Furniture of America CM7298Q/F User manual

Page 1 of 7
Assembly Instructions
EASY DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Tools Required For Assembly:
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7298Q/F
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
Rev: 19-01-14
For more information contact our team: [email protected]

Page 2 of 7
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 7
#2 x 2pcs
Leg Headboard (L&R)
#1 x 1pc
Headboard
Parts List Hardware List
#B x 6pcs
Flat Washer Ø5/16"
#A x 6pcs
Bolt Ø5/16" x 1-3/8"
#3 x 1pc
Storage Footboard
#5 x 1pc
Center Rail
#7 x 3pcs Ø5/16"
Support Leg 200x30x30mm
#4 x 2pcs
Side Rails
#6 x 1set
Slat (9pcs)
#C x 21pcs
Screw #4 x 35mm
#D x 4pcs
Screw #4 x 25mm
#E x 4pcs
Metal Dowel Ø1/4'' x 2''
#F x 1pc
Allen Key M4
#G x 6pcs
Lock Washer Ø5/16"

Page 4 of 7
Exploded View
#E x 4pcs
#1
#1
#2L
#3
#4
#5
#6
#7
#2R
#4
#2L
#2R
#E
Insert 2 metal dowels (#E) into the holes along the bottom of each end of
the headboard (#1), then apply the legs (#2) onto those metal dowels (#E).

Page 5 of 7
#A x 6pcs
#B x 6pcs
#G x 6pcs
#A
#B
#G
#F
#D x 4pcs
#D
#1
#1
#2L
#2R
#2L
#2R
1. Prepare 6 bolt assemblies by inserting
washer (#B,#G) onto the bolt (#A).
2. Insert 3 bolt assemblies into
each leg (#2), then secure
using the Allen wrench (#F).
Insert 2 screws (#D) into the holes
along the inner side of the legs (#2),
then secure using a screwdriver.

Page 6 of 7
#4
#4
#1
#3
#5
#7 Leveler
Hook each end of the side rails (#4) onto the slots
along the headboard (#1) and footboard (#3).
Insert the threaded end of the center
support legs (#7) into the holes along
the center rail (#5). Turn right tighten.
Adjust leveler according
to ground level.

Page 7 of 7
#C x 18pcs
#C x 3pcs
#C
#4
#4
#6
#C
#6
#5
Place the slats (#6) onto the side rails
(#4), then insert a screw (#C) into each
end. Secure using a Phillips screwdriver.
Insert a total of 3 screws (#C)
into the center of the slats (#6).