Furniture of America Francesca CM7911 User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-05-30
Page 1 of 7
DIFFICULT
ASSEMBLY RATING
CM7911
Wrench
(Not Included)
Set Includes Pre-Assembled Nightstand
2 PERSONS RECOMMENDED

Page 2 of 7

Parts List
#1 x 1 pc
Dresser
#3 x 2 pcs
Mirror Support Rail
#5 x 2 pcs
Leg
#2 x 1 pc
Mirror
#4 x 1 pc
Headboard
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 7
#4
#5
#5
#6 x 1 pc
Shelf

#D x 22 pcs
Flat Washer
Hardware List
#A x 8 pcs
Bolt 1/4”x1-3/8”
#C x 6 pcs
Bolt 5/16”x1-9/16”
#G x 1 pc
Allen Wrench
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around
during the assembly. ALWAYS have at least two
people to help with transporting and assembling the
product to avoid any potential injury and/or damage,
especially with the fragile nature of the mirror.
Page 4 of 7
#I x 4 pcs
Wood Screw
#F x 4 pcs
Hex Nut
#J x 4 pcs
Shelf Support
#B x 4 pcs
Bolt 1/4”x2-9/16”
#E x 22 pcs
Lock Washer
#H x 1 pc
Machine Screw
#K x 1 pc
Knob

Page 5 of 7
Turn right (clockwise) to tighten
Insert 4 shelf supports (#J) into the holes behind the door of the
dresser (#1). Tilt the shelf (#6) at an angle and gently have it
rested and leveled on top of all 4 of the shelf supports (#J).
#I x 4 pcs
#J x 4 pcs
#H x 1 pc
#K x 1 pc
The machine screw (#H) is already assembled onto the knob
(#K) from the factory. Remove the machine screw (#H) using a
Phillips screwdriver from the knob (#K) and secure the knob
(#K) onto the door of the dresser (#1) using the same screw.
#K
#H
Optional step to secure the
shelf onto the shelf supports
using the wood screws (#I).
#1
#1

I. The two mirror support
brackets (#3) are already
attached behind the dresser.
Position the mirror support
brackets (#3) vertically to
align with the pre-drilled hole
of the dresser (#1)AND the
mirror (#2).
II. Prepare 6 bolt assemblies by
inserting FIRST the lock
washer (#E) onto the bolt
(#A) and then the flat washer
(#D) onto the SAME bolt
(#A), in that order.
III. Insert those bolt assemblies
onto the mirror support
brackets (#3) and secure
those bolts using an Allen
wrench (#G) to lock them in
with the dresser (#1)AND the
mirror (#2).
IV. Tighten all bolts, including
those that were already
attached from the factory.
Page 6 of 7
Turn right (clockwise) to tighten
I. Align the legs (#5) with the pre-drilled holes of the headboard (#4).
II. Prepare 6 bolt assemblies by inserting FIRST the lock washer (#E) onto the
bolt (#C) and then the flat washer (#D) onto the SAME bolt (#C), in that
order.
III. Insert the bolt assemblies through the back of the legs (#5) and secure those
bolts using the Allen wrench (#G) to lock them in with the headboard (#4).
#C x 6 pcs
#D x 6 pcs
#E x 6 pcs
#A x 8 pcs
#D x 8 pcs
#E x 8 pcs
Turn right (clockwise) to tighten
Back Side
Back Side
#3
Back Side

This is an optional step to assemble the headboard with the bed
frame (sold separately). Align the holes of the completed
headboard with the holes of the bed frame. Insert the bolts and
washers according to diagram below.
Turn right (clockwise) to tighten
Page 7 of 7
#B x 4 pcs
#D x 8 pcs
#E x 8 pcs
#F x 4 pcs
ASSEMBLY IS COMPLETED
(sold separately)