Furniture of America CM7315CK User manual

AssemblyInstructions
EASY DIFFICULT
Page 1 of8
ASSEMBLYRATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product(with 1 being
easy and 5 being difficult).For some
products,two persons are recommended.
CM7315CK
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
Wrench
(Included)
(Not Included)
Rev: 18-04-20
For more information contact our team: [email protected]

Page2 of 8
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches.Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED

Parts List
Hardware List
#1 x 1pc
#2 x 2pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
HeadboardPanel
#3 x 1pc
#6 x 1set
#7 x 2pcs
#5 x 1pc
Page3 of 8
#4 x 2pcs
Headboard Leg (L&R)
Footboard
Side Rail
Bed Slat 13pcs
Headboard Support
Support Leg 28 x 28 x 170mm
#E x 15pcs
#B x 12pcs
#C x 12pcs
Lock Washer Ø5/16"
Flat Washer
Ø5/16"
#D x 1pc
#F x 8pcs
#G x 8pcs
#H x 1pc
Screw #4 x 30mm
Allen Key 4mm
Threaded Pins Ø5/16" x 3-1/2"
Hex Nut Ø5/16"
Wrench 14mm
#A x 12pcs
Bolt Ø5/16" x 2"
Ø1/4
#8 x 5pcs
Support Leg 28 x28 x 390mm
Ø1/4

#9 x 1pc
Slat Center Support
#10 x 2pcs
Top Bed Rail
#L x 12pcs
#M x 12pcs
Lock Washer Ø1/4"
Flat Washer
Ø1/4"
#K x 12pcs
Bolt Ø1/4" x 1-1/2"
#I x 8pcs
Nut Ø5/16"
Parts List
Hardware List
Page4 of 8
#1
#2R
#2L
#4
#4
#3
#7
#5
#6
#8
#9
#10
#11 x2pcs
Dusty Panel
#11
#11

Page5 of 8
#A x 12pcs
#B x 12pcs
#C x 12pcs
#5
#2R
#2L
#1
#A #B #C
#D
#3
#7
#D
#A
#B
#C
2) Align HB legs (#2R/L) to the holes of the headboard
(#1), then secure by using bolts (#A) with washers (#B,C).
1) Align HB support (#5) to the holes
of the HB legs (#2R/L), then secure
by using bolts (#A) with washers
(#B,C).
1) Use a small amount of force to pull the drawers out from the footboard (#3).
2) Attach support legs (#7) to the holes of the footboard (#3). Adjust
leveler on the support legs (#7) according to ground level.

Page6 of 8
#6
#E
#9
#9
#E x 5pcs
#8
Align slat center support (#9) to the holes of the slat kit (#6),
then secure by using screws (#E).
Attach slat support legs (#8) to the holes of the slat center support (#9).
Adjust the leveler of the support legs (#8) according to ground level.

Page7 of 8
#E x 10pcs
#4
#1
#E
#4
#3
#G
#H
#I
#F x 8pcs
#G x 8pcs
#I x 8pcs
#F
Attach threaded studs (#F) to the holes of the
headboard (#1) and footboard (#3), then align
side rails (#4) to the threaded studs (#F) of the
headboard (#1) and footboard (#3). Secure by
using washers (#I) and hex nuts (#G).
Align slats to the side rails,
then secure by using screws
(#E).
Insert drawers back into
footboard.

Page8 of 8
#11
#K x 12pcs
#L x 12pcs
#M x 12pcs
#K
#L
#M
#D
#10
#4
#11
Place dusty panels (#11) to the
bed frame.
Align top bed rails (#10) to wash side rails, then secure by
using bolts (#K) with washers (#L,M).