Furniture of America Luminar II CM3559PT User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Phillips Screwdriver
(Not Included)

Page 3 of 6

Parts List Hardware List
#1 x 1 pc
Table Top
#2 x 4 pcs
Leg
#3 x 1pc
Shelf
#A x 8 pcs
Bolt 5/16”x7/8”
#B x 8 pcs
Bolt 5/16”x7/8”
Before you begin, please read Page 3
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 8 pcs
Bolt 5/16”x1-1/4”
MD
#D x 16 pcs
Flat Washer
#4 x 1 pc
Glass Top
Page 4 of 6
#E x 16 pcs
Lock Washer
#F x 1 pc
Allen Wrench
#G x 4 pcs
Bracket
Due to the size and/or weight of this product, it is highly recommended that
the assembly should be done near the area of its intended location. Make
sure you have enough space to move around during the assembly.
ALWAYS have at least two people to help with transporting and assembling
the product to avoid any potential injury and/or damage.

I. Align the bracket (#G) with the pre-
drilled holes of the leg (#2).
II. Secure the brackets (#G) using the
Allen wrench (#F) to tighten the 4
bolts (#A) to lock them with the leg
(#2).
III. Repeat the process above for the
remaining 3 legs.
I. Align the shelf (#3) with the pre-drilled holes of the 4 legs (#2).
II. Prepare 8 bolt assemblies by inserting FIRST the lock washer
(#E) onto the bolt (#C) and then the flat washer (#D) onto the
SAME bolt (#C), in that order.
III. Insert the bolt assemblies through the holes of the shelf (#3) and
secure those bolts using the Allen wrench (#F) to lock them with
the 4 legs (#2).
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
Page 5 of 6
#C x 8 pcs
#D x 8 pcs
#E x 8 pcs
#A x 8 pcs
#G x 4 pcs

Page 6 of 6
Turn right (clockwise) to tighten
#B x 8 pcs
#D x 8 pcs
#E x 8 pcs
I. With the help of another person, carefully place the table top (#1)
facing down on a protective surface. Align the assembled
legs/shelf with the pre-drilled holes on the table top (#1).
II. Prepare 8 bolt assemblies by inserting FIRST the lock washer (#E)
onto the bolt (#B) and then the flat washer (#D) onto the SAME bolt
(#B), in that order.
III. Insert the bolt assemblies through the holes of the brackets (#G)
and secure those bolts using the Allen wrench (#F) to lock them
with the table top (#1).
#G
To install the batteries (not included),
remove the screw that holds the battery
cover by using a Phillips screwdriver.
Install new AA-size 1.5-volt alkaline
batteries with correct polarity (,) by
following the illustration inside the battery
cover. Close the battery cover and tighten
back the screw.
Caution:
Use batteries of the same type.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
Do not use rechargeable batteries.
Do not try to recharge non-rechargeable batteries.
Remove exhausted or corroded batteries.
If light is not used for more than a week, remove the batteries to prevent depletion and corrosion.
Place the glass top (#4) onto the table top
(#1). Make sure the table is rested on a flat
surface and does not feel loose or wobbly. If it
does, double check that the bolts/screws are
secured and properly tightened. #1