts fit right, then
apply glue to the wood dowels.
PRE-ASSEMBLY INTRODUCTION
Page 4 of 12

CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS
ly
Page 5 of 12

HARDWARE LIST
Please keep for future reference
MODEL # YNJ-1449
PARTS LIST
122PCS 6 7
22PCS
4PCS
4PCS 8PCS
58PCS 48PCS
COFFEE TABLE
ASSEMBLY INSTRUCTIONS
8PCS
8
25 3
47.24" (W) X23.62" (D) X17.71" (H)
DIMENSIONS
10 11
2PCS
94PCS 4PCS
Before you begin, please
read "Assembly and
Care Advice","Pre-
Assembly Introduction"
and "Cam Lock Fastener
Assembly Instructions"
Page 6 of 12
2PCS
G
A
2PCS
C1PC
D1PC
E1PC
F2PCS
H1PC
2PCS
I1PC
J1PC
K1PC
L2PCS
2PCS
2PCS
1PC
2PCS
M
P
2PCS
N
Q
R
S
2PCS
O
B
17.71"
47.24"
23.62"
12 13 14
4PCS 1PC 4PCS
A
B
D
I
H
F
G
L

ASSEMBLY INSTRUCTIONS
Page 7 of 12
STEP1
Assembling Drawer’s Runners (a.k.a. Rails, Glides, Slides or Guides)
An assembly of ONE drawer requires two sets of runners. The runner is
composed of an inner rail and outer slide. Please read completely first before
assembling.
Mounting the Inner Rail (Fixed) of the Runner:
Before mounting, please determine which side of the panel is the front and rear.
The single screw hole on the outer slide MUST be positioned on the FRONT of
the panel. Place the inner rail of the runner in its correct position and flat on its
back. Slide the outer slide out to the way to align the center or second holes on
both ends of the inner rail with the pre-drilled holes on the panel. For most
applications, the center or second holes are used but if not, just make sure the
appropriate rail holes are aligned up with the panel holes. Use two screws to
secure the inner rail of the runner onto the panel.
Mounting the Outer Slide (Moveable) of the Runner:
Each outer rail is secured with a single screw onto the FRONT SIDE of the
drawer. Extend the two outer slides of the runners and place the drawer in
between those two outer slides. Align the pre-drilled holes on each side of the
drawer with the screw holes of the outer slides. Use two screws to secure from
the inside of the drawer into the screw holes of the outer slides.
front
front
Screw Hole
Screw Hole
7
7
2nd Hole
7
7
2nd Hole
6
6
6
P
Q
6
Hardware #7=8pcs
Hardware #6=4 runners
X2
X2

Page 8 of 12
ASSEMBLY INSTRUCTIONS
Hardware #1=14pcs
Hardware #3=10pcs
STEP2
A
1
C
1
D
BX2
3
E
3
14
3

Page 9 of 12
ASSEMBLY INSTRUCTIONS
F
1
GX2
X2
H
I
K
J
3
14
Hardware #1=4pcs
STEP3
Hardware #3=28pcs
3

Page 10 of 12
ASSEMBLY INSTRUCTIONS
Hardware #3=20pcs
Hardware #4=8pcs
Hardware #11=4pcs
Hardware #1=4pcs
Hardware #2=4pcs
Hardware #10=2pcs
STEP4
M
X2
L
X2
13
14
PQ
N
X2
X2X2
B
B
I
H
J
K
R
L
M
N
O
11
10
X2
4
2