Furniture of America CM-AC6802 User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-03-27
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
CM-AC6802
Phillips Screwdriver (Not Included)

Page 2 of 5

Parts List Hardware List
#1 x 1 pc
Backrest
#2 x 1 pc
Seat Frame
#3 x 1 pc
Right Armrest
#A x 10 pcs
Bolt
#B x 10 pcs
Flat Washer
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 10 pcs
Lock Washer
MD
#D x 1 pc
Allen Wrench
#4 x 1 pc
Left Armrest
Page 3 of 5
#E x 4 pcs
Screw
#5 x 2 pcs
Front Leg
#6 x 1 pc
Rear Left Leg
#7 x 1 pc
Rear Right Leg
#8 x 1 pc
Seat Cushion

Turn right (clockwise) to tighten
Page 4 of 5
#A x 3 pcs
#B x 3 pcs
#C x 3 pcs
Note: Right and left are
determined by standing
BEHIND the chair.
I. Place the backrest (#1) on a protected surface.
II. Align the right arm rest (#3) with the pre-drilled holes of the
backrest (#1).
III. Prepare 3 bolt assemblies by inserting FIRST the lock washer
(#C) onto the bolt (#A) and then the flat washer (#B) onto the
SAME bolt (#A), in that order.
IV. Insert the bolt assemblies through the pre-drilled holes of the
backrest (#1) and secure those bolts using the Allen wrench (#D)
to lock them in with the right armrest (#3).
Repeat Step 1 to assemble the left armrest (#4) onto the
backrest (#1).
Turn right (clockwise) to tighten
#A x 3 pcs
#B x 3 pcs
#C x 3 pcs

Page 5 of 5
Turn right (clockwise) to tighten
#A x 4 pcs
#B x 4 pcs
#C x 4 pcs
I. Align the seat frame (#2) with the
pre-drilled holes of the backrest
(#1) and the right and left armrest
(#3 & #4).
II. Prepare 4 bolt assemblies by
inserting FIRST the lock washer
(#C) onto the bolt (#A) and then the
flat washer (#B) onto the SAME
bolt (#A), in that order.
III. Insert the 2 bolt assemblies
through the seat frame (#2) using
the Allen wrench (#D) to lock them
in with the backrest (#1).
IV. Insert two bolt assemblies, one
through each side of the seat frame
(#2) using the Allen wrench (#D) to
lock them in with the right and left
armrest (#3 & #4).
Enlarged
ASSEMBLY IS COMPLETED
I. Carefully place the chair on its back and on a protected surface.
II. Align the threaded end of the front leg (#5) with the pre-drilled holes on the
bottom of the seat frame (#2) and tighten by hand until secured.
III. Insert the left and right rear legs (#6 & #7) into the pre-drilled holes on the
bottom of the seat frame (#2).
IV. Insert 4 screws (#E), two screws for each left and right rear leg (#6 & #7)
and secure those screws using the Phillips screwdriver to lock them in with
the seat frame (#2).