Furniture of America HFW-1545C5 User manual

Page 1 of 12
REV.1
5-08-3
HFW-1545C5

Page 2 of 12

Page 3 of 12

Page 4 of 12

Page 5 of 12
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS

END TABLE
ASSEMBLY INSTRUCTIONS MODEL # HFW-1545C5
please keep for future reference PARTS LIST
HARDWARE LIST
120PCS 220PCS 332PCS 44PCS 51PC 68PCS
7 8
DIMENSIONS : 21.6"(W)*15.7"(D)19.6"(H)
Page 6 of 12
9 10 2PCS 11 2PCS4PCS
1PC
A2PCS 1PCC
B
1PC 1PC
ED 2PCS
1PCG
F
1PC 2PCSIH
2PCS 2PCS
K2PCS LJ
2PCS
M2PCSN
4PCS
A
B
B
C
K
KE
2PCS 1PCPO
8PCS 12 2PCS
13 2PCS 14 4PCS 15 4PCS 16 4PCS

Hardware 3 x 2 pcs
Hardware 7 x 4 pcs
Hardware 8 x 8 pcs
STEP : 1
ASSEMBLY INSTRUCTIONS
Assembly Drawer's Runners (a.k.a. Rails, Glides, Slides or Guides)
An assembly of ONE drawer requires two sets of runners. The runner is composed of
an inner rail and outer slide. Please read completely first before assembling.
Mounting the Inner Rail (Fixed) of the Runner: Before mounting, please determine
which side of the panel is the front and rear. The single screw hole on the outer slide
MUST be positioned on the FRONT of the panel. Place the inner rail of the runner in
its correct position and flat on its back. Slide the outer slide out to the way to align the
center or second holes on both ends of the inner rail with the pre-drilled holes on the
panel. For most applications, the center or second holes are used but if not, just make
sure the appropriate rail holes are aligned up with the panel holes. Use two screws to
secure the inner rail of the runner onto the panel.
Mounting the Outer Slide (Moveable) of the Runner: Each outer rail is secured with
a single screw onto the FRONT SIDE of drawer. Extend the two outer sliders of the
runners and place the drawer in between those two outer slides. Align the pre-drilled
holes on each side of the drawer with the screw holes of the outer slides. Use two
screws to secure from the inside of the drawer into the screw holes of the outer slides.
Page 7 of 12
Front
E
3
7
Front
D
3
87
8

X 2
ASSEMBLY INSTRUCTIONS
STEP : 2
Page 8 of 12
Hardware 1 x 20 pcs
Hardware 3 x 30 pcs
Hardware 10 x 2 pcs
Hardware 11 x 2 pcs
Hardware 13 x 2 pcs
Hardware 14 x 4 pcs
Dowel hole
B
G
3
IX 2 X 2
K
13
X 2
J
X 2 X 2

ASSEMBLY INSTRUCTIONS
STEP : 3
Page 9 of 12
Hardware 4 x 4 pcs
D
E
G
H
STEP : 4
Hardware 2 x 8 pcs
E
D
B
B
P
C
2
Finish

ASSEMBLY INSTRUCTIONS
Page 10 of 12
Hardware 2 x 4 pcs
Hardware 12 x 2 pcs
STEP : 5
10
10
12
12
2
Dowel hole
LN
O
K
X 2
Hardware 2 x 4 pcs
Hardware 6 x 8 pcs
STEP : 6
I
I
J
J

ASSEMBLY INSTRUCTIONS
Page 11 of 12
Hardware 2 x 4 pcs
Hardware 9 x 4 pcs
Hardware 15 x 4 pcs
STEP : 8 Extend the two outer slides of the runners so that they
are align with the sides of the drawer. Make sure the
pre-drilled holes from the drawer align with the screw
holes of the outer slides. Secure two screws from the
inside of the drawer using a Philips srewdriver to
tighten them to the outer sliders.

ASSEMBLY INSTRUCTIONS
Page 12 of 12
STEP : 10
ASSEMBLY IS COMPLETED
Make sure the unit is rested on a flat
surface and does not feel loose or
wobbly. If it does, double check all
bolts/screws are secured and properly
tightened.
STEP : 9
16
16
16
Hardware 16 x 4 pcs