Furniture of America CM4320-3PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM4320-3PK
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-03-27
Page 1 of 6
DIFFICULT
ASSEMBLY RATING

Page 2 of 6

Parts List
#1 x 1 pc
Table Top
#2 x 4 pcs
Leg
#A x 8 pcs
Flat Washer
#B x 8 pcs
Lock Washer
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 8 pcs
Bolt 5/16”x2-1/4”
MD
Page 3 of 6
#D x 1 pc
Allen Wrench
Hardware List

I. Carefully place the table top (#1) facing down on a protected surface. Align
the leg (#2) with the pre-drilled holes on the bottom of the table top (#1).
II. Prepare two bolt assemblies by inserting FIRST the lock washer (#B) onto
the bolt (#C) and then the flat washer (#A) onto the SAME bolt (#C), in that
order.
III. Insert the bolt assemblies through the two pre-drilled holes on the bottom of
the table top (#1) and secure those bolts using the Allen wrench (#D) to lock
them in with the leg (#2).
IV. Repeat the process for the remaining 3 legs (#2).
Turn right (clockwise) to tighten
Page 4 of 6
Enlarged
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
ASSEMBLY IS COMPLETED
Carefully turn the completed table upright. Make sure the table is
rested on a flat surface and it does not feel loose or wobbly. If it
does, double check that the bolts are secured and properly tighten.

Parts List
#1 x 1 pc x 2
Table Top
#2 x 4 pcs x 2
Leg
#A x 8 pcs x 2
Flat Washer
#B x 8 pcs x 2
Lock Washer
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 8 pcs x 2
Bolt 5/16”x2-1/4”
MD
Page 5 of 6
#D x 1 pc
Allen Wrench
Hardware List
Note: The above parts and hardware are shown for a
complete assembly of ONE end table. However, the
actual parts and hardware (with an exception of the
Allen wrench) in the box will be twice the quantities due
to the packaging of TWO end tables in a box.
X 2

I. Carefully place the table top (#1) facing down on a protected surface. Align
the leg (#2) with the pre-drilled holes on the bottom of the table top (#1).
II. Prepare two bolt assemblies by inserting FIRST the lock washer (#B) onto
the bolt (#C) and then the flat washer (#A) onto the SAME bolt (#C), in that
order.
III. Insert the bolt assemblies through the two pre-drilled holes on the bottom of
the table top (#1) and secure those bolts using the Allen wrench (#D) to lock
them in with the leg (#2).
IV. Repeat the process for the remaining 3 legs (#2).
Turn right (clockwise) to tighten
Page 6 of 6
Enlarged
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
ASSEMBLY IS COMPLETED
Carefully turn the completed table upright. Make sure the table is
rested on a flat surface and it does not feel loose or wobbly. If it
does, double check that the bolts are secured and properly tighten.
ASSEMBLE EVERYTHING EXACTLY THE
SAME FOR THE SECOND END TABLE