Furniture of America CM4559S User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-10-29
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
CM4559S
2 PERSONS RECOMMENDED

Page 2 of 6

Parts List Hardware List
#1 x 1 pc
Table Top
#2 x 4 pcs
Leg
#3 x 1 pc
Shelf
#A x 4 pcs
Flat Bolt 5/16”x7/8”
#B x 8 pcs
Bolt 5/16”x7/8”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 4 pcs
Bolt 5/16”x1-3/4”
MD
#D x 12 pcs
Flat Washer
#4 x 1 pc
Glass Top
Page 3 of 6
#E x 12 pcs
Lock Washer
#F x 1 pc
Allen Wrench
#G x 4 pcs
Bracket
Due to the size and/or weight of this product, it is highly recommended that the
assembly should be done near the area of its intended location. Make sure you have
enough space to move around during the assembly. ALWAYS have at least two people
to help with transporting and assembling the product to avoid any potential injury and/or
damage.

Page 4 of 6
I. Align the shelf (#3) with the 4
legs (#2).
II. Prepare 4 bolt assemblies by
inserting FIRST the lock
washer (#E) onto the bolt
(#C) and then the flat washer
(#D) onto the SAME bolt
(#C), in that order.
III. Insert the bolt assemblies
through the shelf (#3) using
the Allen wrench (#F) to lock
them with the 4 legs (#2).
#A x 4 pcs
#G x 4 pcs
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
I. Align the bracket (#G) with the pre-drilled hole on
the leg (#2).
II. Insert a screw (#A) through the bracket (#G) using
the Allen wrench (#F) to lock them with the leg
(#2).
III. Repeat the process above to assemble the
remaining 3 brackets (#G) onto the remaining 3
legs (#2).
#C x 4 pcs
#D x 4 pcs
#E x 4 pcs
X 4

.
Turn right (clockwise) to tighten
Page 5 of 6
#B x 8 pcs
#D x 8 pcs
#E x 8 pcs
I. With the help of another person,
carefully place the table top (#1)
facing down on a protected
surface.Align the assembled
brackets (#G) on the legs (#2) with
the pre-drilled holes on the table
top (#1).
II. Prepare 8 bolt assemblies by
inserting FIRST the lock washer
(#E) onto the bolt (#B) and then
the flat washer (#D) onto the
SAME bolt (#B), in that order.
III. Insert the bolt assemblies through
the brackets (#G) and secure
those bolts using the Allen wrench
(#F) to lock them with the table top
(#1).
Place the table on the upright position. Carefully place the glass top
(#4) onto the table top (#1). Make sure the table is rested on a flat
surface and does not feel loose or wobbly. If it does, double check
that the bolts/screws are secured and properly tightened.

Page 6 of 6
ASSEMBLY IS COMPLETED
To install the batteries (not included), remove the screw that holds
the battery cover using a Phillips screwdriver. Install new AA-size
1.5-volt alkaline batteries with correct polarity (+,-) following the
illustration inside the battery cover. Close the battery cover and
tighten back the screw. The on-off switch near the battery
compartment will operate the LED lights.
Caution:
Use only batteries of the same type.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
Do not use rechargeable batteries.
Do not try to recharge non-rechargeable batteries.
Remove exhausted or corroded batteries.
Remove batteries to extend their life and to prevent corrosion if the light is not used for longer
than 2 weeks.