G-MORE GM37405 User manual

MODEL:GM37405
PRODUCTSIZE(LxWxH):320x392x250cm
PLEASEREADCAREFULLYBEFOREASSEMBLY
Greenhouse GM37405 Assembly instructions
www.ttshop.se

CONTENTS
1. Assembly Advice ................................................................Page 1
2. Product Features ................................................................Page 2 - 3
3. Part Lists .............................................................................Page 4 - 7
4. Roof Vents Assembly ..........................................................Page 8 - 12
6. Doors Assembly ..................................................................Page 13 - 19
7. Base Assembly ....................................................................Page 20 - 21
8. Framework Assembly ..........................................................Page 22 - 43
9. Panels Assembly .................................................................Page 44 - 52

11
Free ToolFree ToolFree ToolFree Tool
Assembly and Maintenance Advice
1. For safety purposes, we strongly recommend that this product is assembled by at least
two people.
2. Some components have sharp metal edges. Please be careful when handling metal
components. Please wear gloves, shoes and safety goggles during assembly.
3. Lay all of the components on a soft carpet or blanket to avoid any scratches or damages.
4. DO NOT climb or stand on the roof. Heavy articles should not be leaned against
the greenhouse.
5. Keep the roof and gutter clear of snow, dirt & leaves. Allowing snow to build up on
the roof may damage the product.
6. Unlike steel, if the paint finish is scratched this will not harm the aluminium underneath.
7. When your product needs cleaning, use a mild detergent solution and rinse with cold
clean water. Do not use acetone, abrasive cleaners or strong detergents to clean
the panels.
Tools Provided:
Component required but not provided:
Neutral Silicone Sealant
Tools Required when Assembly (Not Provided)
Assembly at least by two Persons

2
30mm 120mm 71mm
72mm
83mm
8&10mm 8&10mm
8&10mm
(8/10mm)PCPanel
4&6mm 4&6mm
4&6mm
(4/6mm)GlassPanel
* If you are glazing this greenhouse with glass you will need to slide the rubber gaskets
(provided) into the bar capping.
Functions and Features:
1. Compared with traditional greenhouses, this exciting new product features many significant
improvements. The hollow box profile aluminium framing is much stronger than other
greenhouses and it can withstand much greater pressure.
Wind resistance up to 12th typhoon (40M/S or 120KM/H). Weight Support 80KGS/M2,
Snow load capability over 40CM.
Gutter Profile Post
Traditional Greenhouse New Large Lean to Greenhouse
2. A great improvement for this new greenhouse is bigger bar capping and thicker connectors,
which are much neater and stronger. Another benefit is that these greenhouses can be
glazed with glass or polycarbonate of varying thicknesses.

Expansion
screw/Concrete
ground
3
3. Base anchor brackets are included as standard with expanding bolts to ensure a secure
fixing into concrete or paving. Alternatively, you can use the brackets to fix into a
timber base with wood screws.
5. The strong two part eaves beam includes an integral gutter. Downpipes are also included
as standard so you can collect rainwater.
7. Remove approximately 2 inches of film from all sheet edges before installing and remove
all film immediately after the construction is completed. Please ensure that the side
with the white film faces outwards.
4. Our unique frame connectors (2.5mm thick) make much stronger joints than conventional
greenhouses.
Steel bar/Lawn land
Manualopener Automaticopener
GM80001
6. Manual window handles are included as standard with the roof vents. If required,
automatic roof vent openers are available as an inexpensive optional extra.

GM37405
4
(ALU. Box No.1)
ALU. Box No. 1
L26A 2
L26B
L26C
2
4
L01B 2
L06 1
L07 1
D1
E1
F1
G1
L08A 2
L08B
L10
A
B
J01
1
1
2
2
4
PART NO QTY
L01A 2
L01C 2
L09 1
L14 1

5
GM37405
ALU. Box No. 2
(ALU. Box No.2)
L23B 4
L02B 4
L23C 24
L23D 12
L23A 5
L02A 3
L23N 2
L02K 16
L24A 16
L25A 2
L25B 2
L25C 2
L25D 2
L25E 2
L25F 2
L25G 2
L25H 2
L24D 1
L24E
L24F
L24G
L24H
L24I
1
1
1
1
1
L24B
L24C
2
6
PART NO QTY
L02D 1
L02E
L02F
L02G
L02H
L02I
1
1
1
1
1
L23E 16
L23F 4
K52
M6
PART NO QTY

6
ALU.BoxNo.3
GM37405(ALU.BoxNo.3)
L23C 18
1
L12D
1
L12F
L11A 4
L11D 9
1
L12H
18
L12K
1
L12E
1
L12G
L11C 2
1
L12I
3
L12A
L11E 2
L11B 4
4
L12B
PART NO QTY
L02K 2
PART NO QTY
W10 2
GM80001 2
8
4X10
Z03
Automatic Openers (Optional)
K4
W08 2
10
4X14D
Z02
S01
M6X12 9
Z4
M03
M6 9
W03 2
J02R/L 1/1
J03R/L 1/1
J06 2
J07 2
J08 2
2
4X14
Z01
J05 2
W06 2
Windowx2pcs
PART NO QTY
L13 1
L16A 8
L17 2
L18A 2
L16B 8
L18B 1
L18C 1
L18D 4
PART NO QTY
8
8
4X40
Z04
D4
S02 4
M8X30
M02
M8 4
L11H 8
L11J 8
J
Door
PART NO QTY
PART NO QTY
S03 14
M8X60
W05 14
Base
PART NO QTY
L19A 4
L19B 2
L20 2
L11F 4
L11G 4
W06 2
J8
4
Z03
4X10
Y10 2
L15A 2
4
4X14D
Z02
W12 2
W13 2
M01
M6 3

GM37405
PC/Glass
7
PART NO QTY
Y1 1
Y2 8
Y3 1
Y4 1
Y7 8
Y6 6
Y5 1
Y4
Y2
Y8
Y2
Y13
Y2
Y15
Y2
Y4
Y2
Y8
Y2
Y13
Y2
Y15
Y2
Y6 Y6
Y6 Y6
Y6 Y6
Y11 Y11
Y11 Y11
Y7 Y7
Y7 Y7
Y7 Y7
Y7 Y9
Y7 Y9 Y10
Y10
Y8 1
Y9 2
Y10 2
Y11 4
Y13 1
Y14 1
Y15 1
(PC/GLASS. Box)

PART NO QTY
L19A 4
L19B 2
L20 2
L11F 4
L11G 4
W06 2
J8
8
L20
L19B
L19A
L19A
B
B
B
B
Y10
L11F L11F
L11G
L11G
W06
4
Z03
4X10
Y10 2
L15A 2
4
4X14D
Z02
L15A
Roof Vents Assembly 2PCS

9
L20
L19B
L19A
L19A
J
J
J
J
1
1
2
2
L20
J
L19A J
L19A
L19B
1
2
Push down the button on
connector J before inserting it
into the end of the frame profile. After connector J has been fitted,
use the hole in the profile to tighten
the connector in place.

10
L11G
L11G
L11F
L11F Y10
Y10
First the glazing panel Y10 should be loosely retained by the bar capping profiles
L11F and L11G. Next tap the bar capping gently into position with a rubber mallet.

11
Z03 Z03
W06
Y10
Y10
Fix the W06 vent handles using Z03 screws.

12
Y10
L15A
Z02
1
2
Z02
L15A
212
Fill the gap with silicone sealant on 4 sides to avoid any leaking.

PART NO QTY
L13 1
L16A 8
L17 2
L18A 2
L16B 8
L18B 1
L18C 1
L18D 4
PART NO QTY
8
PART NO QTY
Y11 4
8
4X40
Z04
D4
S02 4
M8X30
M02
M8 4
13
L11H 8
L11J 8
J
Door Assembly

14
L18D
L16A
L16A
L16A
L16A
L17
L16B
L16B
L18D
J
JJ
J
L18A
L18B
LeftDoor
S02x2pcs
L18D
L16A&B
L18A&B&D
L17
L16A
L16A
1
1
1
1
22
1
2Z04
L18A/L18B
L16B
L17
L16A
L16A
then assemble the door frames using connector J, as shown in the
sketches below.
Put L16A into L17 and L18D and put L16B into L18A and L18B,
Push down the button on
connector J before inserting it
into the end of the frame profile.
Tighten L17 through
L18A/L18B with Z04.
After connector J has been fitted,
use the hole in the profile to tighten
the connector in place.

15
Y11
Y11
L11H
L11H
L11H
L11H
L11J
L11J
Y11 Y11
First the glazing panels should be loosely retained by the bar capping profiles L11H and L11J.
Next tap the bar capping gently into position with a rubber mallet,

16
M2
H100mm 100mm
29mm 29mm
L13
112
3
11
2
3
After Assembly
Slide 2xS02 into L18D, positioned 100mm away from each edge.
Secure S02 using M02 bolts, then rotate the wheels
to ensure free movement.
14.4mm
L13
L13
14.4mm
Attention: make sure you leave 14.4mm
space on both ends when you install L13

17
L18D
L16A
L16A
L16A
L16A
L17
L16B
L16B
L18D
J
JJ
J
L18C
L18A
S02x2pcs
L18D
L16A&B
L18A&B&D
L17
L16A
L16A
1
1
1
1
22
1
2Z04
L18A/L18C
L16B
L17
L16A
L16A
RightDoor then assemble the door frames using connector J, as shown in the
sketches below.
Put L16A into L17 and L18D and put L16B into L18A and L18C,
Push down the button on
connector J before inserting it
into the end of the frame profile.
Tighten L17 through
L18A/L18C with Z04.
After connector J has been fitted,
use the hole in the profile to tighten
the connector in place.

18
Y11 Y11
Y11
Y11
L11H
L11H
L11H
L11H
L11J
L11J
First the glazing panels should be loosely retained by the bar capping profiles L11H and L11J.
Next tap the bar capping gently into position with a rubber mallet,