Furniture of America CM7675CK User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 6
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7675CK
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Rev:16-11-28
Allen Wrench (Included)
Phillips Screwdriver
Wrench
(Included)
(Not Included)
For more information contact our team: [email protected]

Page 2 of 6
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

Parts List
Hardware List
#1 x 1pc
#2 x 1pc
#G x 8pcs
Screw #4 x 1-1/4"
#D x 8pcs
#A x 6pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Headboard Panel
#3 x 2pcs
#6 x 4pcs
#7 x 8pcs Ø1/4"
#5 x 2pcs
Page 3 of 6
#4 x 2pcs
Footboard
Bed Rail
Thread bolt Ø5/16" x 3-1/4"
Headboard Leg (L&R)
Footboard leg
Support Leg 190 x 30 x 30mm
Bed Slat
#E x 8pcs
#F x 8pcs
Curve washer Ø5/16"
Hex nut Ø5/16" x 3/4"
Bolt Ø5/16" x 1-5/8"
#B x 6pcs
#C x 6pcs
Lock Washer Ø5/16"
Flat Washer Ø5/16"
#H x 1pc
Wrench
#I x 1pc
Allen Wrench M4

Page 4 of 6
# A x 6pcs
#B x 6pcs
# C x 6pcs
#1
#4R
#4L
#C #B
#A
#I
#5
#5
#2
Prepare 6 bolts assembly by inserting lock washer (#B), then flat washer (#C)
onto bolts (#A). Align headboard legs (#4R/L) to the holes of the headboard
(#1). Secure with bolts (#A).
Attach 2 footboard legs (#5) to the footboard (#2).

Page 5 of 6
#D x 8pcs
#E x 8pcs
#F x 8pcs #1
#3
#3
#2
#D
#E
#F
#H
#7
#6
x4
#7
2) Align thread bolt (#D) to
the holes of the curve washer
(#E) and hex nut (#F). Then
secure by using the wrench
(#H).
1) Attach the thread bolts (#D) to the
headboard (#1) and footboard (#2).
Place curve washer (#E), then hex nut
(#F) into the holes of the bed rails (#3).
Attach 2 support legs (#7) to each bed slats (#6). Adjust
the floor protector according to ground level.

Page 6 of 6
ASSEMBLY IS COMPLETED
#G x 8pcs
#G
#3
#3
#6
#6
Align the slats (#6) to the bed rails (#3),
then secure with screws (#G).