Furniture of America CM7683Q User manual

I. Insert 1 wood dowel (#I) into the top pre-drilled holes on each end of the headboard (#1).
II. Align the right headboard leg (#2R) and left headboard leg (#2L) to the pre-drilled holes
on the ends of the headboard (#1).
III. Prepare 6 bolt assemblies by FIRST inserting the lock washer (#B) onto the bolt (#A) then
the flat washer (#C) onto that SAME bolt (#A), in that order. Secure using the Allen wrench (#D).
Insert threaded end of footboard legs (#4) into the pre-drilled holes on the
bottom of the footboard (#3). Tighten clockwise by hand.

Insert threaded end of drawer
support legs (#5) into the pre-
drilled holes on the bottom
of the footboard (#3).
Adjust the leveler according to the
ground level. To lower or to raise the
slat support leg, you need to turn the
leveler clockwise or counterclockwise,
respectively.
Hook the ends of the side rails (#6) into the designated
slots along the headboard legs and footboard (#3).

Insert the threaded ends of the rail support legs (#9) into
the pre-drilled holes on the support rail (#8). Tighten by hand.
Adjust the leveler according to the
ground level. To lower or to raise
the slat support leg, you need to
turn the leveler clockwise or
counterclockwise, respectively.
I. Apply the slat kit (#7). Make
sure the pre-drilled holes align.
II. Prepare 2 bolt assemblies by
FIRST inserting the lock
washer (#F) onto the bolt (#E)
then the flat washer (#G) onto
that SAME bolt (#E). Insert into
the two slats that have a
centered pre-drilled hole and
secure using the Allen wrench
(#D).

Align the ends of the slat kit (#7) to the pre-
drilled holes along the sides of the side rails
(#6). Insert a wood screw (#H) into each end
and secure using a Phillips screwdriver.
Make sure all bolts are firmly secured.
ASSEMBLY IS COMPLETED

I. Insert 1 wood dowel (#I) into the top pre-drilled holes on each end of the headboard (#1).
II. Align the right headboard leg (#2R) and left headboard leg (#2L) to the pre-drilled holes
on the ends of the headboard (#1).
III. Prepare 6 bolt assemblies by FIRST inserting the lock washer (#B) onto the bolt (#A) then
the flat washer (#C) onto that SAME bolt (#A), in that order. Secure using the Allen wrench (#D).
Insert threaded end of footboard legs (#4) into the pre-drilled holes on the
bottom of the footboard (#3). Tighten clockwise by hand.

Insert threaded end of drawer
support legs (#5) into the pre-
drilled holes on the bottom
of the footboard (#3).
Adjust the leveler according to the
ground level. To lower or to raise the
slat support leg, you need to turn the
leveler clockwise or counterclockwise,
respectively.
Hook the ends of the side rails (#6) into the designated
slots along the headboard legs and footboard (#3).

Insert the threaded ends of the rail support legs (#9) into
the pre-drilled holes on the support rail (#8). Tighten by hand.
Adjust the leveler according to the
ground level. To lower or to raise
the slat support leg, you need to
turn the leveler clockwise or
counterclockwise, respectively.
I. Apply the slat kit (#7). Make
sure the pre-drilled holes align.
II. Prepare 2 bolt assemblies by
FIRST inserting the lock
washer (#F) onto the bolt (#E)
then the flat washer (#G) onto
that SAME bolt (#E). Insert into
the two slats that have a
centered pre-drilled hole and
secure using the Allen wrench
(#D).

Align the ends of the slat kit (#7) to the pre-drilled holes
along the sides of the side rails (#6). Insert a wood
screw (#H) into each end and secure using a Phillips
screwdriver.
ASSEMBLY IS COMPLETED
Make sure all bolts are firmly secured.