FuzzDog The Gimp User manual

The Gimp
Germanium fuzz +++
Contents of this document are ©2015 Pedal Parts Ltd.
No reproduction permitted without the express written
permission of Pedal Parts Ltd. All rights reserved.

Schematic + BO
R1 220K
R2 470R
R3 5K1
R4 220K
R5 47K
R6 10K
CLR 2K2*
C1 10 elec
C2 100n
C3 2u2 elec**
C4 10u elec
C5 10u elec
Q1,2 PNP Ge***
Q3 2N3904
SANITY 5KC
GIRTH 500KC‡
CHOKE 10KB
GAG 10KB
THRUST 5KB
GRUNT 10KB
*2 x CLRs are required on the daughterboard. Use whatever you prefer as your
normal LED current limiter.
**Adjust to taste. Can be bigger or smaller.
***Typical Fuzz Face pair with hFE of ~70(Q1) / ~120(Q2). You can get good results
with a huge range of gains either side of those values. Normally AC128 or 2N404.
‡Can be 500KB, but the reverse log taper gives a better sweep.

Be very careful when soldering the diodes, LED and transistors. They’re very sensitive to heat. You should
use some kind of heat sink (crocodile clip or reverse action tweezers) on each leg as you solder them. Keep
exposure to heat to a minimum (under 2 seconds).
The long leg (anode) of the electrolytic capacitors go into the square pads.
Snap the small metal tag off the pots so they can be mounted flush in the box.
Pot mounts on the back side of the board. You can use vertical-mount pots or just wire up ‘normal’ ones.
It’s a good idea to place the pots in their holes in the enclosure when you’re soldering them in place on the
PCB. That way you know they’re going to line up ok. Best way to do it is to solder a single pin of each pot in
place, then do a visual check to see that they’re all sitting at the same height. If not, melt the joints and re-
adjust any that are off.
If your pots don’t have protective plastic covers you should place a strip of thick card between them and the
board when soldering to keep them a good distance from the pcb to avoid shorting other components.
You should solder all other board-mounted
components before you solder the pots. Once
they’re in place you’ll have no access to much
of the underside of the board.
ake sure your footswtich lugs are horizontal
as shown in red above when soldering into the
daugherboard. It’s a good idea to place them
in the holes in the enclosure when doing this
to ensure they line up ok.
PCB Layout ©2015 Pedal Parts Ltd.

Ensure you mount the footswitches on the right side of the daughterboard. It’s clearly marked. Otherwise
your ribbon cable connections won’t line up.
The boards are designed for a 6-way ribbon cable connection between them, but you can use any wire you
want. just make sure you connect the correct pads.
LEDs
You should leave these until you’re actually boxing up the circuit. They don’t need to be in place for the
circuit to work, so plug it in and test it before you add them.
Pull them up through the PCB (short leg to square pad), and slightly bend the legs out so they don’t fall
back through. Position your daughterboard into the enclosure and lightly secure the footswitches. You
should now push the LEDs down through the PCB and located them into their holes in the enclosure. Once
done, tighten the footswitches, check the LEDs are still in place, then solder them in.
WHY IS THERE AN EXTRA PAD FOR THE SANITY BYPASS FOOTSWITCH LED...?
Yes. You can use a bi-colour LED in there if you want, i.e. green for normal, red for ORE.
Use a common-anode LED.
IN OUT
WIRING
Couldn’t be much easier really. Once you have the daughterboard and main circuit connected (hopefully
you’ve used a 6-way ribbon cable for extra simplicity and neatness), there are only six wires to connect as
shown below.

Drilling template
Hammond 1590BB
91 x 116 x x 31mm
The Gimp
Recommended drill sizes:
Pots 7mm
Jacks 10mm
Footswitch 12mm
DC Socket 12mm
Toggle Switch 6-7mm
This template is a rough guide only. You should ensure correct marking o your
enclosure be ore drilling. You use this template at your own risk.
Pedal Parts Ltd can accept no responsibility or incorrect drilling o enclosures.
PedalParts.co.uk
30mm
60mm
30mm
It’s a good idea to
drill the holes or
the pots 8mm to
give yoursel some
wiggle room unless
you’re a drill ninja