Furniture of America CM-BN6681 User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-03-11
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
CM-BN6681
Phillips Screwdriver
(Not Included)

Page 2 of 5

Parts List Hardware List
#1 x 1 pc
Backrest
#2 x 1 pc
Left Arm
#3 x 1 pc
Right Arm
#A x 4 pcs
Bolt 1/4”x2-1/2”
#B x 5 pcs
Bolt 1/4”x1-3/16”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 10 pcs
Screw
MD
#D x 10 pcs
Wood Dowel
Page 3 of 5
#E x 1 pc
Allen Wrench
#4 x 1 pc
Bench Cushion
#5 x 1 pc
Rear Support Rail
#6 x 1 pc
Front Support Rail

Step 1
Step 2 I. Insert the backrest (#1) onto the
left side arm (#2) and secure the
bolt (#A) through the left arm (#2)
using the Allen wrench (#E) to lock
it with the backrest (#1).
II. Insert the front support rail (#6)
onto the left arm and secure the
bolt (#A) through the left arm (#2)
using the Allen wrench (#E) to lock
it with the front support rail (#6).
III. Insert the rear support rail (#5)
onto the left side arm (#2).
IV. Repeat the above process to
assemble the right arm (#3) onto
the backrest (#1), the front
support rail (#6) and the rear
support rail (#5).
Turn right (clockwise) to tighten
Page 4 of 5
#D x 10 pcs
#A x 4 pcs
Enlarged
Note: Right and left is determined by standing in
FRONT of the bench in its upright position.
Insert two wood dowels (#D) onto the backrest (#1), four
wood dowels (#D) onto the rear support rail (#5) and four
wood dowels (#D) onto the front support rail (#6).

Page 5 of 5
Step 4
Step 3 I. Align the bench cushion (#4)
onto the assembled parts.
Insert 3 bolts (#B) onto the
rear support rail (#5) and
using an Allen wrench (#E)
to lock them down with the
bench cushion (#4).
II. Insert a bolt (#B) onto the left
arm (#2) and using an Allen
wrench (#E) to lock it down
with the bench cushion (#4).
Repeat the same for the right
arm (#3).
ASSEMBLY IS COMPLETED
I. Insert 6 screws (#C) onto the brackets of the rear support rail (#5)
AND the front support rail (#6) and using a Phillips screwdriver to
secure them down with the bench cushion (#4).
II. Insert 2 screws (#C) onto the left arm (#2) and using a Phillips
screwdriver to secure them down with the bench cushion (#4).
III. Repeat process II to secure the right arm (#3) onto the bench cushion
(#4).
Enlarged
Turn right (clockwise) to tighten
#B x 5 pcs
#5
#4
#3
#2
Carefully turn the completed
table upright. Make sure
the table is rested on a flat
surface and it does not feel
loose or wobbly. If it does,
double check that the bolts
are secured and properly
tighten.
#5
#6
#2
#3